[K12OSN] Networking configuration
Huck
dhuckaby at paasda.org
Fri Jun 20 22:53:07 UTC 2008
regular cable
Jeremy Schubert wrote:
> Do I need a cross over cable between eth1 and my cable modem or just a
> regular cable?
>
> ----- Original Message -----
> From: John Lucas <mrjohnlucas at gmail.com>
> Date: Monday, June 16, 2008 5:44 pm
> Subject: Re: [K12OSN] Networking configuration
> To: "Support list for open source software in schools." <k12osn at redhat.com>
>
> > Jeremy Schubert wrote:
> > > I used to have three clients connected to by dlink device that
> > acts as a
> > > switch, dhcp server and proxy server (shares the internet, but
> > I guess
> > > not exactly a proxy server, anyway...) Client computers
> > gateway is set
> > > to the ip of the dlink device. The dlink device is
> > connected to the
> > > cable modem.
> > >
> > >
> > >
> > > Now I have introduced my CentOS ltsp server. Currently I
> > have eth0 and
> > > eth1 plugged into the dlink device.
> > >
> > >
> > >
> > > So, do I have to plug eth0 into my cable modem and eth1 into
> > my switch?
> > > And then the gateway for my client computers would be the ltsp
> > server
> > > instead of the dlink device?
> > >
> >
> > You shouldn't have both NICs on the same network segment
> > (subnet), it
> > will not work.
> >
> > As I recall the client side of LTSP is on eth0 by default, so
> > eth1 would
> > go on the cable modem and eth0 goes on the LAN side (not WAN
> > side) of
> > the Dlink. Your clients also go on the LAN side of the DLink.
> > This
> > assumes you want to use the LTSP server as your router/firewall
> > instead
> > of the DLink. If this is the case, then be sure to *turn off*
> > DHCP on
> > the DLink and let the LTSP server handle that task too. The WAN
> > side of
> > the DLink will not be used. The client's default route would
> > point to
> > the LTSP server (be sure to turn on packet forwarding if you
> > have PCs
> > that need to pass traffic through the server).
> >
> > The other way to do this is to run a single NIC LTSP server
> > (only eth0)
> > and plug the LTSP server and all clients onto the DLink LAN
> > side, turn
> > off DHCP on the DLink but continue to use the DLink as your
> > router/firewall with the WAN side connected to the cable modem.
> > In this
> > scenario, the DLink would be the default route for all clients
> > (including the LTSP server).
> >
> > > Also, during the ltsp install, the eth0 was designated
> > x.x.x.254 and
> > > eth1 dhcp. Currently I connect to the server using putty
> > (ssh). Is
> > > there a cmd line I can use to change the eth1 to static and
> > modify both
> > > cards address?
> > >
> >
> > You can usually change the network configuration with a GUI too.
> > I use
> > KDE and installed the KDE admin tools, which adds an
> > "Administration"
> > item to the main menu. The exact setup depends on your ISP. The
> > single
> > NIC setup wouldn't require changing eth1, because there would be
> > no eth1.
> >
> >
> > --
> > "History
> > doesn't repeat itself; at best it rhymes."
> > - Mark Twain
> >
> > | John
> > Lucas MrJohnLucas at gmail.com |
> > | St. Thomas, VI 00802
> > http://mrjohnlucas.googlepages.com/ |
> > | 18.3°N,
> > 65°W AST (UTC-4) |
> >
> > _______________________________________________
> > K12OSN mailing list
> > K12OSN at redhat.com
> > https://www.redhat.com/mailman/listinfo/k12osn
> > For more info see <http://www.k12os.org>
> >
>
>
> ------------------------------------------------------------------------
>
> _______________________________________________
> K12OSN mailing list
> K12OSN at redhat.com
> https://www.redhat.com/mailman/listinfo/k12osn
> For more info see <http://www.k12os.org>
More information about the K12OSN
mailing list