tekram dc-390u3w problem

[Damien Dye]

Hi all

I ended up getting a teckram dc-390u3w card but an having a few problems
installation into the LX164 machine was fine and srm dectects it as 
abootable card :-)

now I have moved my scsi bus from my old Adaptec 2940A and the new card 
is complaing
 that there is a parity error, while it worked fine on my old controller.

the device is a ATAbaby stand alone raid unit made by nexsan 
(www.nexsan.com) and is a Wide Ultra2 SCSI device
however the card unable to access the device, it has the factory 
ultra320 terminator on the end of the bus.
the bus works correctly with the same terminator & cabling on my ultra  
SE adaptec unit  the bus has simply been moved
from the connector on the old card to the connector on the new card.

any help would be appreciated

I have attached my kernel log below.

--
Damien Dye


 sym0: <1010-66> rev 0x1 on pci bus 0 device 6 function 0 irq 16
 sym0: using 64 bit DMA addressing
 sym0: Symbios NVRAM, ID 7, Fast-80, LVD, parity checking
 sym0: open drain IRQ line driver, using on-chip SRAM
 sym0: using LOAD/STORE-based firmware.
 sym0: handling phase mismatch from SCRIPTS.
 sym0: SCSI BUS has been reset.
 sym1: <1010-66> rev 0x1 on pci bus 0 device 6 function 1 irq 16
 sym1: using 64 bit DMA addressing
 sym1: Symbios NVRAM, ID 7, Fast-80, SE, parity checking
 sym1: open drain IRQ line driver, using on-chip SRAM
 sym1: using LOAD/STORE-based firmware.
 sym1: handling phase mismatch from SCRIPTS.
 sym1: SCSI BUS has been reset.
 scsi1 : sym-2.1.17a
 scsi2 : sym-2.1.17a
 blk: queue fffffc000edd7108, no I/O memory limit
 Vendor: PHILIPS   Model: DVAD              Rev: 6q23
 Type:   Direct-Access                      ANSI SCSI revision: 03
 blk: queue fffffc000edd6f08, no I/O memory limit
sym0:0:0: tagged command queuing enabled, command queue depth 16.
 Attached scsi disk sda at scsi1, channel 0, id 0, lun 0
 sym0:0: FAST-40 WIDE SCSI 80.0 MB/s ST (25.0 ns, offset 12)
 sym0: SCSI parity error detected: SCR1=3 DBC=11000000 SBCL=ae
 sym0: SCSI parity error detected: SCR1=1 DBC=1100000e SBCL=ae
 sda : READ CAPACITY failed.
 sda : status = 1, message = 00, host = 7, driver = 00
 sda : sense not available.
 sda : block size assumed to be 512 bytes, disk size 1GB.  
 /dev/scsi/host1/bus0/target0/lun0:sym0: SCSI parity error detected: 
SCR1=3 DBC=11001fe8 SBCL=ae
 sym0: SCSI parity error detected: SCR1=3 DBC=11001fe8 SBCL=ae
SCSI disk error : host 1 channel 0 id 0 lun 0 return code = 70002
 I/O error: dev 08:00, sector 0
 sym0: SCSI parity error detected: SCR1=3 DBC=11001be8 SBCL=ae
SCSI disk error : host 1 channel 0 id 0 lun 0 return code = 70002
 I/O error: dev 08:00, sector 2