[dm-devel] [PATCH] multipath: add option '-i' to ignore wwids file

[Christophe Varoqui]

Applied.
Thanks.


On Fri, Jul 4, 2014 at 8:20 AM, Hannes Reinecke <hare at suse.de> wrote:

> When called from udev the multipath program is used to check
> if a device should be handled by multipath. Any new device,
> however, will not be present in /etc/multipath/wwids, and
> the check will always fail.
> This patch implements the option '-i' to multipath to skip
> checking the wwids file for these scenarios.
>
> Signed-off-by: Hannes Reinecke <hare at suse.de>
> ---
>  libmultipath/config.h |  1 +
>  multipath/main.c      | 18 +++++++++++-------
>  multipath/multipath.8 |  5 ++++-
>  3 files changed, 16 insertions(+), 8 deletions(-)
>
> diff --git a/libmultipath/config.h b/libmultipath/config.h
> index ac7c58e..ca17f39 100644
> --- a/libmultipath/config.h
> +++ b/libmultipath/config.h
> @@ -106,6 +106,7 @@ struct config {
>         int max_fds;
>         int force_reload;
>         int queue_without_daemon;
> +       int ignore_wwids;
>         int checker_timeout;
>         int daemon;
>  #ifdef USE_SYSTEMD
> diff --git a/multipath/main.c b/multipath/main.c
> index 157475e..fd6262f 100644
> --- a/multipath/main.c
> +++ b/multipath/main.c
> @@ -84,7 +84,7 @@ usage (char * progname)
>  {
>         fprintf (stderr, VERSION_STRING);
>         fprintf (stderr, "Usage:\n");
> -       fprintf (stderr, "  %s [-a|-c|-w|-W] [-d] [-r] [-v lvl] [-p pol]
> [-b fil] [-q] [dev]\n", progname);
> +       fprintf (stderr, "  %s [-a|-c|-w|-W] [-d] [-r] [-i] [-v lvl] [-p
> pol] [-b fil] [-q] [dev]\n", progname);
>         fprintf (stderr, "  %s -l|-ll|-f [-v lvl] [-b fil] [dev]\n",
> progname);
>         fprintf (stderr, "  %s -F [-v lvl]\n", progname);
>         fprintf (stderr, "  %s -t\n", progname);
> @@ -103,6 +103,7 @@ usage (char * progname)
>                 "  -d      dry run, do not create or update devmaps\n" \
>                 "  -t      dump internal hardware table\n" \
>                 "  -r      force devmap reload\n" \
> +               "  -i      ignore wwids file\n" \
>                 "  -B      treat the bindings file as read only\n" \
>                 "  -p      policy
> failover|multibus|group_by_serial|group_by_prio\n" \
>                 "  -b fil  bindings file location\n" \
> @@ -307,12 +308,12 @@ configure (void)
>                 }
>                 condlog(3, "scope limited to %s", refwwid);
>                 if (conf->cmd == CMD_VALID_PATH) {
> -                       if (check_wwids_file(refwwid, 0) == 0){
> -                               printf("%s is a valid multipath device
> path\n", conf->dev);
> +                       if (conf->ignore_wwids ||
> +                           check_wwids_file(refwwid, 0) == 0)
>                                 r = 0;
> -                       }
> -                       else
> -                               printf("%s is not a valid multipath device
> path\n", conf->dev);
> +
> +                       printf("%s %s a valid multipath device path\n",
> +                              conf->dev, r == 0 ? "is" : "is not");
>                         goto out;
>                 }
>         }
> @@ -445,7 +446,7 @@ main (int argc, char *argv[])
>         if (load_config(DEFAULT_CONFIGFILE, udev))
>                 exit(1);
>
> -       while ((arg = getopt(argc, argv, ":adchl::FfM:v:p:b:BrtqwW")) !=
> EOF ) {
> +       while ((arg = getopt(argc, argv, ":adchl::FfM:v:p:b:BritqwW")) !=
> EOF ) {
>                 switch(arg) {
>                 case 1: printf("optarg : %s\n",optarg);
>                         break;
> @@ -503,6 +504,9 @@ main (int argc, char *argv[])
>                 case 'r':
>                         conf->force_reload = 1;
>                         break;
> +               case 'i':
> +                       conf->ignore_wwids = 1;
> +                       break;
>                 case 't':
>                         r = dump_config();
>                         goto out_free_config;
> diff --git a/multipath/multipath.8 b/multipath/multipath.8
> index b6479b1..13e2e89 100644
> --- a/multipath/multipath.8
> +++ b/multipath/multipath.8
> @@ -8,7 +8,7 @@ multipath \- Device mapper target autoconfig
>  .RB [\| \-b\ \c
>  .IR bindings_file \|]
>  .RB [\| \-d \|]
> -.RB [\| \-h | \-l | \-ll | \-f | \-t | \-F | \-B | \-c | \-q | \|-r | \-a
> | \-w | \-W \|]
> +.RB [\| \-h | \-l | \-ll | \-f | \-t | \-F | \-B | \-c | \-q | \|-r |
> \|-i | \-a | \-w | \-W \|]
>  .RB [\| \-p\ \c
>  .BR failover | multibus | group_by_serial | group_by_prio |
> group_by_node_name \|]
>  .RB [\| device \|]
> @@ -55,6 +55,9 @@ print internal hardware table to stdout
>  .B \-r
>  force devmap reload
>  .TP
> +.B \-i
> +ignore wwids file when processing devices
> +.TP
>  .B \-B
>  treat the bindings file as read only
>  .TP
> --
> 1.8.4.5
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://listman.redhat.com/archives/dm-devel/attachments/20140724/5ed310dd/attachment.htm>