[edk2-devel] [PATCH v3 0/4] RPi: SD/WiFi ACPI updates

[Ard Biesheuvel]

On Wed, 17 Feb 2021 at 18:16, Jeremy Linton <jeremy.linton at arm.com> wrote:
>
> Hi,
>
> On 2/17/21 1:55 AM, Ard Biesheuvel via groups.io wrote:
> > On Wed, 17 Feb 2021 at 08:30, Jeremy Linton <jeremy.linton at arm.com> wrote:
> >>
> >> Hi,
> >>
> >> On 2/17/21 12:56 AM, Ard Biesheuvel wrote:
> >>> On Wed, 17 Feb 2021 at 07:18, jlinton <lintonrjeremy at gmail.com> wrote:
> >>>>
> >>>> From: Jeremy Linton <jeremy.linton at arm.com>
> >>>>
> >>>> The existing RPi3 ACPI entries for the Arasan
> >>>> and SDHCI controllers need updating to work
> >>>> with the RPi4. This is done by adding a caps
> >>>> override for the legacy Arasan controller and
> >>>> then adding an entirely new entry for the newer
> >>>> eMMC2 controller.
> >>>>
> >>>> Then we flip the default routing to make the eMMC2
> >>>> the default for the SD card, so that the WiFi can
> >>>> start working on the Arasan.
> >>>>
> >>>> Additional we add a menu item to enable the SDMA/ADMA2
> >>>> modes on the controller.
> >>>>
> >>>> v2->v3: Various small review tweaks, whitespace, wording
> >>>>               spelling, etc.
> >>>>
> >>>
> >>> What happened to the IORT change? Don't we need that to ensure that
> >>> Linux sizes ZONE_DMA appropriately?
> >>
> >> Ha, I gave up! There are more important things to fix, especially when I
> >> found another case that couldn't just be fixed by the IORT tweaking
> >> without more kernel patches.
> >>
> >
> > Which case is that?
>
> Some of these firmware/board revisions appear to need the 3G
> translation. The EMMC seems to be one of the devices who's DT
> descriptions are being modified by the lower level firmware (like the PCI).
>

Considering that the reason for the 1 GB device limit is the -3 GB DMA
translation, I'd assume that the former and the latter apply to the
same set of peripherals.

But are you saying the dma-ranges properties are manipulated by the VC
firmware? Or other DT properties related to DMA translation?

> >
> >
> >> The default in this set is PIO mode, no DMA, same as the Arasan. If I
> >> get motivated (or someone else does) they can pick up the pieces to
> >> finish turning the DMA on in linux. It also simplifies that IORT disable
> >> patch I posted separately since I don't have to worry about enabling it
> >> for a limit <2G.
> >>
> >
> > But having a 1 GB limit for only the eMMC2 in the IORT and a matching
> > _DMA method in its container should not trigger this error, I'd
> > assume.
>
> Well with stock linux, the device will configure, startup and corrupt data.
>

By 'this error', I mean the splat resulting from mismatching DMA
limits for XHCI between IORT and _DMA.

Is the reason for the data corruption understood?

>
> >
> >> The sdhci_caps_mask choice is what flags the device as not supporting
> >> DMA modes unless the user enables it. Yes this hurts perf, but not
> >> nearly as badly as disabling UHS mode because we can't lower the card
> >> voltage with the standard sdhci registers (rather having to depend on a
> >> nonstandard rpi mailbox call which isn't available without a _DSM() or
> >> something equally undesirable).
> >>
> >
> > Are you saying switching to the Arasan disabled UHS mode, and this is
> > why this is an improvement nonetheless?
>
> ? I'm not sure I understand. Right now in linux we don't have SD or
> wifi. With just the caps _DSD entry the arasan will configure but it
> runs PIO mode all the time (including with DT). The cap is needed
> because the arasan returns 0 in the standard SDHCI caps registers.
>
> The emmc2 supports faster modes, but we can't easily switch the voltage
> to support them because the standard voltage control registers aren't
> wired correctly (AFAIK). Given the change detection doesn't work right
> either (AFAIK), we could hack up the linux sdhci subsystem to not reset
> the card at startup and leave faster cards at 1.8V, but that is uglier
> than adding a _DSM() to forward the voltage change request to the rpi
> mailbox. But again we are hacking up the iproc (or sdhci_acpi) driver.
>
> IMHO, Given its just a perf thing, and this whole board is compromised
> in so many ways, it just isn't worth trying to support low voltage/UHS.
> Since the card is already running at the slower speeds, using PIO
> instead of DMA isn't a huge hit.

I could also argue that PIO at low speeds is worse then PIO at high
speeds, given that the CPU will be tied up for longer to transfer the
same amount of data.

> So then we don't have to have a 1G
> IORT, or dynamic _DMA translation.
>

Yes, that is obviously a win.

> But this set is about enabling both the SD and WiFi. The latter requires
> the SD to be bound to the emmc2. At the moment there isn't much in the
> way of a perf advantage to switching the SD from the Arasan to the
> emmc2, the benefit comes from being able to use the wifi..
>
>

Fair enough. I'm just slightly disappointed that we cannot use the
eMMC2 in DMA mode even for the lower speed, but I guess it is not the
end of the world.

If everyone else is on board with this approach, I'll pick these up tomorrow.

Thanks,
Ard.


-=-=-=-=-=-=-=-=-=-=-=-
Groups.io Links: You receive all messages sent to this group.
View/Reply Online (#71750): https://edk2.groups.io/g/devel/message/71750
Mute This Topic: https://groups.io/mt/80698778/1813853
Group Owner: devel+owner at edk2.groups.io
Unsubscribe: https://edk2.groups.io/g/devel/unsub [edk2-devel-archive at redhat.com]
-=-=-=-=-=-=-=-=-=-=-=-