<div>I thought that as well before I submitted to the mailing list. Tried various eth settings including the standard troubleshooting ones that are out there but it did not work.</div>
<div> </div>
<div>I'm goin to do some traffic sniffing to see what's going on.</div>
<div> </div>
<div><br><br> </div>
<div class="gmail_quote">On Wed, Apr 30, 2008 at 7:07 PM, Shabazian, Chip <<a href="mailto:Chip.Shabazian@bankofamerica.com">Chip.Shabazian@bankofamerica.com</a>> wrote:<br>
<blockquote class="gmail_quote" style="PADDING-LEFT: 1ex; MARGIN: 0px 0px 0px 0.8ex; BORDER-LEFT: #ccc 1px solid">
<div>
<div dir="ltr" align="left"><span><font face="Arial" color="#0000ff" size="2">You may be running into the timeout issue when connected to Cisco (and probably other) switches.</font></span></div>
<div dir="ltr" align="left"><span><font face="Arial" color="#0000ff" size="2"></font></span> </div>
<div dir="ltr" align="left"><span><font face="Arial" color="#0000ff" size="2">use the ethtool option to set speed/duplex/auto-neg and use a delay if needed. You can find all these options in my presentation last year at Linuxworld</font></span></div>
<div dir="ltr" align="left"><span><font face="Arial" color="#0000ff" size="2"></font></span> </div>
<div dir="ltr" align="left"><span><font face="Arial" color="#0000ff" size="2"><a href="http://www.shabazian.com/lw2007.pdf" target="_blank">http://www.shabazian.com/lw2007.pdf</a></font></span></div>
<div> </div><font face="Arial" size="2"></font><br>
<div lang="en-us" dir="ltr" align="left">
<hr>
<font face="Tahoma" size="2"><b>From:</b> <a href="mailto:kickstart-list-bounces@redhat.com" target="_blank">kickstart-list-bounces@redhat.com</a> [mailto:<a href="mailto:kickstart-list-bounces@redhat.com" target="_blank">kickstart-list-bounces@redhat.com</a>] <b>On Behalf Of </b>Brent Clements<br>
<b>Sent:</b> Wednesday, April 30, 2008 4:27 PM<br><b>To:</b> <a href="mailto:kickstart-list@redhat.com" target="_blank">kickstart-list@redhat.com</a><br><b>Subject:</b> RHEL 3 kickstart network retrieval issue<br></font><br>
</div>
<div>
<div></div>
<div class="Wj3C7c">
<div></div>
<div>I am having the wierdest issue with RHEL 3 network installs. </div>
<div> </div>
<div>When I boot with a RHEL 3 boot media, I use the following boot commandline:</div>
<div> </div>
<div>linux ks=<a href="http://myhost/RHEL3.ks" target="_blank">http://myhost/RHEL3.ks</a> ksdevice=eth0 ip=<MYIP> netmask=<MYNETMASK> gateway=<MYGATEWAY> dns=<MYDNS></div>
<div> </div>
<div>Anaconda boots up but it fails at installing. I switch over to a terminal and it shows that anaconda has failed to retrieve the kickstart file from the network and also I see a no route to host error. Does not look like the network device is being set up correctly based upon the boot commandline parameters.</div>
<div> </div>
<div> </div>
<div>To Troubleshoot to make sure it wasn't the kickstart file that was the problem, I stuck this same kickstart file as an embedded kickstart on the cd and it worked fine. So that doesn't get me anywhere and validates that my actual kickstart file doesn't have errors and can install an OS </div>
<div> </div>
<div>So, I try doing the same thing but with RHEL 4 media and a RHEL4 based kickstart using the boot commandline</div>
<div> </div>
<div>
<div>linux ks=<a href="http://myhost/RHEL4.ks" target="_blank">http://myhost/RHEL4.ks</a> ksdevice=eth0 ip=<MYIP> netmask=<MYNETMASK> gateway=<MYGATEWAY> dns=<MYDNS></div>
<div> </div>
<div>Everything works fine using RHEL 4 and the command line stated right above.</div>
<div> </div>
<div> </div>
<div>Are their known issues with setting network parameters at the command line with RHEL 3? </div></div></div></div></div><br>_______________________________________________<br>Kickstart-list mailing list<br><a href="mailto:Kickstart-list@redhat.com">Kickstart-list@redhat.com</a><br>
<a href="https://www.redhat.com/mailman/listinfo/kickstart-list" target="_blank">https://www.redhat.com/mailman/listinfo/kickstart-list</a><br></blockquote></div><br>