"Usman S. Ansari" <uansari@yahoo.com> wrote:<blockquote class="replbq" style="border-left: 2px solid rgb(16, 16, 255); margin-left: 5px; padding-left: 5px;"> <pre>>>>>> "USA" == Usman S Ansari <uansari yahoo com> writes: > USA> I am using x86_64 with FC 6 running, is this monitor supported ? > > Works fine for me. > > USA> any review about this monitor ? > > They seem nice enough to me. They can't be adjusted for height, which > is a drawback, but they are nice and bright. Color and brightness are > consistent across the four that I have in arm's reach at the moment. > The bezel is a bit large compared to, say, the Dell 2405 but they are > sturdy and quite inexpensive. > > - J< I got my AL2416Wbsd (thanks God). Rebooted my Linux box (I have FC 6 on x86_64). It correctly reconfigured for Acer AL 2416W monitor. Till this point well and good. Have two issues 1. It is not giving me option of 1920 X 1200, highest resolution is option 1600 X 1200. How can I fix this. Running at 60 HZ 2. Login as root, picture looks more sharper, I wonder what is different. Usman </pre></blockquote>lspci -vvv about my vedio card. 05:00.0 VGA compatible controller: ATI Technologies Inc RV370 5B60 [Radeon X300 (PCIE)] (prog-if 00 [VGA]) Subsystem: ASUSTeK Computer Inc. Extreme AX300SE-X Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0, Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 18 Region 0: Memory at d8000000 (32-bit, prefetchable) [size=128M] Region 1: I/O ports at 9e00 [size=256] Region 2: Memory at fe2f0000 (32-bit, non-prefetchable) [size=64K] [virtual] Expansion ROM at fe200000 [disabled] [size=128K] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [58] Express Endpoint IRQ 0 Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag+ Device: Latency L0s <128ns, L1 <2us Device: AtnBtn- AtnInd- PwrInd- Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported- Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ Device: MaxPayload 128 bytes, MaxReadReq 128 bytes Link: Supported Speed 2.5Gb/s, Width x16, ASPM L0s L1, Port 0 Link: Latency L0s <128ns, L1 <1us Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch- Link: Speed 2.5Gb/s, Width x16 Capabilities: [80] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable- Address: 0000000000000000 Data: 0000 05:00.1 Display controller: ATI Technologies Inc RV370 [Radeon X300SE] Subsystem: ASUSTeK Computer Inc. Unknown device 002b Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Region 0: Memory at fe2e0000 (32-bit, non-prefetchable) [disabled] [size=64K] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [58] Express Endpoint IRQ 0 Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag- Device: Latency L0s <128ns, L1 <2us Device: AtnBtn- AtnInd- PwrInd- Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported- Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- Device: MaxPayload 128 bytes, MaxReadReq 128 bytes Link: Supported Speed 2.5Gb/s, Width x16, ASPM L0s L1, Port 0 Link: Latency L0s <128ns, L1 <1us Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch- Link: Speed 2.5Gb/s, Width x16