anyone with knowledge of the artic transport, chime in

[Linux for blind general discussion]

I was not giving commands, I was making reference to serial port 
parameters.
use minicom and try
9600 for speed, 8 data bits, and 1 stop bits and no parity.
see if you get feedback with that.
kp



On Tue, 9 May 2017, Linux for blind general discussion wrote:

> Mp heree.
> when I type xon/xoff or the other command you mentioned, vinux reports commands not valid.
> I did just get minicom installed, though.
>
>
> Mark Peveto
> Registered Linux user number 600552
> Everything happens after coffee!
>
> On Tue, 9 May 2017, Linux for blind general discussion wrote:
>
>> you should probably set 9600 for speed, 8,n,1 8 bits, 1 stop bit, no parity.
>> you may have to try xon/xoff or rts/cts for handshaking.
>> I think it should be rts/cts, however.
>> Then you can load up minicom, set the same parameters with it, and you should
>> be able to output text which the synth will read.
>> When you can do that, you should be able to load speakup with it.
>> kp
>>
>>
>>
>> On Tue, 9 May 2017, Linux for blind general discussion wrote:
>>
>>> Mp here,
>>> Yeah, you're right. I've been through the setup, but have no idea what to
>>> set to what.  I tried guessing at a few settings, but no luck.
>>>
>>>
>>>
>>> Mark Peveto
>>> Registered Linux user number 600552
>>> Everything happens after coffee!
>>>
>>> On Tue, 9 May 2017, Linux for blind general discussion wrote:
>>>
>>>> This is Kelly.
>>>> I seem to recall the transport had a config mode to setup the serial port
>>>> correctly...
>>>> I think there is a little button on it to do that.
>>>> I cannot remember the steps, however.
>>>> kp
>>>>
>>>>
>>>>
>>>> On Tue, 9 May 2017, Linux for blind general discussion wrote:
>>>>
>>>>> There is someone I know who might have an idea.  will share this post
>>>>> and
>>>>> see if they can help you.
>>>>> Karen
>>>>>
>>>>>
>>>>> On Tue, 9 May 2017, Linux for blind general discussion wrote:
>>>>>
>>>>>>  I got the serial cord this afternoon.  I've connected it to the
>>>>>> transport,
>>>>>>  yet it still reports serial port notready.  Not sure how to precede
>>>>>> from
>>>>>>  here, as I'm not able to find documentation.
>>>>>>
>>>>>>
>>>>>>  Mark Peveto
>>>>>>  Registered Linux user number 600552
>>>>>>  Everything happens after coffee!
>>>>>>
>>>>>>  _______________________________________________
>>>>>>  Blinux-list mailing list
>>>>>>  Blinux-list at redhat.com
>>>>>>  https://www.redhat.com/mailman/listinfo/blinux-list
>>>>>>
>>>>>>
>>>>>
>>>>> _______________________________________________
>>>>> Blinux-list mailing list
>>>>> Blinux-list at redhat.com
>>>>> https://www.redhat.com/mailman/listinfo/blinux-list
>>>>>
>>>>>
>>>>
>>>> _______________________________________________
>>>> Blinux-list mailing list
>>>> Blinux-list at redhat.com
>>>> https://www.redhat.com/mailman/listinfo/blinux-list
>>>>
>>>
>>> _______________________________________________
>>> Blinux-list mailing list
>>> Blinux-list at redhat.com
>>> https://www.redhat.com/mailman/listinfo/blinux-list
>>>
>>
>> _______________________________________________
>> Blinux-list mailing list
>> Blinux-list at redhat.com
>> https://www.redhat.com/mailman/listinfo/blinux-list
>>
>
> _______________________________________________
> Blinux-list mailing list
> Blinux-list at redhat.com
> https://www.redhat.com/mailman/listinfo/blinux-list
>