Linux version 2.6.23-0.73.rc2.fc8 (kojibuilder@xenbuilder4.fedora.phx.redhat.com) (gcc version 4.1.2 20070723 (Red Hat 4.1.2-17)) #1 SMP Mon Aug 6 20:26:04 EDT 2007 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009e400 (usable) BIOS-e820: 000000000009e400 - 00000000000a0000 (reserved) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000003fff0000 (usable) BIOS-e820: 000000003fff0000 - 000000003fff3000 (ACPI NVS) BIOS-e820: 000000003fff3000 - 0000000040000000 (ACPI data) BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved) BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved) 127MB HIGHMEM available. 896MB LOWMEM available. found SMP MP-table at 000f58d0 Using x86 segment limits to approximate NX protection Entering add_active_range(0, 0, 262128) 0 entries of 256 used Zone PFN ranges: DMA 0 -> 4096 Normal 4096 -> 229376 HighMem 229376 -> 262128 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0 -> 262128 On node 0 totalpages: 262128 DMA zone: 56 pages used for memmap DMA zone: 0 pages reserved DMA zone: 4040 pages, LIFO batch:0 Normal zone: 3080 pages used for memmap Normal zone: 222200 pages, LIFO batch:31 HighMem zone: 447 pages used for memmap HighMem zone: 32305 pages, LIFO batch:7 Movable zone: 0 pages used for memmap DMI 2.3 present. Using APIC driver default ACPI: RSDP 000F7C80, 0014 (r0 Nvidia) ACPI: RSDT 3FFF3040, 0034 (r1 Nvidia AWRDACPI 42302E31 AWRD 0) ACPI: FACP 3FFF30C0, 0074 (r1 Nvidia AWRDACPI 42302E31 AWRD 0) ACPI: DSDT 3FFF3180, 6677 (r1 NVIDIA AWRDACPI 1000 MSFT 100000E) ACPI: FACS 3FFF0000, 0040 ACPI: SRAT 3FFF9900, 0090 (r1 AMD HAMMER 1 AMD 1) ACPI: MCFG 3FFF9A00, 003C (r1 Nvidia AWRDACPI 42302E31 AWRD 0) ACPI: APIC 3FFF9840, 007C (r1 Nvidia AWRDACPI 42302E31 AWRD 0) Nvidia board detected. Ignoring ACPI timer override. If you got timer trouble try acpi_use_timer_override ACPI: PM-Timer IO Port: 0x4008 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) Processor #0 15:7 APIC version 16 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled) ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: BIOS IRQ0 pin2 override ignored. ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge) ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge) ACPI: IRQ9 used by override. ACPI: IRQ14 used by override. ACPI: IRQ15 used by override. Enabling APIC mode: Flat. Using 1 I/O APICs Using ACPI (MADT) for SMP configuration information Allocating PCI resources starting at 50000000 (gap: 40000000:a0000000) swsusp: Registered nosave memory region: 000000000009e000 - 000000000009f000 swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000 swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000f0000 swsusp: Registered nosave memory region: 00000000000f0000 - 0000000000100000 Built 1 zonelists in Zone order. Total pages: 258545 Kernel command line: ro root=LABEL=/ rhgb quiet mapped APIC to ffffb000 (fee00000) mapped IOAPIC to ffffa000 (fec00000) Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 CPU 0 irqstacks, hard=c0816000 soft=c07f6000 PID hash table entries: 4096 (order: 12, 16384 bytes) Detected 2613.448 MHz processor. spurious 8259A interrupt: IRQ7. Console: colour VGA+ 80x25 console [tty0] enabled Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar ... MAX_LOCKDEP_SUBCLASSES: 8 ... MAX_LOCK_DEPTH: 30 ... MAX_LOCKDEP_KEYS: 2048 ... CLASSHASH_SIZE: 1024 ... MAX_LOCKDEP_ENTRIES: 8192 ... MAX_LOCKDEP_CHAINS: 16384 ... CHAINHASH_SIZE: 8192 memory used by lock dependency info: 1024 kB per task-struct memory footprint: 1680 bytes Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 1022384k/1048512k available (2239k kernel code, 25408k reserved, 1215k data, 568k init, 131008k highmem) virtual kernel memory layout: fixmap : 0xffc53000 - 0xfffff000 (3760 kB) pkmap : 0xff800000 - 0xffc00000 (4096 kB) vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB) lowmem : 0xc0000000 - 0xf8000000 ( 896 MB) .init : 0xc0765000 - 0xc07f3000 ( 568 kB) .data : 0xc062fd3d - 0xc075fa44 (1215 kB) .text : 0xc0400000 - 0xc062fd3d (2239 kB) Checking if this processor honours the WP bit even in supervisor mode... Ok. SLUB: Genslabs=22, HWalign=64, Order=0-1, MinObjects=4, CPUs=1, Nodes=1 Calibrating delay using timer specific routine.. 5229.49 BogoMIPS (lpj=2614746) Security Framework v1.0.0 initialized SELinux: Initializing. SELinux: Starting in permissive mode selinux_register_security: Registering secondary module capability Capability LSM initialized as secondary Mount-cache hash table entries: 512 CPU: After generic identify, caps: 078bfbff e1d3fbff 00000000 00000000 00000000 00000000 00000000 00000000 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 1024K (64 bytes/line) CPU: After all inits, caps: 078bf3ff e1d3fbff 00000000 00000410 00000000 00000000 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. Compat vDSO mapped to ffffe000. Checking 'hlt' instruction... OK. SMP alternatives: switching to UP code Freeing SMP alternatives: 12k freed ACPI: Core revision 20070126 CPU0: AMD Athlon(tm) 64 FX-55 Processor stepping 0a Total of 1 processors activated (5229.49 BogoMIPS). ENABLING IO-APIC IRQs ..TIMER: vector=0x31 apic1=0 pin1=0 apic2=-1 pin2=-1 Brought up 1 CPUs sizeof(vma)=84 bytes sizeof(page)=56 bytes sizeof(inode)=604 bytes sizeof(dentry)=160 bytes sizeof(ext3inode)=856 bytes sizeof(buffer_head)=56 bytes sizeof(skbuff)=180 bytes sizeof(task_struct)=3376 bytes khelper used greatest stack depth: 3160 bytes left Booting paravirtualized kernel on bare hardware khelper used greatest stack depth: 3084 bytes left Time: 23:26:39 Date: 07/09/107 NET: Registered protocol family 16 ACPI: bus type pci registered PCI: Using MMCONFIG PCI: No mmconfig possible on device 00:18 Setting up standard PCI resources ACPI: Interpreter enabled ACPI: (supports S0 S1 S3) ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Transparent bridge - 0000:00:09.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT] ACPI: PCI Interrupt Link [LNK1] (IRQs *3 4 5 7 9 10 11 12 14 15) ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNK3] (IRQs 3 4 5 7 9 10 *11 12 14 15) ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 *5 7 9 10 11 12 14 15) ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LUBA] (IRQs *3 4 5 7 9 10 11 12 14 15) ACPI: PCI Interrupt Link [LUBB] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LMAC] (IRQs 3 4 *5 7 9 10 11 12 14 15) ACPI: PCI Interrupt Link [LACI] (IRQs 3 4 5 7 9 10 11 *12 14 15) ACPI: PCI Interrupt Link [LMCI] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LSMB] (IRQs 3 4 5 7 9 10 11 *12 14 15) ACPI: PCI Interrupt Link [LUB2] (IRQs 3 4 5 7 9 10 *11 12 14 15) ACPI: PCI Interrupt Link [LIDE] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LSID] (IRQs 3 4 5 7 9 10 *11 12 14 15) ACPI: PCI Interrupt Link [LFID] (IRQs 3 4 *5 7 9 10 11 12 14 15) ACPI: PCI Interrupt Link [LPCA] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0 ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0, disabled. ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0 ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0 ACPI: PCI Interrupt Link [APC5] (IRQs *16), disabled. ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0 ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0 ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22 23) *0 ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0 ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0 ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0 ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0 ACPI: PCI Interrupt Link [APCP] (IRQs 20 21 22 23) *0, disabled. Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init ACPI: bus type pnp registered pnp: PnP ACPI: found 14 devices ACPI: ACPI bus type pnp unregistered usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report NetLabel: Initializing NetLabel: domain hash size = 128 NetLabel: protocols = UNLABELED CIPSOv4 NetLabel: unlabeled traffic allowed by default ACPI: RTC can wake from S4 Time: tsc clocksource has been installed. pnp: 00:01: ioport range 0x4000-0x407f has been reserved pnp: 00:01: ioport range 0x4080-0x40ff has been reserved pnp: 00:01: ioport range 0x4400-0x447f has been reserved pnp: 00:01: ioport range 0x4480-0x44ff has been reserved pnp: 00:01: ioport range 0x4800-0x487f has been reserved pnp: 00:01: ioport range 0x4880-0x48ff has been reserved pnp: 00:01: iomem range 0x0-0x0 could not be reserved pnp: 00:0c: iomem range 0xe0000000-0xefffffff could not be reserved pnp: 00:0d: iomem range 0xd9000-0xdbfff has been reserved pnp: 00:0d: iomem range 0xf0000-0xf7fff could not be reserved pnp: 00:0d: iomem range 0xf8000-0xfbfff could not be reserved pnp: 00:0d: iomem range 0xfc000-0xfffff could not be reserved PCI: Bridge: 0000:00:09.0 IO window: 8000-9fff MEM window: d3000000-d4ffffff PREFETCH window: 50000000-500fffff PCI: Bridge: 0000:00:0b.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:0c.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:0d.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:0e.0 IO window: a000-afff MEM window: d0000000-d2ffffff PREFETCH window: c0000000-cfffffff PCI: Setting latency timer of device 0000:00:09.0 to 64 PCI: Setting latency timer of device 0000:00:0b.0 to 64 PCI: Setting latency timer of device 0000:00:0c.0 to 64 PCI: Setting latency timer of device 0000:00:0d.0 to 64 PCI: Setting latency timer of device 0000:00:0e.0 to 64 NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 5, 131072 bytes) TCP established hash table entries: 65536 (order: 9, 2621440 bytes) TCP bind hash table entries: 65536 (order: 9, 2359296 bytes) TCP: Hash tables configured (established 65536 bind 65536) TCP reno registered checking if image is initramfs... it is Freeing initrd memory: 2955k freed khelper used greatest stack depth: 2872 bytes left apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac) apm: overridden by ACPI. audit: initializing netlink socket (disabled) audit(1186701999.674:1): initialized highmem bounce pool size: 64 pages Total HugeTLB memory allocated, 0 khelper used greatest stack depth: 2864 bytes left VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) SELinux: Registering netfilter hooks ksign: Installing public key data Loading keyring - Added public key 843EEBF3F06B1BE - User ID: Red Hat, Inc. (Kernel Module GPG key) io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) PCI: Found disabled HT MSI Mapping on 0000:00:0b.0 PCI: Found enabled HT MSI Mapping on 0000:00:00.0 PCI: Linking AER extended capability on 0000:00:0b.0 PCI: Found disabled HT MSI Mapping on 0000:00:0c.0 PCI: Found enabled HT MSI Mapping on 0000:00:00.0 PCI: Linking AER extended capability on 0000:00:0c.0 PCI: Found disabled HT MSI Mapping on 0000:00:0d.0 PCI: Found enabled HT MSI Mapping on 0000:00:00.0 PCI: Linking AER extended capability on 0000:00:0d.0 PCI: Found disabled HT MSI Mapping on 0000:00:0e.0 PCI: Found enabled HT MSI Mapping on 0000:00:00.0 PCI: Linking AER extended capability on 0000:00:0e.0 Boot video device is 0000:01:00.0 PCI: Setting latency timer of device 0000:00:0b.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:0b.0:pcie00] Allocate Port Service[0000:00:0b.0:pcie03] PCI: Setting latency timer of device 0000:00:0c.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:0c.0:pcie00] Allocate Port Service[0000:00:0c.0:pcie03] PCI: Setting latency timer of device 0000:00:0d.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:0d.0:pcie00] Allocate Port Service[0000:00:0d.0:pcie03] PCI: Setting latency timer of device 0000:00:0e.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:0e.0:pcie00] Allocate Port Service[0000:00:0e.0:pcie03] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 ACPI: Fan [FAN] (on) ACPI Exception (processor_core-0790): AE_NOT_FOUND, Processor Device is not present [20070126] ACPI: Thermal Zone [THRM] (40 C) isapnp: Scanning for PnP cards... Switched to high resolution mode on CPU 0 isapnp: No Plug & Play device found khelper used greatest stack depth: 2796 bytes left Generic RTC Driver v1.07 Non-volatile memory driver v1.2 Linux agpgart interface v0.102 Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A RAMDISK driver initialized: 16 RAM disks of 16384K size 4096 blocksize input: Macintosh mouse button emulation as /class/input/input0 PNP: No PS/2 controller found. Probing ports directly. serio: i8042 KBD port at 0x60,0x64 irq 1 mice: PS/2 mouse device common for all mice usbcore: registered new interface driver hiddev usbcore: registered new interface driver usbhid drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver TCP cubic registered Initializing XFRM netlink socket NET: Registered protocol family 1 NET: Registered protocol family 17 powernow-k8: Found 1 AMD Athlon(tm) 64 FX-55 Processor processors (1 cpu cores) (version 2.00.00) powernow-k8: BIOS error - no PSB or ACPI _PSS objects Using IPI No-Shortcut mode Magic number: 3:503:453 drivers/rtc/hctosys.c: unable to open rtc device (rtc0) Freeing unused kernel memory: 568k freed Write protecting the kernel read-only data: 916k USB Universal Host Controller Interface driver v3.0 insmod used greatest stack depth: 2312 bytes left ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver ACPI: PCI Interrupt Link [APCF] enabled at IRQ 23 ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [APCF] -> GSI 23 (level, low) -> IRQ 16 PCI: Setting latency timer of device 0000:00:02.0 to 64 ohci_hcd 0000:00:02.0: OHCI Host Controller ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1 ohci_hcd 0000:00:02.0: irq 16, io mem 0xd5004000 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 10 ports detected insmod used greatest stack depth: 1912 bytes left ACPI: PCI Interrupt Link [APCL] enabled at IRQ 22 ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [APCL] -> GSI 22 (level, low) -> IRQ 17 PCI: Setting latency timer of device 0000:00:02.1 to 64 ehci_hcd 0000:00:02.1: EHCI Host Controller ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 2 ehci_hcd 0000:00:02.1: debug port 1 PCI: cache line size of 64 is not supported by device 0000:00:02.1 ehci_hcd 0000:00:02.1: irq 17, io mem 0xfeb00000 ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 10 ports detected insmod used greatest stack depth: 1892 bytes left SCSI subsystem initialized libata version 2.21 loaded. sata_sil 0000:05:0a.0: version 2.2 ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19 ACPI: PCI Interrupt 0000:05:0a.0[A] -> Link [APC4] -> GSI 19 (level, low) -> IRQ 18 sata_sil 0000:05:0a.0: Applying R_ERR on DMA activate FIS errata fix scsi0 : sata_sil scsi1 : sata_sil scsi2 : sata_sil scsi3 : sata_sil ata1: SATA max UDMA/100 cmd 0xf8824080 ctl 0xf882408a bmdma 0xf8824000 irq 18 ata2: SATA max UDMA/100 cmd 0xf88240c0 ctl 0xf88240ca bmdma 0xf8824008 irq 18 ata3: SATA max UDMA/100 cmd 0xf8824280 ctl 0xf882428a bmdma 0xf8824200 irq 18 ata4: SATA max UDMA/100 cmd 0xf88242c0 ctl 0xf88242ca bmdma 0xf8824208 irq 18 ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) ata1.00: ATA-7: WDC WD360ADFD-00NLR1, 20.07P20, max UDMA/133 ata1.00: 72303840 sectors, multi 16: LBA48 NCQ (depth 0/32) ata1.00: configured for UDMA/100 ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) ata2.00: ATA-7: WDC WD360ADFD-00NLR1, 20.07P20, max UDMA/133 ata2.00: 72303840 sectors, multi 16: LBA48 NCQ (depth 0/32) ata2.00: configured for UDMA/100 usb 2-4: new high speed USB device using ehci_hcd and address 5 usb 2-4: configuration #1 chosen from 1 choice hub 2-4:1.0: USB hub found hub 2-4:1.0: 4 ports detected ata3: SATA link down (SStatus 0 SControl 310) ata4: SATA link down (SStatus 0 SControl 310) scsi 0:0:0:0: Direct-Access ATA WDC WD360ADFD-00 20.0 PQ: 0 ANSI: 5 sd 0:0:0:0: [sda] 72303840 512-byte hardware sectors (37020 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 0:0:0:0: [sda] 72303840 512-byte hardware sectors (37020 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 < > sda: p1 exceeds device capacity sda: p2 exceeds device capacity sd 0:0:0:0: [sda] Attached SCSI disk scsi 1:0:0:0: Direct-Access ATA WDC WD360ADFD-00 20.0 PQ: 0 ANSI: 5 sd 1:0:0:0: [sdb] 72303840 512-byte hardware sectors (37020 MB) sd 1:0:0:0: [sdb] Write Protect is off sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 1:0:0:0: [sdb] 72303840 512-byte hardware sectors (37020 MB) sd 1:0:0:0: [sdb] Write Protect is off sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sdb: unknown partition table sd 1:0:0:0: [sdb] Attached SCSI disk insmod used greatest stack depth: 940 bytes left usb 1-1: new full speed USB device using ohci_hcd and address 2 usb 1-1: configuration #1 chosen from 1 choice input: Logitech USB Gaming Mouse as /class/input/input1 input: USB HID v1.11 Mouse [Logitech USB Gaming Mouse] on usb-0000:00:02.0-1 hiddev96: USB HID v1.11 Device [Logitech USB Gaming Mouse] on usb-0000:00:02.0-1 usb 1-2: new full speed USB device using ohci_hcd and address 3 usb 1-2: configuration #1 chosen from 1 choice hub 1-2:1.0: USB hub found hub 1-2:1.0: 4 ports detected usb 1-3: new full speed USB device using ohci_hcd and address 4 usb 1-3: configuration #1 chosen from 1 choice input: Logitech Logitech USB Headset as /class/input/input2 input: USB HID v1.00 Device [Logitech Logitech USB Headset] on usb-0000:00:02.0-3 usb 2-4.3: new high speed USB device using ehci_hcd and address 6 usb 2-4.3: configuration #1 chosen from 1 choice usb 2-4.4: new full speed USB device using ehci_hcd and address 7 usb 2-4.4: configuration #1 chosen from 1 choice usb 1-2.1: new low speed USB device using ohci_hcd and address 5 usb 1-2.1: configuration #1 chosen from 1 choice input: Logitech Logitech Gaming Keyboard as /class/input/input3 input: USB HID v1.10 Keyboard [Logitech Logitech Gaming Keyboard] on usb-0000:00:02.0-2.1 input: Logitech Logitech Gaming Keyboard as /class/input/input4 input,hiddev97: USB HID v1.10 Device [Logitech Logitech Gaming Keyboard] on usb-0000:00:02.0-2.1 usb 1-2.4: new full speed USB device using ohci_hcd and address 6 usb 1-2.4: configuration #1 chosen from 1 choice input: G15 Keyboard G15 Keyboard as /class/input/input5 input,hiddev98: USB HID v1.11 Keypad [G15 Keyboard G15 Keyboard] on usb-0000:00:02.0-2.4 sata_nv 0000:00:07.0: version 3.4 ACPI: PCI Interrupt Link [APSI] enabled at IRQ 21 ACPI: PCI Interrupt 0000:00:07.0[A] -> Link [APSI] -> GSI 21 (level, low) -> IRQ 19 sata_nv 0000:00:07.0: Using ADMA mode PCI: Setting latency timer of device 0000:00:07.0 to 64 scsi4 : sata_nv scsi5 : sata_nv ata5: SATA max UDMA/133 cmd 0xf8826480 ctl 0xf88264a0 bmdma 0x0001d800 irq 19 ata6: SATA max UDMA/133 cmd 0xf8826580 ctl 0xf88265a0 bmdma 0x0001d808 irq 19 ata5: SATA link down (SStatus 0 SControl 300) ata6: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata6.00: ATA-7: ST3250824AS, 3.AAE, max UDMA/133 ata6.00: 488397168 sectors, multi 1: LBA48 NCQ (depth 31/32) ata6.00: configured for UDMA/133 scsi 5:0:0:0: Direct-Access ATA ST3250824AS 3.AA PQ: 0 ANSI: 5 ata6: bounce limit 0xFFFFFFFFFFFFFFFF, segment boundary 0xFFFFFFFF, hw segs 61 sd 5:0:0:0: [sdc] 488397168 512-byte hardware sectors (250059 MB) sd 5:0:0:0: [sdc] Write Protect is off sd 5:0:0:0: [sdc] Mode Sense: 00 3a 00 00 sd 5:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 5:0:0:0: [sdc] 488397168 512-byte hardware sectors (250059 MB) sd 5:0:0:0: [sdc] Write Protect is off sd 5:0:0:0: [sdc] Mode Sense: 00 3a 00 00 sd 5:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sdc: sdc1 sdc2 sdc3 < sdc5 > sd 5:0:0:0: [sdc] Attached SCSI disk ACPI: PCI Interrupt Link [APSJ] enabled at IRQ 20 ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [APSJ] -> GSI 20 (level, low) -> IRQ 20 sata_nv 0000:00:08.0: Using ADMA mode PCI: Setting latency timer of device 0000:00:08.0 to 64 scsi6 : sata_nv scsi7 : sata_nv ata7: SATA max UDMA/133 cmd 0xf8842480 ctl 0xf88424a0 bmdma 0x0001c400 irq 20 ata8: SATA max UDMA/133 cmd 0xf8842580 ctl 0xf88425a0 bmdma 0x0001c408 irq 20 ata7: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata7.00: ATA-7: ST3300622AS, 3.AAH, max UDMA/133 ata7.00: 586072368 sectors, multi 1: LBA48 NCQ (depth 31/32) ata7.00: configured for UDMA/133 ata8: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata8.00: ATA-7: ST3250823AS, 3.03, max UDMA/133 ata8.00: 488397168 sectors, multi 1: LBA48 NCQ (depth 31/32) ata8.00: configured for UDMA/133 scsi 6:0:0:0: Direct-Access ATA ST3300622AS 3.AA PQ: 0 ANSI: 5 ata7: bounce limit 0xFFFFFFFFFFFFFFFF, segment boundary 0xFFFFFFFF, hw segs 61 sd 6:0:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB) sd 6:0:0:0: [sdd] Write Protect is off sd 6:0:0:0: [sdd] Mode Sense: 00 3a 00 00 sd 6:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 6:0:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB) sd 6:0:0:0: [sdd] Write Protect is off sd 6:0:0:0: [sdd] Mode Sense: 00 3a 00 00 sd 6:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sdd: sdd1 sd 6:0:0:0: [sdd] Attached SCSI disk scsi 7:0:0:0: Direct-Access ATA ST3250823AS 3.03 PQ: 0 ANSI: 5 ata8: bounce limit 0xFFFFFFFFFFFFFFFF, segment boundary 0xFFFFFFFF, hw segs 61 sd 7:0:0:0: [sde] 488397168 512-byte hardware sectors (250059 MB) sd 7:0:0:0: [sde] Write Protect is off sd 7:0:0:0: [sde] Mode Sense: 00 3a 00 00 sd 7:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 7:0:0:0: [sde] 488397168 512-byte hardware sectors (250059 MB) sd 7:0:0:0: [sde] Write Protect is off sd 7:0:0:0: [sde] Mode Sense: 00 3a 00 00 sd 7:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sde: sde1 sde2 sd 7:0:0:0: [sde] Attached SCSI disk pata_amd 0000:00:06.0: version 0.3.8 PCI: Setting latency timer of device 0000:00:06.0 to 64 scsi8 : pata_amd scsi9 : pata_amd ata9: PATA max UDMA/133 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x0001f000 irq 14 ata10: PATA max UDMA/133 cmd 0x00010170 ctl 0x00010376 bmdma 0x0001f008 irq 15 ata9.00: ATAPI: _NEC DVD_RW ND-3550A, 1.05, max UDMA/33 ata9.00: configured for UDMA/33 scsi 8:0:0:0: CD-ROM _NEC DVD_RW ND-3550A 1.05 PQ: 0 ANSI: 5 device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. SELinux: Disabled at runtime. SELinux: Unregistering netfilter hooks audit(1186702014.306:2): selinux=0 auid=4294967295 sd 0:0:0:0: Attached scsi generic sg0 type 0 sd 1:0:0:0: Attached scsi generic sg1 type 0 sd 5:0:0:0: Attached scsi generic sg2 type 0 sd 6:0:0:0: Attached scsi generic sg3 type 0 sd 7:0:0:0: Attached scsi generic sg4 type 0 scsi 8:0:0:0: Attached scsi generic sg5 type 5 Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 sr0: scsi3-mmc drive: 48x/48x writer cd/rw xa/form2 cdda tray Uniform CD-ROM driver Revision: 3.20 sr 8:0:0:0: Attached scsi CD-ROM sr0 input: Power Button (FF) as /class/input/input6 ACPI: Power Button (FF) [PWRF] input: Power Button (CM) as /class/input/input7 ACPI: Power Button (CM) [PWRB] i2c-adapter i2c-0: nForce2 SMBus adapter at 0x4c00 i2c-adapter i2c-1: nForce2 SMBus adapter at 0x4c40 forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.60. ACPI: PCI Interrupt Link [APCH] enabled at IRQ 23 ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [APCH] -> GSI 23 (level, low) -> IRQ 16 PCI: Setting latency timer of device 0000:00:0a.0 to 64 forcedeth: using HIGHDMA eth0: forcedeth.c: subsystem: 01043:8141 bound to 0000:00:0a.0 ACPI: PCI Interrupt Link [APC1] enabled at IRQ 16 ACPI: PCI Interrupt 0000:05:0b.0[A] -> Link [APC1] -> GSI 16 (level, low) -> IRQ 21 firewire_ohci: Added fw-ohci device 0000:05:0b.0, OHCI version 1.10 rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0 rtc0: alarms up to one year, y3k usbcore: registered new interface driver snd-usb-audio usblp0: USB Bidirectional printer dev 6 if 0 alt 0 proto 2 vid 0x03F0 pid 0x2B17 usbcore: registered new interface driver usblp firewire_core: created new fw device fw0 (0 config rom retries, S400) parport_pc 00:09: reported by Plug and Play ACPI parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE] cannot find the slot for index 0 (range 0-1), error: -16 Intel ICH: probe of 0000:00:04.0 failed with error -12 gameport: NS558 PnP Gameport is pnp00:0b/gameport0, io 0x201, speed 59659kHz nvidia: module license 'NVIDIA' taints kernel. ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18 ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [APC3] -> GSI 18 (level, low) -> IRQ 22 PCI: Setting latency timer of device 0000:01:00.0 to 64 NVRM: loading NVIDIA UNIX x86 Kernel Module 100.14.11 Wed Jun 13 18:21:22 PDT 2007 NET: Registered protocol family 10 lo: Disabled Privacy Extensions No dock devices found. device-mapper: multipath: version 1.0.5 loaded EXT3 FS on dm-3, internal journal kjournald starting. Commit interval 5 seconds EXT3 FS on sde1, internal journal EXT3-fs: mounted filesystem with ordered data mode. Adding 2128572k swap on /dev/mapper/sil_ahagdiddaiajp6. Priority:-1 extents:1 across:2128572k audit(1186716432.323:3): audit_pid=2189 old=0 by auid=4294967295 Bluetooth: Core ver 2.11 NET: Registered protocol family 31 Bluetooth: HCI device and connection manager initialized Bluetooth: HCI socket layer initialized Bluetooth: L2CAP ver 2.8 Bluetooth: L2CAP socket layer initialized Bluetooth: RFCOMM socket layer initialized Bluetooth: RFCOMM TTY layer initialized Bluetooth: RFCOMM ver 1.8 ppdev: user-space parallel port driver ppdev0: registered pardevice ppdev0: unregistered pardevice ppdev0: registered pardevice ppdev0: unregistered pardevice eth0: no IPv6 routers present lp0: using parport0 (interrupt-driven). lp0: console ready eog[4885]: segfault at 00000000 eip 006b3683 esp b7cfcfcc error 4 eog[4891]: segfault at 00000000 eip 006b3683 esp b7db9fcc error 4 eog[6062]: segfault at 00000000 eip 006b3683 esp b7d5efcc error 4