<DIV>
<TABLE cellSpacing=0 cellPadding=0 width="100%" border=0 ?>
<TBODY>
<TR>
<TD>
<DIV> </DIV>
<DIV>HI...</DIV>
<DIV> </DIV>
<DIV>This is my first posting so not sure if posting in correct place or not. Please advise if not. </DIV>
<DIV> </DIV>
<DIV>I want to use HP DAT 24X6 SCSI tape drive with Linux 8.0. I've attached the tape drive with linux but getting following error. </DIV>
<DIV> </DIV>
<DIV>can someone please educate how the scsi tape drive installation works in linux ?</DIV>
<DIV> </DIV>
<DIV>can someone please classified below output with his/her suggestion/comments ?</DIV>
<DIV> </DIV>
<DIV>Thanks in advance for your help. I'd follow up if i need to provide any more information. </DIV>
<DIV> </DIV>
<DIV>thanks again. please help.</DIV>
<DIV> </DIV>
<DIV> </DIV>
<DIV>[BDC root]# mt -f /dev/st0 status<BR>SCSI 2 tape drive:<BR>File number=-1, block number=-1, partition=0.<BR>Tape block size 0 bytes. Density code 0x0 (default).<BR>Soft error count since last status=0<BR>General status bits on (50000):<BR>DR_OPEN IM_REP_EN<BR></DIV>
<DIV> </DIV>
<DIV>[BDC root]# more /proc/scsi/scsi<BR>Attached devices:<BR>Host: scsi0 Channel: 00 Id: 03 Lun: 00<BR>  Vendor: HP       Model: C1557A           Rev: U812<BR>  Type:   Sequential-Access                ANSI SCSI<BR>revision: 02<BR>Host: scsi0 Channel: 00 Id: 03 Lun: 01<BR>  Vendor: HP       Model: C1557A           Rev: U812<BR>  Type:   Medium Changer                   ANSI SCSI<BR>revision: 02<BR></DIV>
<DIV>[BDC root]# uname -r<BR>2.4.18-14<BR><BR><BR>[BDC root]# tar cvf /dev/st0 /etc<BR>tar: Removing leading `/' from member names<BR>etc/<BR>etc/sysconfig/<BR>etc/sysconfig/network-scripts/<BR>etc/sysconfig/network-scripts/ifup-aliases<BR>tar: /dev/st0: Wrote only 0 of 10240 bytes<BR>tar: Error is not recoverable: exiting now<BR></DIV>
<DIV> </DIV>
<DIV>[BDC root]# mt -f /dev/nst0 status<BR>SCSI 2 tape drive:<BR>File number=-1, block number=-1, partition=0.<BR>Tape block size 0 bytes. Density code 0x0 (default).<BR>Soft error count since last status=0<BR>General status bits on (50000):<BR>DR_OPEN IM_REP_EN<BR></DIV>
<DIV> </DIV>
<DIV>[BDC root]# mt -f /dev/nst1 status<BR>/dev/nst1: No such device or address<BR></DIV>
<DIV> </DIV>
<DIV>[BDC root]# mt -f /dev/nst0 status<BR>SCSI 2 tape drive:<BR>File number=-1, block number=-1, partition=0.<BR>Tape block size 0 bytes. Density code 0x0 (default).<BR>Soft error count since last status=0<BR>General status bits on (50000):<BR>DR_OPEN IM_REP_EN<BR></DIV>
<DIV>****</DIV>
<DIV>File number=-1, block number=-1 <<<<<<< those are negative -1 </DIV></TD></TR></TBODY></TABLE></DIV><p><hr size=1><font face=arial size=-1>Do you Yahoo!?<br>
<a href="http://taxes.yahoo.com/filing.html"><b>Yahoo! Finance Tax Center</a></b> - File online. File on time.