<br><br><div class="gmail_quote">2009/8/13 Hakan VELIOGLU <span dir="ltr"><<a href="mailto:veliogluh@itu.edu.tr">veliogluh@itu.edu.tr</a>></span><br><blockquote class="gmail_quote" style="border-left: 1px solid rgb(204, 204, 204); margin: 0pt 0pt 0pt 0.8ex; padding-left: 1ex;">
----- <a href="mailto:raju.rajsand@gmail.com" target="_blank">raju.rajsand@gmail.com</a> den ileti ---------<br>
  Tarih: Thu, 13 Aug 2009 08:57:15 +0530<br>
 Kimden:  Rajagopal Swaminathan <<a href="mailto:raju.rajsand@gmail.com" target="_blank">raju.rajsand@gmail.com</a>><div class="im"><br>
Yanıt Adresi:linux clustering <<a href="mailto:linux-cluster@redhat.com" target="_blank">linux-cluster@redhat.com</a>><br>
   Konu: Re: [Linux-cluster] Is there any backup heartbeat channel<br>
   Kime: linux clustering <<a href="mailto:linux-cluster@redhat.com" target="_blank">linux-cluster@redhat.com</a>><br>
<br>
<br>
</div><div class="im"><blockquote class="gmail_quote" style="border-left: 1px solid rgb(204, 204, 204); margin: 0pt 0pt 0pt 0.8ex; padding-left: 1ex;">
Greetings,<br>
<br>
2009/8/12 Hakan VELIOGLU <<a href="mailto:veliogluh@itu.edu.tr" target="_blank">veliogluh@itu.edu.tr</a>>:<br>
<blockquote class="gmail_quote" style="border-left: 1px solid rgb(204, 204, 204); margin: 0pt 0pt 0pt 0.8ex; padding-left: 1ex;">
Hi list,<br>
<br>
I am trying a two node cluster with RH 5.3 on Sun X4150 hardware. I use a<br>
</blockquote>
<br>
IIRC, Sun x4150 has four ethernet ports. Two can be used for outside<br>
networking and two can be bonded and used for heartbeat.<br>
</blockquote></div>
I think, I couldn't explain my networking. I use two ethernet ports for xen vm which are trunk and bonded ports. Then there left two. Our network topology (which is out of my control) available for one port for server control (SSH).</blockquote>
<div>So you can't use a bonded port for both server management  and cluster communications, can you? You can configure an active-passive bonding and then you can have many virtual interfaces on top of that, i.e: bond0:0, bond0:1 and assign them the ip addesses you need.<br>
<br><br></div><blockquote class="gmail_quote" style="border-left: 1px solid rgb(204, 204, 204); margin: 0pt 0pt 0pt 0.8ex; padding-left: 1ex;"> I use the other one with a cross over cable for heartbeat. So there is no way for bonding these two interfaces. Of course if I buy an extra switch I may do this.</blockquote>
<div>You can connect them to the same switch (though you lost kind of redundancy), or you can use two crossover cables and move the management IP to the same ports you are using for the vm's.<br><br>Greetings,<br>Juanra<br>
</div><blockquote class="gmail_quote" style="border-left: 1px solid rgb(204, 204, 204); margin: 0pt 0pt 0pt 0.8ex; padding-left: 1ex;"><br>
I don't realy understand why there is no backup heartbeat channel. LVS and MS cluster has this ability.<div class="im"><br>
<blockquote class="gmail_quote" style="border-left: 1px solid rgb(204, 204, 204); margin: 0pt 0pt 0pt 0.8ex; padding-left: 1ex;">
<br>
ALOM can be used for fencing and can be on a seperate subnet if required.<br>
</blockquote></div>
I used this for fencing_ipmilan.<div class="im"><br>
<blockquote class="gmail_quote" style="border-left: 1px solid rgb(204, 204, 204); margin: 0pt 0pt 0pt 0.8ex; padding-left: 1ex;">
<br>
Regards<br>
<br>
Rajagopal<br>
<br>
--<br>
Linux-cluster mailing list<br>
<a href="mailto:Linux-cluster@redhat.com" target="_blank">Linux-cluster@redhat.com</a><br>
<a href="https://www.redhat.com/mailman/listinfo/linux-cluster" target="_blank">https://www.redhat.com/mailman/listinfo/linux-cluster</a><br>
<br>
</blockquote>
<br>
<br></div>
----- <a href="mailto:raju.rajsand@gmail.com" target="_blank">raju.rajsand@gmail.com</a> den iletiyi bitir -----<div><div></div><div class="h5"><br>
<br>
<br>
<br>
--<br>
Linux-cluster mailing list<br>
<a href="mailto:Linux-cluster@redhat.com" target="_blank">Linux-cluster@redhat.com</a><br>
<a href="https://www.redhat.com/mailman/listinfo/linux-cluster" target="_blank">https://www.redhat.com/mailman/listinfo/linux-cluster</a><br>
</div></div></blockquote></div><br>