[Cluster-devel] [PATCH] gfs2: add native setup to man page

[Andrew Price]

Hi,

Looks good to me. Just a couple of tweaks:

On 13/05/13 17:09, David Teigland wrote:
> List the simplest sequence of steps to manually
> set up and run gfs2/dlm.
>
> Signed-off-by: David Teigland <teigland at redhat.com>
> ---
>   gfs2/man/gfs2.5 | 188 ++++++++++++++++++++++++++++++++++++++++++++++++++++++++
>   1 file changed, 188 insertions(+)
>
> diff --git a/gfs2/man/gfs2.5 b/gfs2/man/gfs2.5
> index 25effdd..eb12934 100644
> --- a/gfs2/man/gfs2.5
> +++ b/gfs2/man/gfs2.5
> @@ -196,3 +196,191 @@ The GFS2 documentation has been split into a number of sections:
>   \fBgfs2_tool\fP(8) Tool to manipulate a GFS2 file system (obsolete)
>   \fBtunegfs2\fP(8) Tool to manipulate GFS2 superblocks
>
> +.SH SETUP
> +
> +GFS2 clustering is driven by the dlm, which depends on dlm_controld to
> +provide clustering from userspace.  dlm_controld clustering is built on
> +corosync cluster/group membership and messaging.
> +
> +Follow these steps to manually configure and run gfs2/dlm/corosync.
> +
> +.B 1. create /etc/corosync/corosync.conf and copy to all nodes
> +
> +In this sample, replace cluster_name and IP addresses, and add nodes as
> +needed.  If using only two nodes, uncomment the two_node line.
> +See corosync.conf(5) for more information.
> +
> +.nf
> +totem {
> +        version: 2
> +        secauth: off
> +        cluster_name: abc
> +}
> +
> +nodelist {
> +        node {
> +                ring0_addr: 10.10.10.1
> +                nodeid: 1
> +        }
> +        node {
> +                ring0_addr: 10.10.10.2
> +                nodeid: 2
> +        }
> +        node {
> +                ring0_addr: 10.10.10.3
> +                nodeid: 3
> +        }
> +}
> +
> +quorum {
> +        provider: corosync_votequorum
> +#       two_node: 1
> +}
> +
> +logging {
> +        to_syslog: yes
> +}
> +.fi
> +
> +.PP
> +
> +.B 2. start corosync on all nodes
> +
> +.nf
> +systemctl start corosync
> +.fi
> +
> +Run corosync-quorumtool to verify that all nodes are listed.
> +
> +.PP
> +
> +.B 3. create /etc/dlm/dlm.conf and copy to all nodes
> +
> +.B *
> +To use no fencing, use this line:
> +
> +.nf
> +enable_fencing=0
> +.fi
> +
> +.B *
> +To use no fencing, but exercise fencing functions, use this line:
> +
> +.nf
> +fence_all /bin/true
> +.fi
> +
> +The "true" binary will be executed for all nodes and will succeed (exit 0)
> +immediately.
> +
> +.B *
> +To use manual fencing, use this line:
> +
> +.nf
> +fence_all /bin/false
> +.fi
> +
> +The "false" binary will be executed for all nodes and will fail (exit 1)
> +immediately.
> +
> +When a node fails, manually run: dlm_tool fence_ack <nodeid>
> +
> +.B *
> +To use stonith/pacemaker for fencing, use this line:
> +
> +.nf
> +fence_all /usr/sbin/dlm_stonith
> +.fi
> +
> +The "dlm_stonith" binary will be executed for all nodes.  If
> +stonith/pacemaker systems are not available, dlm_stonith will fail and
> +this config becomes the equivalent of the previous /bin/false config.
> +
> +.B *
> +To use an APC power switch, use these lines:
> +
> +.nf
> +device  apc /usr/sbin/fence_apc ipaddr=1.1.1.1 login=admin password=pw
> +connect apc node=1 port=1
> +connect apc node=2 port=2
> +connect apc node=3 port=3
> +.fi
> +
> +Other network switch based agents are configured similarly.
> +
> +.B *
> +To use sanlock/watchdog fencing, use these lines:
> +
> +.nf
> +device wd /usr/sbin/fence_sanlock path=/dev/fence/leases
> +connect wd node=1 host_id=1
> +connect wd node=2 host_id=2
> +unfence wd
> +.fi
> +
> +See fence_sanlock(8) for more information.
> +
> +.B *
> +For other fencing configurations see dlm.conf(5) man page.
> +
> +.PP
> +
> +.B 4. start dlm_controld on all nodes
> +
> +.nf
> +systemctl start dlm
> +.fi
> +
> +Run "dlm_tool status" to verify that all nodes are listed.
> +
> +.PP
> +
> +.B 5. if using clvm, start clvmd on all nodes
> +
> +systemctl clvmd start
> +
> +.PP
> +
> +.B 6. make new gfs2 file systems
> +
> +mkfs.gfs -p lock_dlm -t cluster_name:fs_name -j num /path/to/storage
            ^
Missing a 2 here.

> +The cluster_name must match the name used in step 1 above.
> +The fs_name must be a unique name in the cluster.
> +The -j option is the number of journals to create, there must
> +be one for each node that will mount the fs.
> +
> +.PP
> +
> +.B 7. mount gfs2 file systems
> +
> +mount /path/to/storage /mountpoint
> +
> +Run "dlm_tool ls" to verify the nodes that have each fs mounted.
> +
> +.PP
> +
> +.B 8. shut down
> +
> +.nf
> +umount -a gfs2

This needs a -t

Andy

> +systemctl clvmd stop
> +systemctl dlm stop
> +systemctl corosync stop
> +.fi
> +
> +.PP
> +
> +.B More setup information:
> +.br
> +.BR dlm_controld (8),
> +.br
> +.BR dlm_tool (8),
> +.br
> +.BR dlm.conf (5),
> +.br
> +.BR corosync (8),
> +.br
> +.BR corosync.conf (5)
> +.br
> +
>