Do I need a cross over cable between eth1 and my cable modem or just a regular cable?<br><br>----- Original Message -----<br>From: John Lucas <mrjohnlucas@gmail.com><br>Date: Monday, June 16, 2008 5:44 pm<br>Subject: Re: [K12OSN] Networking configuration<br>To: "Support list for open source software in schools." <k12osn@redhat.com><br><br>> Jeremy Schubert wrote:<br>> > I used to have three clients connected to by dlink device that <br>> acts as a <br>> > switch, dhcp server and proxy server (shares the internet, but <br>> I guess <br>> > not exactly a proxy server, anyway...)  Client computers <br>> gateway is set <br>> > to the ip of the dlink device.   The dlink device is <br>> connected to the <br>> > cable modem.<br>> > <br>> >  <br>> > <br>> > Now I have introduced my CentOS ltsp server.  Currently I <br>> have eth0 and <br>> > eth1 plugged into the dlink device.<br>> > <br>> >  <br>> > <br>> > So, do I have to plug eth0 into my cable modem and eth1 into <br>> my switch?  <br>> > And then the gateway for my client computers would be the ltsp <br>> server <br>> > instead of the dlink device? <br>> > <br>> <br>> You shouldn't have both NICs on the same network segment <br>> (subnet), it <br>> will not work.<br>> <br>> As I recall the client side of LTSP is on eth0 by default, so <br>> eth1 would <br>> go on the cable modem and eth0 goes on the LAN side (not WAN <br>> side) of <br>> the Dlink. Your clients also go on the LAN side of the DLink. <br>> This <br>> assumes you want to use the LTSP server as your router/firewall <br>> instead <br>> of the DLink. If this is the case, then be sure to *turn off* <br>> DHCP on <br>> the DLink and let the LTSP server handle that task too. The WAN <br>> side of <br>> the DLink will not be used. The client's default route would <br>> point to <br>> the LTSP server (be sure to turn on packet forwarding if you <br>> have PCs <br>> that need to pass traffic through the server).<br>> <br>> The other way to do this is to run a single NIC LTSP server <br>> (only eth0) <br>> and plug the LTSP server and all clients onto the DLink LAN <br>> side, turn <br>> off DHCP on the DLink but continue to use the DLink as your <br>> router/firewall with the WAN side connected to the cable modem. <br>> In this <br>> scenario, the DLink would be the default route for all clients <br>> (including the LTSP server).<br>> <br>> > Also, during the ltsp install, the eth0 was designated <br>> x.x.x.254 and <br>> > eth1 dhcp.  Currently I connect to the server using putty <br>> (ssh).  Is <br>> > there a cmd line I can use to change the eth1 to static and <br>> modify both <br>> > cards address?<br>> > <br>> <br>> You can usually change the network configuration with a GUI too. <br>> I use <br>> KDE and installed the KDE admin tools, which adds an <br>> "Administration" <br>> item to the main menu. The exact setup depends on your ISP. The <br>> single <br>> NIC setup wouldn't require changing eth1, because there would be <br>> no eth1.<br>> <br>> <br>> -- <br>>          "History <br>> doesn't repeat itself; at best it rhymes."<br>>                          - Mark Twain<br>> <br>> | John <br>> Lucas                MrJohnLucas@gmail.com               |<br>> | St. Thomas, VI 00802      <br>> http://mrjohnlucas.googlepages.com/ |<br>> | 18.3°N, <br>> 65°W              AST (UTC-4)                         |<br>> <br>> _______________________________________________<br>> K12OSN mailing list<br>> K12OSN@redhat.com<br>> https://www.redhat.com/mailman/listinfo/k12osn<br>> For more info see <http://www.k12os.org><br>>