Linux version 2.6.23-0.184.rc6.git4.fc8 (kojibuilder@) (gcc version 4.1.2 20070821 (Red Hat 4.1.2-23)) #1 SMP Fri Sep 14 17:11:26 EDT 2007 Command line: ro root=/dev/VolGroup00/LogVol00 rhgb quiet BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009e000 (usable) BIOS-e820: 000000000009e000 - 00000000000a0000 (reserved) BIOS-e820: 00000000000d2000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000007bf50000 (usable) BIOS-e820: 000000007bf50000 - 000000007bf65000 (ACPI data) BIOS-e820: 000000007bf65000 - 000000007bf66000 (ACPI NVS) BIOS-e820: 000000007bf66000 - 0000000080000000 (reserved) BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved) BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved) Entering add_active_range(0, 0, 158) 0 entries of 3200 used Entering add_active_range(0, 256, 507728) 1 entries of 3200 used end_pfn_map = 1048576 DMI present. ACPI: RSDP 000F8250, 0024 (r2 PTLTD ) ACPI: XSDT 7BF5C5E6, 006C (r1 HPQOEM SLIC-MPC 6040000 LTP 0) ACPI: FACP 7BF649BA, 00F4 (r3 NVIDIA MCP67-M 6040000 PTL_ F4240) ACPI: DSDT 7BF5C652, 82F4 (r1 NVIDIA MCP67 6040000 MSFT 3000000) ACPI: FACS 7BF65FC0, 0040 ACPI: TCPA 7BF64AAE, 0032 (r1 Phoeni x 6040000 TL 0) ACPI: SRAT 7BF64AE0, 00A0 (r1 AMD HAMMER 6040000 AMD 1) ACPI: SSDT 7BF64B80, 0206 (r1 PTLTD POWERNOW 6040000 LTP 1) ACPI: MCFG 7BF64D86, 003C (r1 PTLTD MCFG 6040000 LTP 0) ACPI: HPET 7BF64DC2, 0038 (r1 PTLTD HPETTBL 6040000 LTP 1) ACPI: APIC 7BF64DFA, 0068 (r1 PTLTD APIC 6040000 LTP 0) ACPI: BOOT 7BF64E62, 0028 (r1 PTLTD $SBFTBL$ 6040000 LTP 1) ACPI: SLIC 7BF64E8A, 0176 (r1 HPQOEM SLIC-MPC 6040000 LTP 1) SRAT: PXM 0 -> APIC 0 -> Node 0 SRAT: PXM 0 -> APIC 1 -> Node 0 SRAT: Node 0 PXM 0 0-a0000 Entering add_active_range(0, 0, 158) 0 entries of 3200 used SRAT: Node 0 PXM 0 0-80000000 Entering add_active_range(0, 0, 158) 1 entries of 3200 used Entering add_active_range(0, 256, 507728) 1 entries of 3200 used NUMA: Using 63 for the hash shift. Bootmem setup node 0 0000000000000000-000000007bf50000 Zone PFN ranges: DMA 0 -> 4096 DMA32 4096 -> 1048576 Normal 1048576 -> 1048576 Movable zone start PFN for each node early_node_map[2] active PFN ranges 0: 0 -> 158 0: 256 -> 507728 On node 0 totalpages: 507630 DMA zone: 96 pages used for memmap DMA zone: 2497 pages reserved DMA zone: 1405 pages, LIFO batch:0 DMA32 zone: 11803 pages used for memmap DMA32 zone: 491829 pages, LIFO batch:31 Normal zone: 0 pages used for memmap Movable zone: 0 pages used for memmap ACPI: PM-Timer IO Port: 0x1008 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) Processor #0 (Bootup-CPU) ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled) Processor #1 ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 2, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level) ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: IRQ0 used by override. ACPI: IRQ2 used by override. ACPI: IRQ9 used by override. Setting APIC routing to flat ACPI: HPET id: 0x10de8201 base: 0xfed00000 Using ACPI (MADT) for SMP configuration information swsusp: Registered nosave memory region: 000000000009e000 - 00000000000a0000 swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000d2000 swsusp: Registered nosave memory region: 00000000000d2000 - 0000000000100000 Allocating PCI resources starting at 88000000 (gap: 80000000:60000000) SMP: Allowing 2 CPUs, 0 hotplug CPUs PERCPU: Allocating 435856 bytes of per cpu data Built 1 zonelists in Node order. Total pages: 493234 Policy zone: DMA32 Kernel command line: ro root=/dev/VolGroup00/LogVol00 rhgb quiet Initializing CPU#0 PID hash table entries: 4096 (order: 12, 32768 bytes) Extended CMOS year: 2000 hpet clockevent registered TSC calibrated against HPET Marking TSC unstable due to TSCs unsynchronized time.c: Detected 1900.176 MHz processor. Console: colour VGA+ 80x25 console [tty0] enabled Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar ... MAX_LOCKDEP_SUBCLASSES: 8 ... MAX_LOCK_DEPTH: 30 ... MAX_LOCKDEP_KEYS: 2048 ... CLASSHASH_SIZE: 1024 ... MAX_LOCKDEP_ENTRIES: 8192 ... MAX_LOCKDEP_CHAINS: 16384 ... CHAINHASH_SIZE: 8192 memory used by lock dependency info: 1712 kB per task-struct memory footprint: 2160 bytes Checking aperture... CPU 0: aperture @ 9022000000 size 32 MB Aperture too small (32 MB) No AGP bridge found Memory: 1966404k/2030912k available (2500k kernel code, 64116k reserved, 1443k data, 708k init) SLUB: Genslabs=23, HWalign=64, Order=0-1, MinObjects=4, CPUs=2, Nodes=1 Calibrating delay using timer specific routine.. 3804.15 BogoMIPS (lpj=1902077) Security Framework v1.0.0 initialized SELinux: Initializing. SELinux: Starting in permissive mode selinux_register_security: Registering secondary module capability Capability LSM initialized as secondary Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes) Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes) Mount-cache hash table entries: 256 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 512K (64 bytes/line) CPU 0/0 -> Node 0 CPU: Physical Processor ID: 0 CPU: Processor Core ID: 0 lockdep: not fixing up alternatives. ACPI: Core revision 20070126 Using local APIC timer interrupts. APIC timer calibration result 12501161 Detected 12.501 MHz APIC timer. lockdep: not fixing up alternatives. Booting processor 1/2 APIC 0x1 Initializing CPU#1 Calibrating delay using timer specific routine.. 3800.36 BogoMIPS (lpj=1900184) CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 512K (64 bytes/line) CPU 1/1 -> Node 0 CPU: Physical Processor ID: 0 CPU: Processor Core ID: 1 AMD Turion(tm) 64 X2 Mobile Technology TL-58 stepping 01 Brought up 2 CPUs sizeof(vma)=176 bytes sizeof(page)=96 bytes sizeof(inode)=1088 bytes sizeof(dentry)=256 bytes sizeof(ext3inode)=1488 bytes sizeof(buffer_head)=104 bytes sizeof(skbuff)=232 bytes sizeof(task_struct)=4448 bytes khelper used greatest stack depth: 6600 bytes left khelper used greatest stack depth: 6416 bytes left Time: 16:22:04 Date: 08/17/107 NET: Registered protocol family 16 No dock devices found. ACPI: bus type pci registered PCI: Using MMCONFIG at e0000000 - e04fffff PCI: No mmconfig possible on device 00:18 ACPI: EC: Look up EC in DSDT ACPI: System BIOS is requesting _OSI(Linux) ACPI: If "acpi_osi=Linux" works better, Please send dmidecode to linux-acpi@vger.kernel.org ACPI: Interpreter enabled ACPI: (supports S0 S3) ACPI: Using IOAPIC for interrupt routing ACPI: EC: GPE = 0x10, I/O: command/status = 0x66, data = 0x62 ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Transparent bridge - 0000:00:08.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.XVR1._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.XVR2._PRT] ACPI: PCI Interrupt Link [LNK1] (IRQs 5) *10 ACPI: PCI Interrupt Link [LNK2] (IRQs 7) *11 ACPI: PCI Interrupt Link [LNK3] (IRQs 10) *0, disabled. ACPI: PCI Interrupt Link [LNK4] (IRQs 11) *0, disabled. ACPI: PCI Interrupt Link [LK1E] (IRQs 16) *0, disabled. ACPI: PCI Interrupt Link [LK2E] (IRQs 17) *0, disabled. ACPI: PCI Interrupt Link [LK3E] (IRQs 18) *0, disabled. ACPI: PCI Interrupt Link [LK4E] (IRQs 19) *10 ACPI: PCI Interrupt Link [LSMB] (IRQs *10) ACPI: PCI Interrupt Link [LUS0] (IRQs 18) *11 ACPI: PCI Interrupt Link [LUS2] (IRQs 22) *7 ACPI: PCI Interrupt Link [LMAC] (IRQs 20) *11 ACPI: PCI Interrupt Link [LAZA] (IRQs 21) *10 ACPI: PCI Interrupt Link [LGPU] (IRQs 16) *10 ACPI: PCI Interrupt Link [LPID] (IRQs 22) *0, disabled. ACPI: PCI Interrupt Link [LSI0] (IRQs 23) *11 ACPI: PCI Interrupt Link [Z015] (IRQs 18) *5 ACPI: PCI Interrupt Link [Z016] (IRQs 22) *10 ACPI: PCI Interrupt Link [LPMU] (IRQs *11) Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init ACPI: bus type pnp registered pnp: PnP ACPI: found 12 devices ACPI: ACPI bus type pnp unregistered usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report NetLabel: Initializing NetLabel: domain hash size = 128 NetLabel: protocols = UNLABELED CIPSOv4 NetLabel: unlabeled traffic allowed by default hpet0: at MMIO 0xfed00000, IRQs 2, 8, 31 hpet0: 3 32-bit timers, 25000000 Hz ACPI: RTC can wake from S4 Time: hpet clocksource has been installed. Switched to high resolution mode on CPU 1 Switched to high resolution mode on CPU 0 pnp: 00:02: iomem range 0xe0000000-0xefffffff could not be reserved pnp: 00:03: ioport range 0x1000-0x107f has been reserved pnp: 00:03: ioport range 0x1080-0x10ff has been reserved pnp: 00:03: ioport range 0x1400-0x147f has been reserved pnp: 00:03: ioport range 0x1480-0x14ff has been reserved pnp: 00:03: ioport range 0x1800-0x187f has been reserved pnp: 00:03: ioport range 0x1880-0x18ff has been reserved pnp: 00:0b: iomem range 0xffc00000-0xffffffff could not be reserved pnp: 00:0b: iomem range 0xfec00000-0xfec00fff could not be reserved pnp: 00:0b: iomem range 0xfee00000-0xfeefffff could not be reserved pnp: 00:0b: iomem range 0xfed00000-0xfed00fff has been reserved PCI: Bridge: 0000:00:08.0 IO window: disabled. MEM window: f6100000-f61fffff PREFETCH window: disabled. PCI: Bridge: 0000:00:0c.0 IO window: 4000-4fff MEM window: f2000000-f3ffffff PREFETCH window: f0000000-f1ffffff PCI: Bridge: 0000:00:0d.0 IO window: disabled. MEM window: f6000000-f60fffff PREFETCH window: disabled. PCI: Setting latency timer of device 0000:00:08.0 to 64 PCI: Setting latency timer of device 0000:00:0c.0 to 64 PCI: Setting latency timer of device 0000:00:0d.0 to 64 NET: Registered protocol family 2 IP route cache hash table entries: 65536 (order: 7, 524288 bytes) TCP established hash table entries: 262144 (order: 12, 18874368 bytes) TCP bind hash table entries: 65536 (order: 10, 4194304 bytes) TCP: Hash tables configured (established 262144 bind 65536) TCP reno registered checking if image is initramfs... it is Freeing initrd memory: 3836k freed khelper used greatest stack depth: 6280 bytes left Simple Boot Flag at 0x36 set to 0x1 audit: initializing netlink socket (disabled) audit(1190046123.875:1): initialized Total HugeTLB memory allocated, 0 VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 512 (order 0, 4096 bytes) SELinux: Registering netfilter hooks ksign: Installing public key data Loading keyring - Added public key D837C87CD7FE42BE - User ID: Red Hat, Inc. (Kernel Module GPG key) Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252) io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) Boot video device is 0000:00:12.0 PCI: Setting latency timer of device 0000:00:0c.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:0c.0:pcie00] Allocate Port Service[0000:00:0c.0:pcie03] PCI: Setting latency timer of device 0000:00:0d.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:0d.0:pcie00] Allocate Port Service[0000:00:0d.0:pcie03] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3]) ACPI: Processor [CPU0] (supports 8 throttling states) ACPI Exception (processor_core-0798): AE_NOT_FOUND, Processor Device is not present [20070126] ACPI Exception (processor_core-0798): AE_NOT_FOUND, Processor Device is not present [20070126] cpuidle: driver acpi_idle failed to attach to cpu 1 ACPI Exception (thermal-0338): AE_BAD_DATA, No critical threshold [20070126] hpet_resources: 0xfed00000 is busy Generic RTC Driver v1.07 Non-volatile memory driver v1.2 Linux agpgart interface v0.102 Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled RAMDISK driver initialized: 16 RAM disks of 16384K size 4096 blocksize input: Macintosh mouse button emulation as /class/input/input0 PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSE0] at 0x60,0x64 irq 1,12 serio: i8042 KBD port at 0x60,0x64 irq 1 serio: i8042 AUX port at 0x60,0x64 irq 12 mice: PS/2 mouse device common for all mice input: AT Translated Set 2 keyboard as /class/input/input1 input: AT Translated Set 2 keyboard as /class/input/input2 cpuidle: using governor menu usbcore: registered new interface driver hiddev usbcore: registered new interface driver usbhid drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver TCP cubic registered Initializing XFRM netlink socket NET: Registered protocol family 1 NET: Registered protocol family 17 powernow-k8: Found 1 AMD Turion(tm) 64 X2 Mobile Technology TL-58 processors (2 cpu cores) (version 2.00.00) powernow-k8: 0 : fid 0xb (1900 MHz), vid 0x13 powernow-k8: 1 : fid 0xa (1800 MHz), vid 0x14 powernow-k8: 2 : fid 0x8 (1600 MHz), vid 0x15 powernow-k8: 3 : fid 0x0 (800 MHz), vid 0x1e Magic number: 7:814:388 drivers/rtc/hctosys.c: unable to open rtc device (rtc0) Freeing unused kernel memory: 708k freed Write protecting the kernel read-only data: 1040k ACPI: PCI Interrupt Link [LUS2] enabled at IRQ 22 ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [LUS2] -> GSI 22 (level, low) -> IRQ 22 PCI: Setting latency timer of device 0000:00:02.1 to 64 ehci_hcd 0000:00:02.1: EHCI Host Controller ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:02.1: debug port 1 PCI: cache line size of 64 is not supported by device 0000:00:02.1 ehci_hcd 0000:00:02.1: irq 22, io mem 0xf6489000 ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 7 ports detected ACPI: PCI Interrupt Link [Z016] enabled at IRQ 22 ACPI: PCI Interrupt 0000:00:04.1[B] -> Link [Z016] -> GSI 22 (level, low) -> IRQ 22 PCI: Setting latency timer of device 0000:00:04.1 to 64 ehci_hcd 0000:00:04.1: EHCI Host Controller ehci_hcd 0000:00:04.1: new USB bus registered, assigned bus number 2 ehci_hcd 0000:00:04.1: debug port 1 PCI: cache line size of 64 is not supported by device 0000:00:04.1 ehci_hcd 0000:00:04.1: irq 22, io mem 0xf6489400 ehci_hcd 0000:00:04.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected insmod used greatest stack depth: 5456 bytes left ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver ACPI: PCI Interrupt Link [LUS0] enabled at IRQ 18 ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LUS0] -> GSI 18 (level, low) -> IRQ 18 PCI: Setting latency timer of device 0000:00:02.0 to 64 ohci_hcd 0000:00:02.0: OHCI Host Controller ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 3 ohci_hcd 0000:00:02.0: irq 18, io mem 0xf6486000 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 7 ports detected ACPI: PCI Interrupt Link [Z015] enabled at IRQ 18 ACPI: PCI Interrupt 0000:00:04.0[A] -> Link [Z015] -> GSI 18 (level, low) -> IRQ 18 PCI: Setting latency timer of device 0000:00:04.0 to 64 ohci_hcd 0000:00:04.0: OHCI Host Controller ohci_hcd 0000:00:04.0: new USB bus registered, assigned bus number 4 ohci_hcd 0000:00:04.0: irq 18, io mem 0xf6487000 usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected USB Universal Host Controller Interface driver v3.0 SCSI subsystem initialized libata version 2.21 loaded. Synaptics Touchpad, model: 1, fw: 6.3, id: 0x1a0b1, caps: 0xa04713/0x200000 ahci 0000:00:09.0: version 2.3 ACPI: PCI Interrupt Link [LSI0] enabled at IRQ 23 ACPI: PCI Interrupt 0000:00:09.0[A] -> Link [LSI0] -> GSI 23 (level, low) -> IRQ 23 input: SynPS/2 Synaptics TouchPad as /class/input/input3 usb 3-2: new full speed USB device using ohci_hcd and address 2 usb 3-2: configuration #1 chosen from 1 choice usb 4-1: new full speed USB device using ohci_hcd and address 2 usb 4-1: configuration #1 chosen from 1 choice ahci 0000:00:09.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl IDE mode ahci 0000:00:09.0: flags: 64bit sntf led clo pmp pio slum part PCI: Setting latency timer of device 0000:00:09.0 to 64 scsi0 : ahci scsi1 : ahci scsi2 : ahci scsi3 : ahci ata1: SATA max UDMA/133 cmd 0xffffc20000348100 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 2301 ata2: SATA max UDMA/133 cmd 0xffffc20000348180 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 2301 ata3: SATA max UDMA/133 cmd 0xffffc20000348200 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 2301 ata4: SATA max UDMA/133 cmd 0xffffc20000348280 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 2301 ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata1.00: ATA-7: Hitachi HTS541616J9SA00, SB4OC7BP, max UDMA/100 ata1.00: 312581808 sectors, multi 16: LBA48 ata1.00: configured for UDMA/100 ata2: SATA link down (SStatus 0 SControl 300) ata3: SATA link down (SStatus 0 SControl 300) ata4: SATA link down (SStatus 0 SControl 300) scsi 0:0:0:0: Direct-Access ATA Hitachi HTS54161 SB4O PQ: 0 ANSI: 5 sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 sda3 sda4 < sda5 > sd 0:0:0:0: [sda] Attached SCSI disk insmod used greatest stack depth: 3592 bytes left pata_amd 0000:00:06.0: version 0.3.9 PCI: Setting latency timer of device 0000:00:06.0 to 64 scsi4 : pata_amd scsi5 : pata_amd ata5: PATA max UDMA/133 cmd 0x00000000000101f0 ctl 0x00000000000103f6 bmdma 0x00000000000130c0 irq 14 ata6: PATA max UDMA/133 cmd 0x0000000000010170 ctl 0x0000000000010376 bmdma 0x00000000000130c8 irq 15 ata5.00: ATAPI: MATSHITADVD-RAM UJ-851S, 1.50, max MWDMA2 ata5.00: configured for MWDMA2 ata6: port disabled. ignoring. scsi 4:0:0:0: CD-ROM MATSHITA DVD-RAM UJ-851S 1.50 PQ: 0 ANSI: 5 device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. audit(1190046134.114:2): enforcing=1 old_enforcing=0 auid=4294967295 security: 5 users, 11 roles, 2264 types, 108 bools, 1 sens, 1024 cats security: 67 classes, 225209 rules SELinux: Completing initialization. SELinux: Setting up existing superblocks. SELinux: initialized (dev dm-0, type ext3), uses xattr SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs SELinux: initialized (dev debugfs, type debugfs), uses genfs_contexts SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs SELinux: initialized (dev hugetlbfs, type hugetlbfs), uses genfs_contexts SELinux: initialized (dev devpts, type devpts), uses transition SIDs SELinux: initialized (dev inotifyfs, type inotifyfs), uses genfs_contexts SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs SELinux: initialized (dev futexfs, type futexfs), uses genfs_contexts SELinux: initialized (dev anon_inodefs, type anon_inodefs), uses genfs_contexts SELinux: initialized (dev pipefs, type pipefs), uses task SIDs SELinux: initialized (dev sockfs, type sockfs), uses task SIDs SELinux: initialized (dev cpuset, type cpuset), uses genfs_contexts SELinux: initialized (dev proc, type proc), uses genfs_contexts SELinux: initialized (dev bdev, type bdev), uses genfs_contexts SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts audit(1190046134.968:3): policy loaded auid=4294967295 sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray Uniform CD-ROM driver Revision: 3.20 sr 4:0:0:0: Attached scsi CD-ROM sr0 sd 0:0:0:0: Attached scsi generic sg0 type 0 sr 4:0:0:0: Attached scsi generic sg1 type 5 input: Power Button (FF) as /class/input/input4 ACPI: Power Button (FF) [PWRF] input: Sleep Button (CM) as /class/input/input5 ACPI: Sleep Button (CM) [SLPB] input: Lid Switch as /class/input/input6 ACPI: Lid Switch [LID] input: Power Button (CM) as /class/input/input7 ACPI: Power Button (CM) [PWRB] ACPI: AC Adapter [ACAD] (on-line) set_level status: 0 input: Video Bus as /class/input/input8 ACPI: Video Device [UVGA] (multi-head: yes rom: no post: no) ACPI: Battery Slot [BAT0] (battery present) forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.60. ACPI: PCI Interrupt Link [LK4E] enabled at IRQ 19 ACPI: PCI Interrupt 0000:03:00.0[A] -> Link [LK4E] -> GSI 19 (level, low) -> IRQ 19 PCI: Setting latency timer of device 0000:03:00.0 to 64 ACPI: PCI Interrupt Link [LMAC] enabled at IRQ 20 ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LMAC] -> GSI 20 (level, low) -> IRQ 20 PCI: Setting latency timer of device 0000:00:0a.0 to 64 forcedeth: using HIGHDMA ssb: rev 60000000 WARNING: at drivers/ssb/main.c:889 ssb_tmslow_reject_bitmask() (Tainted: G M ) Call Trace: [] :ssb:ssb_tmslow_reject_bitmask+0x76/0x7f [] :ssb:ssb_device_is_enabled+0xf/0x39 [] :ssb:ssb_pcicore_init+0x19/0x4a [] :ssb:ssb_attach_queued_buses+0x83/0x25e [] :ssb:ssb_pci_get_invariants+0x0/0x2ba [] :ssb:ssb_bus_register+0x144/0x196 [] :ssb:ssb_bus_pcibus_register+0x2a/0x4b [] :ssb:ssb_pcihost_probe+0x6f/0x9e [] pci_device_probe+0xd0/0x137 [] driver_probe_device+0xff/0x17c [] __driver_attach+0x90/0xcc [] __driver_attach+0x0/0xcc [] __driver_attach+0x0/0xcc [] bus_for_each_dev+0x43/0x6e [] bus_add_driver+0x7b/0x19d [] __pci_register_driver+0x68/0x9a [] :ssb:ssb_modinit+0x45/0x5d [] sys_init_module+0x15d5/0x173a [] system_call+0x7e/0x83 ssb: Sonics Silicon Backplane found on PCI device 0000:03:00.0 rtc_cmos 00:07: rtc core: registered rtc_cmos as rtc0 rtc0: alarms up to one year, y3k Bluetooth: Core ver 2.11 NET: Registered protocol family 31 Bluetooth: HCI device and connection manager initialized Bluetooth: HCI socket layer initialized drivers/net/usb/rtl8150.c: rtl8150 based usb-ethernet driver v0.6.2 (2004/08/27) sdhci: Secure Digital Host Controller Interface driver sdhci: Copyright(c) Pierre Ossman drivers/net/usb/rtl8150.c: eth0: rtl8150 is detected usbcore: registered new interface driver rtl8150 Bluetooth: HCI USB driver ver 2.9 usbcore: registered new interface driver hci_usb net eth4: device_rename: sysfs_create_symlink failed (-17) eth0: forcedeth.c: subsystem: 0103c:30cf bound to 0000:00:0a.0 ACPI: PCI Interrupt Link [LNK1] enabled at IRQ 5 ACPI: PCI Interrupt 0000:02:05.0[A] -> Link [LNK1] -> GSI 5 (level, low) -> IRQ 5 firewire_ohci: Added fw-ohci device 0000:02:05.0, OHCI version 1.10 sdhci: SDHCI controller found at 0000:02:05.1 [1180:0822] (rev 22) ACPI: PCI Interrupt Link [LNK2] enabled at IRQ 7 ACPI: PCI Interrupt 0000:02:05.1[B] -> Link [LNK2] -> GSI 7 (level, low) -> IRQ 7 mmc0: SDHCI at 0xf6100800 irq 7 DMA ACPI: PCI Interrupt Link [LAZA] enabled at IRQ 21 ACPI: PCI Interrupt 0000:00:07.0[A] -> Link [LAZA] -> GSI 21 (level, low) -> IRQ 21 PCI: Setting latency timer of device 0000:00:07.0 to 64 Floppy drive(s): fd0 is 1.44M firewire_core: created new fw device fw0 (0 config rom retries, S400) SELinux: initialized (dev ramfs, type ramfs), uses genfs_contexts NET: Registered protocol family 10 lo: Disabled Privacy Extensions ACPI: PCI Interrupt Link [LGPU] enabled at IRQ 16 ACPI: PCI Interrupt 0000:00:12.0[A] -> Link [LGPU] -> GSI 16 (level, low) -> IRQ 16 floppy0: no floppy controllers found device-mapper: multipath: version 1.0.5 loaded loop: module loaded EXT3 FS on dm-0, internal journal kjournald starting. Commit interval 5 seconds EXT3 FS on sda3, internal journal EXT3-fs: mounted filesystem with ordered data mode. SELinux: initialized (dev sda3, type ext3), uses xattr SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs Adding 2031608k swap on /dev/mapper/VolGroup00-LogVol01. Priority:-1 extents:1 across:2031608k SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses genfs_contexts drivers/net/usb/rtl8150.c: eth4: allmulti set drivers/net/usb/rtl8150.c: eth4: allmulti set drivers/net/usb/rtl8150.c: eth4: allmulti set drivers/net/usb/rtl8150.c: eth4: allmulti set drivers/net/usb/rtl8150.c: eth4: allmulti set eth0: no IPv6 routers present audit(1190046219.989:4): audit_pid=2265 old=0 by auid=4294967295 subj=system_u:system_r:auditd_t:s0 SELinux: initialized (dev rpc_pipefs, type rpc_pipefs), uses genfs_contexts Bluetooth: L2CAP ver 2.8 Bluetooth: L2CAP socket layer initialized Bluetooth: RFCOMM socket layer initialized Bluetooth: RFCOMM TTY layer initialized Bluetooth: RFCOMM ver 1.8 SELinux: initialized (dev autofs, type autofs), uses genfs_contexts SELinux: initialized (dev autofs, type autofs), uses genfs_contexts SELinux: initialized (dev autofs, type autofs), uses genfs_contexts set_level status: 0 set_level status: 0 set_level status: 0 set_level status: 0 set_level status: 0 set_level status: 0 set_level status: 0 set_level status: 0 set_level status: 0 set_level status: 0 set_level status: 0 set_level status: 0 set_level status: 0 set_level status: 0 set_level status: 0 set_level status: 0 set_level status: 0 set_level status: 0 set_level status: 0 set_level status: 0 set_level status: 0 set_level status: 0 set_level status: 0 set_level status: 0 eth0: link down. drivers/net/usb/rtl8150.c: eth4: allmulti set drivers/net/usb/rtl8150.c: eth4: allmulti set drivers/net/usb/rtl8150.c: eth4: allmulti set drivers/net/usb/rtl8150.c: eth4: allmulti set drivers/net/usb/rtl8150.c: eth4: allmulti set drivers/net/usb/rtl8150.c: eth4: allmulti set drivers/net/usb/rtl8150.c: eth4: allmulti set drivers/net/usb/rtl8150.c: eth4: allmulti set drivers/net/usb/rtl8150.c: eth4: allmulti set drivers/net/usb/rtl8150.c: eth4: allmulti set drivers/net/usb/rtl8150.c: eth4: allmulti set eth4: no IPv6 routers present