libata version 1.10 loaded.
sata_promise version 1.01
ACPI: PCI interrupt 0000:00:08.0[A] -> GSI 18 (level, low) -> IRQ 18
sata_promise PATA port found
ata1: SATA max UDMA/133 cmd 0xFFFFC20000004200 ctl 0xFFFFC20000004238 bmdma 0x0 irq 18
ata2: SATA max UDMA/133 cmd 0xFFFFC20000004280 ctl 0xFFFFC200000042B8 bmdma 0x0 irq 18
ata3: PATA max UDMA/133 cmd 0xFFFFC20000004300 ctl 0xFFFFC20000004338 bmdma 0x0 irq 18
ata1: no device found (phy stat 00000000)
scsi0 : sata_promise
ata2: no device found (phy stat 00000000)
scsi1 : sata_promise
ata3: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4003 85:3469 86:3c01 87:4003 88:203f
ata3: dev 0 ATA, max UDMA/100, 312581808 sectors: lba48
ata3: dev 1 cfg 49:2f00 82:346b 83:7d01 84:4003 85:3469 86:3c01 87:4003 88:203f
ata3: dev 1 ATA, max UDMA/100, 312581808 sectors: lba48
ata3: dev 0 configured for UDMA/100
ata3: dev 1 configured for UDMA/100
scsi2 : sata_promise
  Vendor: ATA       Model: ST3160023A        Rev: 3.01
  Type:   Direct-Access                      ANSI SCSI revision: 05
  Vendor: ATA       Model: ST3160023A        Rev: 3.06
  Type:   Direct-Access                      ANSI SCSI revision: 05
sata_via version 1.1
ACPI: PCI interrupt 0000:00:0f.0[B] -> GSI 20 (level, low) -> IRQ 20
sata_via(0000:00:0f.0): routed to hard irq line 4
ata4: SATA max UDMA/133 cmd 0xD000 ctl 0xC802 bmdma 0xB800 irq 20
ata5: SATA max UDMA/133 cmd 0xC400 ctl 0xC002 bmdma 0xB808 irq 20
Losing some ticks... checking if CPU frequency changed.
ata4: no device found (phy stat 00000000)
scsi3 : sata_via
ata5: no device found (phy stat 00000000)
scsi4 : sata_via
SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB)
SCSI device sda: drive cache: write back
 sda:
Attached scsi disk sda at scsi2, channel 0, id 0, lun 0
SCSI device sdb: 312581808 512-byte hdwr sectors (160042 MB)
SCSI device sdb: drive cache: write back
SCSI device sdb: 312581808 512-byte hdwr sectors (160042 MB)
SCSI device sdb: drive cache: write back
 sdb: unknown partition table
Attached scsi disk sdb at scsi2, channel 0, id 1, lun 0
Attached scsi generic sg0 at scsi2, channel 0, id 0, lun 0,  type 0
Attached scsi generic sg1 at scsi2, channel 0, id 1, lun 0,  type 0