Linux version 2.6.17-1.3001.fc5 (brewbuilder@ls20-bc2-14.build.redhat.com) (gcc version 4.1.1 20060525 (Red Hat 4.1.1-1)) #1 Sun Sep 17 13:45:38 EDT 2006
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
 BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000001f7d0000 (usable)
 BIOS-e820: 000000001f7d0000 - 000000001f7efc00 (reserved)
 BIOS-e820: 000000001f7efc00 - 000000001f7fb000 (ACPI NVS)
 BIOS-e820: 000000001f7fb000 - 000000001f800000 (reserved)
 BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
 BIOS-e820: 00000000fec00000 - 00000000fec02000 (reserved)
 BIOS-e820: 00000000fed20000 - 00000000fed9b000 (reserved)
 BIOS-e820: 00000000feda0000 - 00000000fedc0000 (reserved)
 BIOS-e820: 00000000ffb00000 - 00000000ffc00000 (reserved)
 BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
503MB LOWMEM available.
Using x86 segment limits to approximate NX protection
On node 0 totalpages: 128976
  DMA zone: 4096 pages, LIFO batch:0
  Normal zone: 124880 pages, LIFO batch:31
DMI 2.3 present.
ACPI: RSDP (v000 HP                                    ) @ 0x000fe270
ACPI: RSDT (v001 HP     099C     0x20040620 HP   0x00000001) @ 0x1f7efc84
ACPI: FADT (v002 HP     099C     0x00000002 HP   0x00000001) @ 0x1f7efc00
ACPI: MADT (v001 HP     099C     0x00000001 HP   0x00000001) @ 0x1f7efcb8
ACPI: MCFG (v001 HP     099C     0x00000001 HP   0x00000001) @ 0x1f7efd14
ACPI: SSDT (v001 HP       HPQPpc 0x00001001 MSFT 0x0100000e) @ 0x1f7f7ab1
ACPI: DSDT (v001 HP       DAU00  0x00010000 MSFT 0x0100000e) @ 0x00000000
ACPI: PM-Timer IO Port: 0x1008
ACPI: Local APIC address 0xfec01000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 6:13 APIC version 20
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode:  Flat.  Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 20000000 (gap: 1f800000:c0800000)
Detected 800.119 MHz processor.
Built 1 zonelists.  Total pages: 128976
Kernel command line: ro root=LABEL=/ audit=0 selinux=0 vga=791 3
audit: disabled (after initialization)
mapped APIC to ffffd000 (fec01000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
CPU 0 irqstacks, hard=c07c0000 soft=c07bf000
PID hash table entries: 2048 (order: 11, 8192 bytes)
Console: colour dummy device 80x25
Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
... MAX_LOCKDEP_SUBCLASSES:    8
... MAX_LOCK_DEPTH:          30
... MAX_LOCKDEP_KEYS:        2048
... CLASSHASH_SIZE:           1024
... MAX_LOCKDEP_ENTRIES:     8192
... MAX_LOCKDEP_CHAINS:      8192
... CHAINHASH_SIZE:          4096
 memory used by lock dependency info: 696 kB
 per task-struct memory footprint: 1200 bytes
sizeof(vma)=84 bytes
sizeof(page)=32 bytes
sizeof(inode)=644 bytes
sizeof(dentry)=172 bytes
sizeof(ext3inode)=904 bytes
sizeof(buffer_head)=52 bytes
sizeof(skbuff)=172 bytes
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 503960k/515904k available (2040k kernel code, 11376k reserved, 1070k data, 220k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 1602.77 BogoMIPS (lpj=3205551)
Security Framework v1.0.0 initialized
SELinux:  Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: afe9fbff 00000000 00000000 00000000 00000180 00000000 00000000
CPU: After vendor identify, caps: afe9fbff 00000000 00000000 00000000 00000180 00000000 00000000
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: After all inits, caps: afe9f3ff 00000000 00000000 00000040 00000180 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: Intel(R) Pentium(R) M processor 1.60GHz stepping 08
Checking 'hlt' instruction... OK.
ACPI: Core revision 20060707
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
checking if image is initramfs... it is
Freeing initrd memory: 921k freed
PM: Adding info for No Bus:platform
HP Compaq Laptop series board detected. Selecting BIOS-method for reboots.
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using MMCONFIG
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
PM: Adding info for acpi:acpi
ACPI: PCI Root Bridge [C002] (0000:00)
PCI: Probing PCI hardware (bus 00)
PM: Adding info for No Bus:pci0000:00
ACPI: Assume root bridge [\_SB_.C002] bus is 0
Boot video device is 0000:00:02.0
PCI quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO
PCI quirk: region 1100-113f claimed by ICH6 GPIO
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
PCI: Transparent bridge - 0000:00:1e.0
PCI: Bus #03 (-#06) is hidden behind transparent bridge #02 (-#03) (try 'pci=assign-busses')
Please report the result to linux-kernel to fix this permanently
ACPI: PCI Interrupt Routing Table [\_SB_.C002._PRT]
PM: Adding info for pci:0000:00:00.0
PM: Adding info for pci:0000:00:02.0
PM: Adding info for pci:0000:00:02.1
PM: Adding info for pci:0000:00:1d.0
PM: Adding info for pci:0000:00:1d.1
PM: Adding info for pci:0000:00:1d.2
PM: Adding info for pci:0000:00:1d.3
PM: Adding info for pci:0000:00:1d.7
PM: Adding info for pci:0000:00:1e.0
PM: Adding info for pci:0000:00:1e.2
PM: Adding info for pci:0000:00:1e.3
PM: Adding info for pci:0000:00:1f.0
PM: Adding info for pci:0000:00:1f.1
PM: Adding info for pci:0000:02:04.0
PM: Adding info for pci:0000:02:06.0
PM: Adding info for pci:0000:02:06.2
PM: Adding info for pci:0000:02:0e.0
ACPI: PCI Interrupt Routing Table [\_SB_.C002.C068._PRT]
ACPI: Embedded Controller [C004] (gpe 16) interrupt mode.
ACPI: Power Resource [C1C5] (on)
ACPI: PCI Interrupt Link [C0D8] (IRQs 10 *11)
ACPI: PCI Interrupt Link [C0D9] (IRQs *10 11)
ACPI: PCI Interrupt Link [C0DA] (IRQs *10 11)
ACPI: PCI Interrupt Link [C0DB] (IRQs *10 11)
ACPI: PCI Interrupt Link [C0EE] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [C0EF] (IRQs 10 *11)
ACPI: PCI Interrupt Link [C0F0] (IRQs *10 11)
ACPI: PCI Interrupt Link [C0F1] (IRQs 10 11) *0, disabled.
ACPI: Power Resource [C248] (off)
ACPI: Power Resource [C249] (off)
ACPI: Power Resource [C24A] (off)
ACPI: Power Resource [C24B] (off)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
PM: Adding info for No Bus:pnp0
PM: Adding info for pnp:00:00
PM: Adding info for pnp:00:01
PM: Adding info for pnp:00:02
PM: Adding info for pnp:00:03
PM: Adding info for pnp:00:04
PM: Adding info for pnp:00:05
PM: Adding info for pnp:00:06
PM: Adding info for pnp:00:07
PM: Adding info for pnp:00:08
PM: Adding info for pnp:00:09
PM: Adding info for pnp:00:0a
pnp: PnP ACPI: found 11 devices
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
pnp: 00:09: ioport range 0x4d0-0x4d1 has been reserved
pnp: 00:09: ioport range 0x1000-0x107f could not be reserved
pnp: 00:09: ioport range 0x1100-0x113f has been reserved
pnp: 00:09: ioport range 0x1200-0x121f has been reserved
PCI: Ignore bogus resource 6 [0:0] of 0000:00:02.0
PCI: Bus 3, cardbus bridge: 0000:02:06.0
  IO window: 00003000-000030ff
  IO window: 00003400-000034ff
  PREFETCH window: 20000000-21ffffff
  MEM window: 22000000-23ffffff
PCI: Bridge: 0000:00:1e.0
  IO window: 3000-3fff
  MEM window: d0000000-d03fffff
  PREFETCH window: 20000000-21ffffff
PCI: Setting latency timer of device 0000:00:1e.0 to 64
ACPI: PCI Interrupt 0000:02:06.0[A] -> GSI 18 (level, low) -> IRQ 169
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 7, 655360 bytes)
TCP bind hash table entries: 8192 (order: 6, 360448 bytes)
TCP: Hash tables configured (established 16384 bind 8192)
TCP reno registered
PM: Adding info for platform:pcspkr
apm: BIOS not found.
audit: initializing netlink socket (disabled)
audit(1158659361.080:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
ksign: Installing public key data
Loading keyring
- Added public key 576FD6A657A9B87E
- User ID: Red Hat, Inc. (Kernel Module GPG key)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
PM: Adding info for platform:vesafb.0
vesafb: framebuffer at 0xc0000000, mapped to 0xe0080000, using 3072k, total 7872k
vesafb: mode is 1024x768x16, linelength=2048, pages=4
vesafb: protected mode interface info at 00ff:44f0
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
ACPI: Transitioning device [C24C] to D3
ACPI: Transitioning device [C24C] to D3
ACPI: Fan [C24C] (off)
ACPI: Transitioning device [C24D] to D3
ACPI: Transitioning device [C24D] to D3
ACPI: Fan [C24D] (off)
ACPI: Transitioning device [C24E] to D3
ACPI: Transitioning device [C24E] to D3
ACPI: Fan [C24E] (off)
ACPI: Transitioning device [C24F] to D3
ACPI: Transitioning device [C24F] to D3
ACPI: Fan [C24F] (off)
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3] C4[C3])
ACPI: Processor [C000] (supports 8 throttling states)
ACPI: Thermal Zone [TZ1] (40 C)
ACPI: Thermal Zone [TZ2] (33 C)
ACPI: Thermal Zone [TZ3] (25 C)
ACPI: Thermal Zone [TZ4] (40 C)
PM: Adding info for No Bus:pnp1
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12ac
Non-volatile memory driver v1.2
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected an Intel 915GM Chipset.
agpgart: Detected 7932K stolen memory.
agpgart: AGP aperture is 256M @ 0xc0000000
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
PM: Adding info for platform:serial8250
ACPI: PCI Interrupt 0000:00:1e.3[B] -> GSI 22 (level, low) -> IRQ 177
PM: Adding info for No Bus:isa
RAMDISK driver initialized: 16 RAM disks of 16384K size 4096 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH6: IDE controller at PCI slot 0000:00:1f.1
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 16 (level, low) -> IRQ 185
ICH6: chipset revision 3
ICH6: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0x2580-0x2587, BIOS settings: hda:DMA, hdb:DMA
Probing IDE interface ide0...
hda: ST94011A, ATA DISK drive
PM: Adding info for No Bus:ide0
hdb: HL-DT-STCD-RW/DVD DRIVE GCC-4243N, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
PM: Adding info for ide:0.0
PM: Adding info for ide:0.1
Probing IDE interface ide1...
hda: max request size: 512KiB
hda: 78140160 sectors (40007 MB) w/2048KiB Cache, CHS=16383/255/63, UDMA(100)
hda: cache flushes supported
 hda: hda1 hda2 hda3 hda4 < hda5 hda6 hda7 hda8 hda9 >
ide-floppy driver 0.99.newide
Yenta: CardBus bridge found at 0000:02:06.0 [103c:099c]
Yenta: Using INTVAL to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:02:06.0, mfunc 0x01aa1b22, devctl 0x64
Yenta: ISA IRQ mask 0x0cf8, PCI irq 169
Socket status: 30000006
Yenta: Raising subordinate bus# of parent bus (#02) from #03 to #06
pcmcia: parent PCI bridge I/O window: 0x3000 - 0x3fff
cs: IO port probe 0x3000-0x3fff: clean.
pcmcia: parent PCI bridge Memory window: 0xd0000000 - 0xd03fffff
pcmcia: parent PCI bridge Memory window: 0x20000000 - 0x21ffffff
usbcore: registered new driver libusual
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
PNP: PS/2 Controller [PNP0303:C1C2,PNP0f13:C1C3] at 0x60,0x64 irq 1,12
PM: Adding info for platform:i8042
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
PM: Adding info for serio:serio0
mice: PS/2 mouse device common for all mice
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
TCP bic registered
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
PM: Adding info for serio:serio1
Using IPI Shortcut mode
PM: Adding info for serio:serio2
ACPI: (supports S0 S3 S4 S5)
Time: tsc clocksource has been installed.
Freeing unused kernel memory: 220k freed
Time: acpi_pm clocksource has been installed.
Write protecting the kernel read-only data: 392k
PM: Adding info for serio:serio3
PM: Adding info for serio:serio4
input: AT Translated Set 2 keyboard as /class/input/input0
Synaptics Touchpad, model: 1, fw: 6.2, id: 0x25a0b1, caps: 0xa04793/0x300000
serio: Synaptics pass-through port at isa0060/serio4/input0
input: SynPS/2 Synaptics TouchPad as /class/input/input1
PM: Adding info for serio:serio5

=============================================
[ INFO: possible recursive locking detected ]
2.6.17-1.3001.fc5 #1
---------------------------------------------
kseriod/142 is trying to acquire lock:
 (&ps2dev->cmd_mutex#2){--..}, at: [<c05fa8f2>] mutex_lock+0x21/0x24

but task is already holding lock:
 (&ps2dev->cmd_mutex#2){--..}, at: [<c05fa8f2>] mutex_lock+0x21/0x24

other info that might help us debug this:
4 locks held by kseriod/142:
 #0:  (serio_mutex){--..}, at: [<c05fa8f2>] mutex_lock+0x21/0x24
 #1:  (&serio->drv_mutex){--..}, at: [<c05fa8f2>] mutex_lock+0x21/0x24
 #2:  (psmouse_mutex){--..}, at: [<c05fa8f2>] mutex_lock+0x21/0x24
 #3:  (&ps2dev->cmd_mutex#2){--..}, at: [<c05fa8f2>] mutex_lock+0x21/0x24

stack backtrace:
 [<c0403f8e>] show_trace_log_lvl+0x58/0x171
 [<c040456d>] show_trace+0xd/0x10
 [<c040460a>] dump_stack+0x19/0x1b
 [<c0431410>] __lock_acquire+0x75f/0x986
 [<c0431ba8>] lock_acquire+0x4b/0x6b
 [<c05fa788>] __mutex_lock_slowpath+0xb3/0x1fc
 [<c05fa8f2>] mutex_lock+0x21/0x24
 [<c0583f26>] ps2_command+0x82/0x2ff
 [<c0589434>] psmouse_sliced_command+0x1c/0x5a
 [<c058c984>] synaptics_pt_write+0x21/0x45
 [<c0583e00>] ps2_sendbyte+0x48/0xec
 [<c0583fab>] ps2_command+0x107/0x2ff
 [<c0589072>] psmouse_probe+0x1d/0x68
 [<c0589fed>] psmouse_connect+0x100/0x227
 [<c05817e1>] serio_connect_driver+0x1e/0x2e
 [<c0581807>] serio_driver_probe+0x16/0x18
 [<c0542606>] driver_probe_device+0x45/0x92
 [<c054265b>] __device_attach+0x8/0xa
 [<c0541f9f>] bus_for_each_drv+0x3a/0x65
 [<c05426b5>] device_attach+0x58/0x6c
 [<c0541cdd>] bus_attach_device+0x16/0x2b
 [<c054113b>] device_add+0x1f8/0x2de
 [<c058225d>] serio_thread+0xcf/0x28e
 [<c042c2bf>] kthread+0xb0/0xdd
 [<c0401005>] kernel_thread_helper+0x5/0xb
DWARF2 unwinder stuck at kernel_thread_helper+0x5/0xb
Leftover inexact backtrace:
 [<c040456d>] show_trace+0xd/0x10
 [<c040460a>] dump_stack+0x19/0x1b
 [<c0431410>] __lock_acquire+0x75f/0x986
 [<c0431ba8>] lock_acquire+0x4b/0x6b
 [<c05fa788>] __mutex_lock_slowpath+0xb3/0x1fc
 [<c05fa8f2>] mutex_lock+0x21/0x24
 [<c0583f26>] ps2_command+0x82/0x2ff
 [<c0589434>] psmouse_sliced_command+0x1c/0x5a
 [<c058c984>] synaptics_pt_write+0x21/0x45
 [<c0583e00>] ps2_sendbyte+0x48/0xec
 [<c0583fab>] ps2_command+0x107/0x2ff
 [<c0589072>] psmouse_probe+0x1d/0x68
 [<c0589fed>] psmouse_connect+0x100/0x227
 [<c05817e1>] serio_connect_driver+0x1e/0x2e
 [<c0581807>] serio_driver_probe+0x16/0x18
 [<c0542606>] driver_probe_device+0x45/0x92
 [<c054265b>] __device_attach+0x8/0xa
 [<c0541f9f>] bus_for_each_drv+0x3a/0x65
 [<c05426b5>] device_attach+0x58/0x6c
 [<c0541cdd>] bus_attach_device+0x16/0x2b
 [<c054113b>] device_add+0x1f8/0x2de
 [<c058225d>] serio_thread+0xcf/0x28e
 [<c042c2bf>] kthread+0xb0/0xdd
 [<c0401005>] kernel_thread_helper+0x5/0xb
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
input: PC Speaker as /class/input/input2
hdb: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, DMA
Uniform CD-ROM driver Revision: 3.20
ieee80211_crypt: registered algorithm 'NULL'
ACPI: PCI Interrupt 0000:00:1e.2[A] -> GSI 21 (level, low) -> IRQ 193
PCI: Setting latency timer of device 0000:00:1e.2 to 64
ieee80211: 802.11 data/management/control stack, git-1.1.13
ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.1.2kmprq
ipw2200: Copyright(c) 2003-2006 Intel Corporation
intel8x0_measure_ac97_clock: measured 54735 usecs
intel8x0: clocking to 48000
PM: Adding info for ac97:0-0:AD1981B
ACPI: PCI Interrupt 0000:02:04.0[A] -> GSI 21 (level, low) -> IRQ 193
ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection
Floppy drive(s): fd0 is 1.44M
USB Universal Host Controller Interface driver v3.0
cs: IO port probe 0x100-0x3af: clean.
cs: IO port probe 0x3e0-0x4ff: clean.
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0xc00-0xcf7: clean.
cs: IO port probe 0xa00-0xaff: clean.
ieee1394: Initialized config rom entry `ip1394'
ipw2200: Detected geography ZZR (14 802.11bg channels, 0 802.11a channels)
b44.c:v1.01 (Jun 16, 2006)
ACPI: PCI Interrupt 0000:02:0e.0[A] -> GSI 16 (level, low) -> IRQ 185
eth1: Broadcom 4400 10/100BaseT Ethernet 00:12:79:59:57:42
ACPI: PCI Interrupt 0000:00:1e.3[B] -> GSI 22 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:00:1e.3 to 64
PM: Adding info for ac97:1-1:Si3036,8
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 201
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 201, io base 0x00002000
PM: Adding info for usb:usb1
PM: Adding info for No Bus:usbdev1.1_ep00
usb usb1: configuration #1 chosen from 1 choice
PM: Adding info for usb:1-0:1.0
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
PM: Adding info for No Bus:usbdev1.1_ep81
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 17 (level, low) -> IRQ 209
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 209, io base 0x00002020
PM: Adding info for usb:usb2
PM: Adding info for No Bus:usbdev2.1_ep00
usb usb2: configuration #1 chosen from 1 choice
PM: Adding info for usb:2-0:1.0
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
PM: Adding info for No Bus:usbdev2.1_ep81
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 169, io base 0x00002040
PM: Adding info for usb:usb3
PM: Adding info for No Bus:usbdev3.1_ep00
usb usb3: configuration #1 chosen from 1 choice
PM: Adding info for usb:3-0:1.0
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
PM: Adding info for No Bus:usbdev3.1_ep81
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 19 (level, low) -> IRQ 217
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.3: irq 217, io base 0x00002060
PM: Adding info for usb:usb4
PM: Adding info for No Bus:usbdev4.1_ep00
usb usb4: configuration #1 chosen from 1 choice
PM: Adding info for usb:4-0:1.0
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usb 1-2: new low speed USB device using uhci_hcd and address 2
PM: Adding info for No Bus:usbdev4.1_ep81
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 201
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 201, io mem 0xd0580000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
PM: Adding info for usb:usb5
PM: Adding info for No Bus:usbdev5.1_ep00
usb usb5: configuration #1 chosen from 1 choice
PM: Adding info for usb:5-0:1.0
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
PM: Adding info for No Bus:usbdev5.1_ep81
ACPI: PCI Interrupt 0000:02:06.2[C] -> GSI 22 (level, low) -> IRQ 177
PM: Adding info for ieee1394:fw-host0
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[177]  MMIO=[d0002000-d00027ff]  Max Packet=[2048]  IR/IT contexts=[4/8]
usb 1-2: new low speed USB device using uhci_hcd and address 3
PM: Adding info for usb:1-2
PM: Adding info for No Bus:usbdev1.3_ep00
usb 1-2: configuration #1 chosen from 1 choice
floppy0: no floppy controllers found
PM: Adding info for usb:1-2:1.0
input: Logitech Optical USB Mouse as /class/input/input3
input: USB HID v1.10 Mouse [Logitech Optical USB Mouse] on usb-0000:00:1d.0-2
PM: Adding info for No Bus:usbdev1.3_ep81
PM: Adding info for ieee1394:718b500029411fa6
ieee1394: Host added: ID:BUS[0-00:1023]  GUID[718b500029411fa6]
PM: Adding info for ieee1394:718b500029411fa6-0
Floppy drive(s): fd0 is 1.44M
floppy0: no floppy controllers found
lp: driver loaded but no devices found
ACPI: AC Adapter [C172] (off-line)
ACPI: Battery Slot [C174] (battery present)
ACPI: Battery Slot [C173] (battery absent)
ACPI: Power Button (FF) [PWRF]
ACPI: Sleep Button (CM) [C1E8]
ACPI: Lid Switch [C1E9]
ibm_acpi: ec object not found
ACPI: Video Device [C055] (multi-head: yes  rom: no  post: no)
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: dm-devel@redhat.com
EXT3 FS on hda2, internal journal
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hda3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hda9, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
ip_tables: (C) 2000-2006 Netfilter Core Team
Netfilter messages via NETLINK v0.30.
ip_conntrack version 2.4 (4030 buckets, 32240 max) - 228 bytes per conntrack
b44: eth0: Link is up at 100 Mbps, full duplex.
b44: eth0: Flow control is off for TX and off for RX.
