Linux version 2.6.22.7-85.fc7 (kojibuilder@xenbuilder4.fedora.phx.redhat.com) (gcc version 4.1.2 20070502 (Red Hat 4.1.2-12)) #1 SMP Fri Sep 21 19:53:05 EDT 2007
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
 BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 0000000030000000 (usable)
 BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
768MB LOWMEM available.
Using x86 segment limits to approximate NX protection
Entering add_active_range(0, 0, 196608) 0 entries of 256 used
Zone PFN ranges:
  DMA             0 ->     4096
  Normal       4096 ->   196608
  HighMem    196608 ->   196608
early_node_map[1] active PFN ranges
    0:        0 ->   196608
On node 0 totalpages: 196608
  DMA zone: 32 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 4064 pages, LIFO batch:0
  Normal zone: 1504 pages used for memmap
  Normal zone: 191008 pages, LIFO batch:31
  HighMem zone: 0 pages used for memmap
DMI 2.3 present.
Using APIC driver default
Allocating PCI resources starting at 40000000 (gap: 30000000:cfff0000)
Built 1 zonelists.  Total pages: 195072
Kernel command line: ro root=/dev/VolGroup00/LogVol00 rhgb quiet acpi=off
Local APIC disabled by BIOS -- you can enable it with "lapic"
mapped APIC to ffffd000 (0160e000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
CPU 0 irqstacks, hard=c0793000 soft=c0773000
PID hash table entries: 4096 (order: 12, 16384 bytes)
Detected 866.413 MHz processor.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 771020k/786432k available (2111k kernel code, 14836k reserved, 1117k data, 260k init, 0k highmem)
virtual kernel memory layout:
    fixmap  : 0xffc56000 - 0xfffff000   (3748 kB)
    pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
    vmalloc : 0xf0800000 - 0xff7fe000   ( 239 MB)
    lowmem  : 0xc0000000 - 0xf0000000   ( 768 MB)
      .init : 0xc072d000 - 0xc076e000   ( 260 kB)
      .data : 0xc060fde8 - 0xc0727504   (1117 kB)
      .text : 0xc0400000 - 0xc060fde8   (2111 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
SLUB: Genslabs=22, HWalign=32, Order=0-1, MinObjects=4, CPUs=1, Nodes=1
Calibrating delay using timer specific routine.. 1733.86 BogoMIPS (lpj=866933)
Security Framework v1.0.0 initialized
SELinux:  Initializing.
SELinux:  Starting in permissive mode
selinux_register_security:  Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0383f9ff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU: After all inits, caps: 0383f1ff 00000000 00000000 00000040 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 14k freed
CPU0: Intel Pentium III (Coppermine) stepping 06
SMP motherboard not detected.
Local APIC not detected. Using dummy APIC emulation.
Brought up 1 CPUs
sizeof(vma)=84 bytes
sizeof(page)=32 bytes
sizeof(inode)=336 bytes
sizeof(dentry)=132 bytes
sizeof(ext3inode)=488 bytes
sizeof(buffer_head)=56 bytes
sizeof(skbuff)=176 bytes
sizeof(task_struct)=1536 bytes
Time:  2:29:51  Date: 10/15/07
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfb230, last bus=1
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI: disabled
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Using IRQ router VIA [1106/0596] at 0000:00:07.0
NetLabel: Initializing
NetLabel:  domain hash size = 128
NetLabel:  protocols = UNLABELED CIPSOv4
NetLabel:  unlabeled traffic allowed by default
Time: tsc clocksource has been installed.
PCI: Bridge: 0000:00:01.0
  IO window: d000-dfff
  MEM window: e4000000-e7ffffff
  PREFETCH window: disabled.
PCI: Setting latency timer of device 0000:00:01.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1572864 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 3496k freed
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
audit: initializing netlink socket (disabled)
audit(1192415392.001:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SELinux:  Registering netfilter hooks
ksign: Installing public key data
Loading keyring
- Added public key 5C8CFCE5A817ACD0
- User ID: Red Hat, Inc. (Kernel Module GPG key)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: VIA PCI bridge detected. Disabling DAC.
Activating ISA DMA hang workarounds.
Boot video device is 0000:01:00.0
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Generic RTC Driver v1.07
Non-volatile memory driver v1.2
Linux agpgart interface v0.102 (c) Dave Jones
agpgart: Detected VIA Apollo Pro 133 chipset
agpgart: AGP aperture is 64M @ 0xe0000000
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 16384K size 4096 blocksize
input: Macintosh mouse button emulation as /class/input/input0
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input1
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI No-Shortcut mode
  Magic number: 11:286:460
drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
Freeing unused kernel memory: 260k freed
Write protecting the kernel read-only data: 864k
USB Universal Host Controller Interface driver v3.0
uhci_hcd 0000:00:07.2: UHCI Host Controller
uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:07.2: irq 10, io base 0x0000e400
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
SCSI subsystem initialized
usb 1-1: new low speed USB device using uhci_hcd and address 2
libata version 2.21 loaded.
pata_via 0000:00:07.1: version 0.3.1
scsi0 : pata_via
scsi1 : pata_via
ata1: PATA max UDMA/66 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x0001e000 irq 14
ata2: PATA max UDMA/66 cmd 0x00010170 ctl 0x00010376 bmdma 0x0001e008 irq 15
usb 1-1: configuration #1 chosen from 1 choice
input: Logitech Optical USB Mouse as /class/input/input2
input: USB HID v1.10 Mouse [Logitech Optical USB Mouse] on usb-0000:00:07.2-1
ata1.00: ATA-6: ST380011A, 3.06, max UDMA/100
ata1.00: 156301488 sectors, multi 16: LBA48 
ata1.01: ATA-6: ST380011A, 8.54, max UDMA/100
ata1.01: 156301488 sectors, multi 16: LBA48 
ata1.00: configured for UDMA/66
ata1.01: configured for UDMA/66
ata2.00: ATAPI: PIONEER DVD-RW  DVR-107D, 1.15, max UDMA/33
ata2.01: ATAPI: HL-DT-STDVD-ROM GDR8162B, 0015, max UDMA/33
ata2.00: configured for UDMA/33
ata2.01: configured for UDMA/33
scsi 0:0:0:0: Direct-Access     ATA      ST380011A        3.06 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sda: sda1 sda2
sd 0:0:0:0: [sda] Attached SCSI disk
scsi 0:0:1:0: Direct-Access     ATA      ST380011A        8.54 PQ: 0 ANSI: 5
sd 0:0:1:0: [sdb] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:1:0: [sdb] Write Protect is off
sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:1:0: [sdb] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:1:0: [sdb] Write Protect is off
sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sdb: sdb1
sd 0:0:1:0: [sdb] Attached SCSI disk
scsi 1:0:0:0: CD-ROM            PIONEER  DVD-RW  DVR-107D 1.15 PQ: 0 ANSI: 5
scsi 1:0:1:0: CD-ROM            HL-DT-ST DVD-ROM GDR8162B 0015 PQ: 0 ANSI: 5
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
ata1.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
ata1.01: (BMDMA stat 0x64)
ata1.01: cmd c8/00:04:4d:00:00/00:00:00:00:00/f0 tag 0 cdb 0x0 data 2048 in
         res 51/84:01:50:00:00/00:00:00:00:00/f0 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1.00: configured for UDMA/66
ata1.01: configured for UDMA/66
ata1: EH complete
ata1.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
ata1.01: (BMDMA stat 0x64)
ata1.01: cmd c8/00:04:4d:00:00/00:00:00:00:00/f0 tag 0 cdb 0x0 data 2048 in
         res 51/84:01:50:00:00/00:00:00:00:00/f0 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1.00: configured for UDMA/66
ata1.01: configured for UDMA/66
ata1: EH complete
sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
ata1.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
ata1.01: (BMDMA stat 0x64)
ata1.01: cmd c8/00:04:4d:00:00/00:00:00:00:00/f0 tag 0 cdb 0x0 data 2048 in
         res 51/84:01:50:00:00/00:00:00:00:00/f0 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1.00: configured for UDMA/66
ata1.01: configured for UDMA/66
ata1: EH complete
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
ata1.01: limiting speed to UDMA/44:PIO4
ata1.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
ata1.01: (BMDMA stat 0x64)
ata1.01: cmd c8/00:04:4d:00:00/00:00:00:00:00/f0 tag 0 cdb 0x0 data 2048 in
         res 51/84:01:50:00:00/00:00:00:00:00/f0 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1.00: configured for UDMA/66
ata1.01: configured for UDMA/44
ata1: EH complete
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:1:0: [sdb] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:1:0: [sdb] Write Protect is off
sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:1:0: [sdb] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:1:0: [sdb] Write Protect is off
sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
audit(1192415402.989:2): enforcing=1 old_enforcing=0 auid=4294967295
security:  3 users, 6 roles, 1845 types, 82 bools, 1 sens, 1024 cats
security:  61 classes, 70170 rules
SELinux:  Completing initialization.
SELinux:  Setting up existing superblocks.
SELinux: initialized (dev dm-0, type ext3), uses xattr
SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev debugfs, type debugfs), uses genfs_contexts
SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts
SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs
SELinux: initialized (dev hugetlbfs, type hugetlbfs), uses genfs_contexts
SELinux: initialized (dev devpts, type devpts), uses transition SIDs
SELinux: initialized (dev inotifyfs, type inotifyfs), uses genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev futexfs, type futexfs), uses genfs_contexts
SELinux: initialized (dev anon_inodefs, type anon_inodefs), uses genfs_contexts
SELinux: initialized (dev pipefs, type pipefs), uses task SIDs
SELinux: initialized (dev sockfs, type sockfs), uses task SIDs
SELinux: initialized (dev cpuset, type cpuset), uses genfs_contexts
SELinux: initialized (dev proc, type proc), uses genfs_contexts
SELinux: initialized (dev bdev, type bdev), uses genfs_contexts
SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts
SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
audit(1192415403.451:3): policy loaded auid=4294967295
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 0:0:1:0: Attached scsi generic sg1 type 0
scsi 1:0:0:0: Attached scsi generic sg2 type 5
scsi 1:0:1:0: Attached scsi generic sg3 type 5
sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 1:0:0:0: Attached scsi CD-ROM sr0
sr1: scsi3-mmc drive: 20x/48x cd/rw xa/form2 cdda tray
sr 1:0:1:0: Attached scsi CD-ROM sr1
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
Linux Tulip driver version 1.1.15 (Feb 27, 2007)
PCI: setting IRQ 10 as level-triggered
PCI: Found IRQ 10 for device 0000:00:0c.0
tulip0:  EEPROM default media type Autosense.
tulip0:  Index #0 - Media MII (#11) described by a 21142 MII PHY (3) block.
tulip0:  MII transceiver #1 config 1000 status 782d advertising 01e1.
eth0: Digital DS21142/43 Tulip rev 65 at MMIO 0xe9000000, 00:C0:F0:4A:CF:65, IRQ 10.
PCI: setting IRQ 11 as level-triggered
PCI: Found IRQ 11 for device 0000:00:09.0
SELinux: initialized (dev ramfs, type ramfs), uses genfs_contexts
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
Mobile IPv6
device-mapper: multipath: version 1.0.5 loaded
EXT3 FS on dm-0, internal journal
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev sda1, type ext3), uses xattr
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
Adding 1572856k swap on /dev/VolGroup00/LogVol01.  Priority:-1 extents:1 across:1572856k
SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses genfs_contexts
IA-32 Microcode Update Driver: v1.14a <tigran@aivazian.fsnet.co.uk>
ata1.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
ata1.01: (BMDMA stat 0x64)
ata1.01: cmd 35/00:00:6f:42:00/00:04:00:00:00/f0 tag 0 cdb 0x0 data 524288 out
         res 51/84:00:6f:42:00/84:00:00:00:00/f0 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1.00: configured for UDMA/66
ata1.01: configured for UDMA/44
ata1: EH complete
ata1.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
ata1.01: (BMDMA stat 0x64)
ata1.01: cmd 35/00:00:6f:42:00/00:04:00:00:00/f0 tag 0 cdb 0x0 data 524288 out
         res 51/84:00:6f:42:00/84:00:00:00:00/f0 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1.00: configured for UDMA/66
ata1.01: configured for UDMA/44
ata1: EH complete
sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:1:0: [sdb] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:1:0: [sdb] Write Protect is off
sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:1:0: [sdb] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:1:0: [sdb] Write Protect is off
sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
audit(1192415436.994:4): audit_pid=1315 old=0 by auid=4294967295 subj=system_u:system_r:auditd_t:s0
eth0: Setting half-duplex based on MII#1 link partner capability of 4021.
ata1.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
ata1.01: (BMDMA stat 0x64)
ata1.01: cmd ca/00:30:bf:01:98/00:00:00:00:00/f8 tag 0 cdb 0x0 data 24576 out
         res 51/84:00:bf:01:98/84:00:00:00:00/f8 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1.00: configured for UDMA/66
ata1.01: configured for UDMA/44
ata1: EH complete
sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:1:0: [sdb] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:1:0: [sdb] Write Protect is off
sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:1:0: [sdb] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:1:0: [sdb] Write Protect is off
sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
SELinux: initialized (dev rpc_pipefs, type rpc_pipefs), uses genfs_contexts
eth0: no IPv6 routers present
ip6_tables: (C) 2000-2006 Netfilter Core Team
ip_tables: (C) 2000-2006 Netfilter Core Team
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (6144 buckets, 49152 max)
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
ata1.01: limiting speed to UDMA/33:PIO4
ata1.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
ata1.01: (BMDMA stat 0x64)
ata1.01: cmd 35/00:60:87:7a:00/00:01:00:00:00/f0 tag 0 cdb 0x0 data 180224 out
         res 51/84:00:87:7a:00/84:00:00:00:00/f0 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1.00: configured for UDMA/66
ata1.01: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:1:0: [sdb] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:1:0: [sdb] Write Protect is off
sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:1:0: [sdb] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:1:0: [sdb] Write Protect is off
sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
ata1.01: (BMDMA stat 0x64)
ata1.01: cmd c8/00:88:a7:0a:fa/00:00:00:00:00/f4 tag 0 cdb 0x0 data 69632 in
         res 51/84:01:2e:0b:fa/84:00:00:00:00/f4 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1.00: configured for UDMA/66
ata1.01: configured for UDMA/33
ata1: EH complete
ata1.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
ata1.01: (BMDMA stat 0x64)
ata1.01: cmd c8/00:88:a7:0a:fa/00:00:00:00:00/f4 tag 0 cdb 0x0 data 69632 in
         res 51/84:01:2e:0b:fa/84:00:00:00:00/f4 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1.00: configured for UDMA/66
ata1.01: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
ata1.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
ata1.01: (BMDMA stat 0x64)
ata1.01: cmd c8/00:88:a7:0a:fa/00:00:00:00:00/f4 tag 0 cdb 0x0 data 69632 in
         res 51/84:01:2e:0b:fa/84:00:00:00:00/f4 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1.00: configured for UDMA/66
ata1.01: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:1:0: [sdb] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:1:0: [sdb] Write Protect is off
sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:1:0: [sdb] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:1:0: [sdb] Write Protect is off
sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
ata1.01: (BMDMA stat 0x64)
ata1.01: cmd c8/00:20:cf:41:43/00:00:00:00:00/f3 tag 0 cdb 0x0 data 16384 in
         res 51/84:01:ee:41:43/84:00:00:00:00/f3 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1.00: configured for UDMA/66
ata1.01: configured for UDMA/33
ata1: EH complete
ata1.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
ata1.01: (BMDMA stat 0x64)
ata1.01: cmd c8/00:20:cf:41:43/00:00:00:00:00/f3 tag 0 cdb 0x0 data 16384 in
         res 51/84:01:ee:41:43/84:00:00:00:00/f3 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1.00: configured for UDMA/66
ata1.01: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
ata1.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
ata1.01: (BMDMA stat 0x64)
ata1.01: cmd c8/00:20:cf:41:43/00:00:00:00:00/f3 tag 0 cdb 0x0 data 16384 in
         res 51/84:01:ee:41:43/84:00:00:00:00/f3 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1.00: configured for UDMA/66
ata1.01: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
ata1.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
ata1.01: (BMDMA stat 0x64)
ata1.01: cmd c8/00:20:cf:41:43/00:00:00:00:00/f3 tag 0 cdb 0x0 data 16384 in
         res 51/84:01:ee:41:43/84:00:00:00:00/f3 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1.00: configured for UDMA/66
ata1.01: configured for UDMA/33
ata1: EH complete
ata1.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
ata1.01: (BMDMA stat 0x64)
ata1.01: cmd c8/00:20:cf:41:43/00:00:00:00:00/f3 tag 0 cdb 0x0 data 16384 in
         res 51/84:01:ee:41:43/84:00:00:00:00/f3 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1.00: configured for UDMA/66
ata1.01: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
ata1.01: (BMDMA stat 0x64)
ata1.01: cmd c8/00:20:cf:41:43/00:00:00:00:00/f3 tag 0 cdb 0x0 data 16384 in
         res 51/84:01:ee:41:43/84:00:00:00:00/f3 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1.00: configured for UDMA/66
ata1.01: configured for UDMA/33
sd 0:0:1:0: [sdb] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK
sd 0:0:1:0: [sdb] Sense Key : Aborted Command [current] [descriptor]
Descriptor sense data with sense descriptors (in hex):
        72 0b 47 00 00 00 00 0c 00 0a 80 00 00 00 00 00 
        03 43 41 ee 
sd 0:0:1:0: [sdb] Add. Sense: Scsi parity error
end_request: I/O error, dev sdb, sector 54739407
ata1: EH complete
sd 0:0:1:0: [sdb] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:1:0: [sdb] Write Protect is off
sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:1:0: [sdb] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:1:0: [sdb] Write Protect is off
sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
ata1.01: (BMDMA stat 0x64)
ata1.01: cmd c8/00:08:e7:41:43/00:00:00:00:00/f3 tag 0 cdb 0x0 data 4096 in
         res 51/84:01:ee:41:43/84:00:00:00:00/f3 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1.00: configured for UDMA/66
ata1.01: configured for UDMA/33
ata1: EH complete
ata1.01: limiting speed to PIO4
ata1.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
ata1.01: (BMDMA stat 0x64)
ata1.01: cmd c8/00:08:e7:41:43/00:00:00:00:00/f3 tag 0 cdb 0x0 data 4096 in
         res 51/84:01:ee:41:43/84:00:00:00:00/f3 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1.00: configured for UDMA/66
ata1.01: configured for PIO4
ata1: EH complete
sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:1:0: [sdb] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:1:0: [sdb] Write Protect is off
sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:1:0: [sdb] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:1:0: [sdb] Write Protect is off
sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Clocksource tsc unstable (delta = 143851066 ns)
Time: pit clocksource has been installed.
spurious 8259A interrupt: IRQ7.
