<!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.0 TRANSITIONAL//EN">
<HTML>
<HEAD>
<META HTTP-EQUIV="Content-Type" CONTENT="text/html; CHARSET=UTF-8">
<META NAME="GENERATOR" CONTENT="GtkHTML/3.0.9">
</HEAD>
<BODY>
The key problem here is <BR>
<FONT COLOR="#737373"><I>Dec 22 20:11:22 localhost kernel: sdb : READ CAPACITY failed</I></FONT><BR>
I also saw the similar problem with my USB CompactFlash reader. My FC1 can only recognize the CF Reader the 1st time it is connected; after mounting the drive, unmounting it, disconnecting, reconnecting it, FC1 cannot recognize it with the same message as above.<BR>
<BR>
<BR>
Vào ngày Th 4 , 24/12/2003 lúc 02:41, 1072208461 viết rằng:
<BLOCKQUOTE TYPE=CITE>
<PRE><FONT COLOR="#737373"><I>I just got a SanDisk CRUZER 256MB USB memory thingy. It no workey!
The USB is on a VIA 8235 chip if that matters.
Could some of you gurus take a look at these messages and give me a
clue about what I need to do to get this device working. I suspect
that I'm missing a module, but I can't figure out what I need.
Sorry about the size of this messages. I've trimmed out all the stuff
that seemed irrelevant, but I didn't want to lose something
important.
Thanks,
John
Dec 22 20:11:21 localhost kernel: usb.c: registered new driver
usbdevfs
Dec 22 20:11:21 localhost kernel: usb.c: registered new driver hub
Dec 22 20:11:21 localhost kernel: usb-uhci.c: $Revision: 1.275 $ time
16:47:59
Dec 21 2003
Dec 22 20:11:21 localhost kernel: usb-uhci.c: High bandwidth mode
enabled
Dec 22 20:11:21 localhost kernel: PCI: Found IRQ 11 for device 00:10.0
Dec 22 20:11:21 localhost kernel: usb-uhci.c: USB UHCI at I/O 0xd400,
IRQ 11
Dec 22 20:11:21 localhost kernel: usb-uhci.c: Detected 2 ports
Dec 22 20:11:21 localhost kernel: usb.c: new USB bus registered,
assigned bus
number 1
Dec 22 20:11:21 localhost kernel: hub.c: USB hub found
Dec 22 20:11:21 localhost kernel: hub.c: 2 ports detected
Dec 22 20:11:21 localhost kernel: PCI: Found IRQ 3 for device 00:10.1
Dec 22 20:11:21 localhost kernel: usb-uhci.c: USB UHCI at I/O 0xd800,
IRQ 3
Dec 22 20:11:21 localhost kernel: usb-uhci.c: Detected 2 ports
Dec 22 20:11:21 localhost kernel: usb.c: new USB bus registered,
assigned bus
number 2
Dec 22 20:11:21 localhost kernel: hub.c: USB hub found
Dec 22 20:11:21 localhost kernel: hub.c: 2 ports detected
Dec 22 20:11:21 localhost kernel: PCI: Found IRQ 5 for device 00:10.2
Dec 22 20:11:21 localhost kernel: usb-uhci.c: USB UHCI at I/O 0xdc00,
IRQ 5
Dec 22 20:11:21 localhost kernel: usb-uhci.c: Detected 2 ports
Dec 22 20:11:21 localhost kernel: usb.c: new USB bus registered,
assigned bus
number 3
Dec 22 20:11:21 localhost kernel: hub.c: USB hub found
Dec 22 20:11:21 localhost kernel: hub.c: 2 ports detected
Dec 22 20:11:21 localhost kernel: usb-uhci.c: v1.275:USB Universal
Host
Controller Interface driver
Dec 22 20:11:21 localhost kernel: ehci_hcd 00:10.3: PCI device
1106:3104
Dec 22 20:11:21 localhost kernel: ehci_hcd 00:10.3: irq 10, pci mem
e1bba000
Dec 22 20:11:21 localhost kernel: usb.c: new USB bus registered,
assigned bus
number 4
Dec 22 20:11:21 localhost kernel: ehci_hcd 00:10.3: USB 2.0 enabled,
EHCI
1.00, driver 2003-Jun-19/2.4
Dec 22 20:11:21 localhost kernel: hub.c: USB hub found
Dec 22 20:11:21 localhost kernel: hub.c: 6 ports detected
Dec 22 20:11:21 localhost kernel: usb.c: registered new driver hiddev
Dec 22 20:11:21 localhost kernel: usb.c: registered new driver hid
Dec 22 20:11:21 localhost kernel: hid-core.c: v1.8.1 Andreas Gal,
Vojtech
Pavlik <vojtech@suse.cz>
Dec 22 20:11:21 localhost kernel: hid-core.c: USB HID support drivers
Dec 22 20:11:21 localhost kernel: hub.c: connect-debounce failed, port
2
disabled
Dec 22 20:11:21 localhost kernel: hub.c: new USB device 00:10.3-2,
assigned
address 2
Dec 22 20:11:21 localhost kernel: usb.c: USB device 2 (vend/prod
0x781/0x8185)
is not claimed by any active driver.
Dec 22 20:11:21 localhost kernel: hub.c: new USB device 00:10.2-1,
assigned
address 2
Dec 22 20:11:21 localhost kernel: usb.c: USB device 2 (vend/prod
0xaec/0x3050)
is not claimed by any active driver.
Dec 22 20:11:21 localhost kernel: Initializing USB Mass Storage
driver...
Dec 22 20:11:21 localhost kernel: usb.c: registered new driver
usb-storage
Dec 22 20:11:21 localhost kernel: scsi1 : SCSI emulation for USB Mass
Storage
devices
Dec 22 20:11:21 localhost kernel: Vendor: Generic Model: STORAGE
DEVICE
Rev: 1.25
Dec 22 20:11:21 localhost kernel: Type: Direct-Access
ANSI SCSI revision: 02
Dec 22 20:11:21 localhost kernel: scsi2 : SCSI emulation for USB Mass
Storage
devices
Dec 22 20:11:21 localhost kernel: Vendor: SOYO Model: USB
Storage-CFC
Rev: 0208
Dec 22 20:11:21 localhost kernel: Type: Direct-Access
ANSI SCSI revision: 02
Dec 22 20:11:21 localhost kernel: USB Mass Storage support registered.
Dec 22 20:11:21 localhost kernel: Attached scsi removable disk sda at
scsi1,
channel 0, id 0, lun 0
Dec 22 20:11:21 localhost kernel: Attached scsi removable disk sdb at
scsi2,
channel 0, id 0, lun 0
Dec 22 20:11:21 localhost kernel: SCSI device sda: 512000 512-byte
hdwr
sectors (262 MB)
Dec 22 20:11:21 localhost kernel: sda: Write Protect is off
Dec 22 20:11:21 localhost kernel: sda: sda1
Dec 22 20:11:21 localhost kernel: sdb: Unit Not Ready, sense:
Dec 22 20:11:21 localhost kernel: Current 00:00: sns = 70 2
Dec 22 20:11:21 localhost kernel: ASC=3a ASCQ= 0
Dec 22 20:11:22 localhost kernel: Raw sense data:0x70 0x00 0x02 0x00
0x00 0x00
0x00 0x0a 0x00 0x00 0x00 0x00 0x3a 0x00 0x00 0x00 0x00 0x00
Dec 22 20:11:22 localhost kernel: sdb : READ CAPACITY failed.
Dec 22 20:11:22 localhost kernel: sdb : status = 1, message = 00, host
= 0,
driver = 08
Dec 22 20:11:22 localhost kernel: Current sd00:00: sns = 70 2
Dec 22 20:11:22 localhost kernel: ASC=3a ASCQ= 0
Dec 22 20:11:22 localhost kernel: Raw sense data:0x70 0x00 0x02 0x00
0x00 0x00
0x00 0x0a 0x00 0x00 0x00 0x00 0x3a 0x00 0x00 0x00 0x00 0x00
Dec 22 20:11:22 localhost kernel: sdb : block size assumed to be 512
bytes,
disk size 1GB.
Dec 22 20:11:22 localhost kernel: sdb: I/O error: dev 08:10, sector 0
Dec 22 20:11:22 localhost kernel: I/O error: dev 08:10, sector 0
Dec 22 20:11:22 localhost kernel: unable to read partition table
Dec 22 20:11:22 localhost kernel: sdb: Unit Not Ready, sense:
Dec 22 20:11:22 localhost kernel: Current 00:00: sns = 70 2
Dec 22 20:11:22 localhost kernel: ASC=3a ASCQ= 0
Dec 22 20:11:22 localhost kernel: Raw sense data:0x70 0x00 0x02 0x00
0x00 0x00
0x00 0x0a 0x00 0x00 0x00 0x00 0x3a 0x00 0x00 0x00 0x00 0x00
Dec 22 20:11:22 localhost kernel: sdb : READ CAPACITY failed.
Dec 22 20:11:22 localhost kernel: sdb : status = 1, message = 00, host
= 0,
driver = 08
Dec 22 20:11:22 localhost kernel: Current sd00:00: sns = 70 2
Dec 22 20:11:22 localhost kernel: ASC=3a ASCQ= 0
Dec 22 20:11:22 localhost kernel: Raw sense data:0x70 0x00 0x02 0x00
0x00 0x00
0x00 0x0a 0x00 0x00 0x00 0x00 0x3a 0x00 0x00 0x00 0x00 0x00
Dec 22 20:11:22 localhost kernel: sdb : block size assumed to be 512
bytes,
disk size 1GB.
Dec 22 20:11:22 localhost kernel: sdb: Write Protect is off
Dec 22 20:11:22 localhost kernel: sdb: I/O error: dev 08:10, sector 0
Dec 22 20:11:22 localhost kernel: I/O error: dev 08:10, sector 0
Dec 22 20:11:22 localhost kernel: unable to read partition table
Dec 22 20:11:22 localhost kernel: Device not ready. Make sure there
is a disc
in the drive.
Dec 22 20:11:22 localhost kernel: sdb: Unit Not Ready, sense:
Dec 22 20:11:22 localhost kernel: Current 00:00: sns = 70 2
Dec 22 20:11:22 localhost kernel: ASC=3a ASCQ= 0
Dec 22 20:11:22 localhost kernel: Raw sense data:0x70 0x00 0x02 0x00
0x00 0x00
0x00 0x0a 0x00 0x00 0x00 0x00 0x3a 0x00 0x00 0x00 0x00 0x00
Dec 22 20:11:22 localhost kernel: sdb : READ CAPACITY failed.
Dec 22 20:11:22 localhost kernel: sdb : status = 1, message = 00, host
= 0,
driver = 08
Dec 22 20:11:22 localhost kernel: Current sd00:00: sns = 70 2
Dec 22 20:11:22 localhost kernel: ASC=3a ASCQ= 0
Dec 22 20:11:22 localhost kernel: Raw sense data:0x70 0x00 0x02 0x00
0x00 0x00
0x00 0x0a 0x00 0x00 0x00 0x00 0x3a 0x00 0x00 0x00 0x00 0x00
Dec 22 20:11:22 localhost kernel: sdb : block size assumed to be 512
bytes,
disk size 1GB.
Dec 22 20:11:22 localhost kernel: sdb: Write Protect is off
Dec 22 20:11:22 localhost kernel: sdb: I/O error: dev 08:10, sector 0
Dec 22 20:11:22 localhost kernel: I/O error: dev 08:10, sector 0
Dec 22 20:11:22 localhost kernel: unable to read partition table
Dec 22 20:11:22 localhost kernel: Device not ready. Make sure there
is a disc
in the drive.
Dec 22 20:11:22 localhost kernel: usb.c: registered new driver usblp
Dec 22 20:11:22 localhost kernel: printer.c: v0.11: USB Printer Device
Class
driver
Dec 22 20:12:24 localhost kernel: hub.c: USB device not accepting new
address
(error=-71)
Dec 22 20:12:24 localhost kernel: usb.c: USB disconnect on device
00:10.3-2
address 2
Dec 22 20:12:24 localhost kernel: hub.c: new USB device 00:10.3-2,
assigned
address 3
Dec 22 20:12:27 localhost usb.agent[3564]: missing kernel or user mode
driver
usb-storage
Dec 22 20:12:29 localhost kernel: usb-storage: host_reset() requested
but not
implemented
Dec 22 20:12:39 localhost kernel: scsi: device set offline - command
error
recover failed: host 1 channel 0 id 0 lun 0
Dec 22 20:12:39 localhost kernel: sdb: Unit Not Ready, sense:
Dec 22 20:12:39 localhost kernel: Current 00:00: sns = 70 2
Dec 22 20:12:39 localhost kernel: ASC=3a ASCQ= 0
Dec 22 20:12:39 localhost kernel: Raw sense data:0x70 0x00 0x02 0x00
0x00 0x00
0x00 0x0a 0x00 0x00 0x00 0x00 0x3a 0x00 0x00 0x00 0x00 0x00
Dec 22 20:12:39 localhost kernel: sdb : READ CAPACITY failed.
Dec 22 20:12:39 localhost kernel: sdb : status = 1, message = 00, host
= 0,
driver = 08
Dec 22 20:12:39 localhost kernel: Current sd00:00: sns = 70 2
Dec 22 20:12:39 localhost kernel: ASC=3a ASCQ= 0
Dec 22 20:12:39 localhost kernel: Raw sense data:0x70 0x00 0x02 0x00
0x00 0x00
0x00 0x0a 0x00 0x00 0x00 0x00 0x3a 0x00 0x00 0x00 0x00 0x00
Dec 22 20:12:39 localhost kernel: sdb : block size assumed to be 512
bytes,
disk size 1GB.
Dec 22 20:12:39 localhost kernel: sdb: Write Protect is off
Dec 22 20:12:39 localhost kernel: sdb: I/O error: dev 08:10, sector 0
Dec 22 20:12:39 localhost kernel: I/O error: dev 08:10, sector 0
Dec 22 20:12:39 localhost kernel: unable to read partition table
Dec 22 20:12:39 localhost kernel: Device not ready. Make sure there
is a disc
in the drive.
Dec 22 20:12:39 localhost kernel: sdb: Unit Not Ready, sense:
Dec 22 20:12:39 localhost kernel: Current 00:00: sns = 70 2
Dec 22 20:12:39 localhost kernel: ASC=3a ASCQ= 0
Dec 22 20:12:39 localhost kernel: Raw sense data:0x70 0x00 0x02 0x00
0x00 0x00
0x00 0x0a 0x00 0x00 0x00 0x00 0x3a 0x00 0x00 0x00 0x00 0x00
Dec 22 20:12:39 localhost kernel: sdb : READ CAPACITY failed.
Dec 22 20:12:39 localhost kernel: sdb : status = 1, message = 00, host
= 0,
driver = 08
Dec 22 20:12:39 localhost kernel: Current sd00:00: sns = 70 2
Dec 22 20:12:39 localhost kernel: ASC=3a ASCQ= 0
Dec 22 20:12:39 localhost kernel: Raw sense data:0x70 0x00 0x02 0x00
0x00 0x00
0x00 0x0a 0x00 0x00 0x00 0x00 0x3a 0x00 0x00 0x00 0x00 0x00
Dec 22 20:12:39 localhost kernel: sdb : block size assumed to be 512
bytes,
disk size 1GB.
Dec 22 20:12:39 localhost kernel: sdb: Write Protect is off
Dec 22 20:12:39 localhost kernel: sdb: I/O error: dev 08:10, sector 0
Dec 22 20:12:39 localhost kernel: I/O error: dev 08:10, sector 0
Dec 22 20:12:39 localhost kernel: unable to read partition table
--
fedora-list mailing list
fedora-list@redhat.com
To unsubscribe: </FONT><A HREF="http://www.redhat.com/mailman/listinfo/fedora-list"><U>http://www.redhat.com/mailman/listinfo/fedora-list</U></I></A></PRE>
</BLOCKQUOTE>
<PRE><TABLE CELLSPACING="0" CELLPADDING="0" WIDTH="100%">
<TR>
<TD>
Lê Hồng Bội<BR>
<A HREF="mailto:le.hong.boi@sg.netnam.vn"><U>le.hong.boi@sg.netnam.vn</U></A><BR>
Phone: +84 91 3715235<BR>
<A HREF="http://lhboi.tripod.com"><U>http://lhboi.tripod.com</U></A>
</TD>
</TR>
</TABLE>
</PRE>
</BODY>
</HTML>