Jul 13 11:24:10 jimbo kernel: QLogic Fibre Channel HBA Driver
Jul 13 11:24:10 jimbo kernel: ACPI: PCI Interrupt 0000:02:01.0[A] -> GSI 28 (level, low) -> IRQ 28
Jul 13 11:24:10 jimbo kernel: qla2xxx 0000:02:01.0: Found an ISP2422, irq 28, iobase 0xffffc20001428000
Jul 13 11:24:10 jimbo kernel: qla2xxx 0000:02:01.0: Configuring PCI space...
Jul 13 11:24:10 jimbo kernel: qla2xxx 0000:02:01.0: Configure NVRAM parameters...
Jul 13 11:24:10 jimbo kernel: qla2xxx 0000:02:01.0: Verifying loaded RISC code...
Jul 13 11:24:10 jimbo kernel: scsi(5): **** Load RISC code ****
Jul 13 11:24:10 jimbo kernel: scsi(5): Verifying Checksum of loaded RISC code.
Jul 13 11:24:10 jimbo kernel: scsi(5): Checksum OK, start firmware.
Jul 13 11:24:10 jimbo kernel: qla2xxx 0000:02:01.0: Allocated (64 KB) for EFT...
Jul 13 11:24:10 jimbo kernel: qla2xxx 0000:02:01.0: Allocated (1413 KB) for firmware dump...
Jul 13 11:24:10 jimbo kernel: scsi(5): Issue init firmware.
Jul 13 11:24:10 jimbo kernel: DEBUG: detect hba 5 at address = ffff81007dd84530
Jul 13 11:24:10 jimbo kernel: scsi5 : qla2xxx
Jul 13 11:24:12 jimbo kernel: scsi(5): qla2x00_loop_resync()
Jul 13 11:24:15 jimbo kernel: qla2xxx 0000:02:01.0: 
Jul 13 11:24:15 jimbo kernel: QLogic Fibre Channel HBA Driver: 8.01.07-k7-debug
Jul 13 11:24:15 jimbo kernel: QLogic QLA2462 - Sun PCI-X 2.0 to 4Gb FC, Dual Channel
Jul 13 11:24:15 jimbo kernel: ISP2422: PCI-X Mode 1 (100 MHz) @ 0000:02:01.0 hdma+, host#=5, fw=4.00.27 [IP] 
Jul 13 11:24:15 jimbo kernel: ACPI: PCI Interrupt 0000:02:01.1[B] -> GSI 29 (level, low) -> IRQ 29
Jul 13 11:24:15 jimbo kernel: qla2xxx 0000:02:01.1: Found an ISP2422, irq 29, iobase 0xffffc2000142a000
Jul 13 11:24:15 jimbo kernel: qla2xxx 0000:02:01.1: Configuring PCI space...
Jul 13 11:24:15 jimbo kernel: qla2xxx 0000:02:01.1: Configure NVRAM parameters...
Jul 13 11:24:15 jimbo kernel: qla2xxx 0000:02:01.1: Verifying loaded RISC code...
Jul 13 11:24:15 jimbo kernel: scsi(6): **** Load RISC code ****
Jul 13 11:24:15 jimbo kernel: scsi(6): Verifying Checksum of loaded RISC code.
Jul 13 11:24:15 jimbo kernel: scsi(6): Checksum OK, start firmware.
Jul 13 11:24:15 jimbo kernel: qla2xxx 0000:02:01.1: Allocated (64 KB) for EFT...
Jul 13 11:24:15 jimbo kernel: qla2xxx 0000:02:01.1: Allocated (1413 KB) for firmware dump...
Jul 13 11:24:15 jimbo kernel: scsi(6): Issue init firmware.
Jul 13 11:24:15 jimbo kernel: DEBUG: detect hba 6 at address = ffff81007de68530
Jul 13 11:24:15 jimbo kernel: scsi6 : qla2xxx
Jul 13 11:24:16 jimbo kernel: scsi(6): Asynchronous LIP RESET (f700).
Jul 13 11:24:16 jimbo kernel: qla2xxx 0000:02:01.1: LIP reset occured (f700).
Jul 13 11:24:16 jimbo kernel: scsi(6): LIP occured (f700).
Jul 13 11:24:16 jimbo kernel: qla2xxx 0000:02:01.1: LIP occured (f700).
Jul 13 11:24:16 jimbo kernel: scsi(6): Asynchronous LIP RESET (f7f7).
Jul 13 11:24:16 jimbo kernel: qla2xxx 0000:02:01.1: LIP reset occured (f7f7).
Jul 13 11:24:16 jimbo kernel: scsi(6): Asynchronous P2P MODE received.
Jul 13 11:24:17 jimbo kernel: scsi(6): Asynchronous LOOP UP (4 Gbps).
Jul 13 11:24:17 jimbo kernel: qla2xxx 0000:02:01.1: LOOP UP detected (4 Gbps).
Jul 13 11:24:17 jimbo kernel: scsi(6): Asynchronous PORT UPDATE.
Jul 13 11:24:17 jimbo kernel: scsi(6): Port database changed ffff 0006 0000.
Jul 13 11:24:17 jimbo kernel: scsi(6): qla2x00_reset_marker()
Jul 13 11:24:17 jimbo kernel: scsi(6): qla2x00_loop_resync()
Jul 13 11:24:17 jimbo kernel: scsi(6): F/W Ready - OK 
Jul 13 11:24:17 jimbo kernel: scsi(6): fw_state=3 curr time=100032111.
Jul 13 11:24:17 jimbo kernel: scsi(6): Configure loop -- dpc flags =0x40800e0
Jul 13 11:24:17 jimbo kernel: scsi(6): RSCN queue entry[0] = [00/000000].
Jul 13 11:24:17 jimbo kernel: scsi(6): device_resync: rscn overflow.
Jul 13 11:24:17 jimbo kernel: scsi(6): RFT_ID exiting normally.
Jul 13 11:24:17 jimbo kernel: scsi(6): RFF_ID exiting normally.
Jul 13 11:24:17 jimbo kernel: scsi(6): RNN_ID exiting normally.
Jul 13 11:24:17 jimbo kernel: scsi(6): RSNN_NN exiting normally.
Jul 13 11:24:17 jimbo kernel: scsi(6): GID_PT entry - nn 200600a0b8119910 pn 202700a0b8119910 portid=050100.
Jul 13 11:24:17 jimbo kernel: scsi(6): GID_PT entry - nn 200100e08bb191cd pn 210100e08bb191cd portid=050200.
Jul 13 11:24:17 jimbo kernel: scsi(6): GPSC failed, rejected request:
Jul 13 11:24:17 jimbo kernel: 0   1   2   3   4   5   6   7   8   9  Ah  Bh  Ch  Dh  Eh  Fh
Jul 13 11:24:17 jimbo kernel: --------------------------------------------------------------
Jul 13 11:24:17 jimbo kernel: 01  00  00  00  fa  01  00  00  80  01  00  00  00  0b  00  00
Jul 13 11:24:17 jimbo kernel: scsi(6): GPSC failed, rejected request:
Jul 13 11:24:17 jimbo kernel: 0   1   2   3   4   5   6   7   8   9  Ah  Bh  Ch  Dh  Eh  Fh
Jul 13 11:24:17 jimbo kernel: --------------------------------------------------------------
Jul 13 11:24:17 jimbo kernel: 01  00  00  00  fa  01  00  00  80  01  00  00  00  0b  00  00
Jul 13 11:24:17 jimbo kernel: scsi(6): device wrap (050200)
Jul 13 11:24:17 jimbo kernel: scsi(6): Trying Fabric Login w/loop id 0x0081 for port 050100.
Jul 13 11:24:17 jimbo kernel: scsi(6): 202700a0b8119910 -- unsupported FM port operating speed (0000).
Jul 13 11:24:17 jimbo kernel: scsi(6): LOOP READY
Jul 13 11:24:17 jimbo kernel: scsi(6): qla2x00_loop_resync - end
Jul 13 11:24:17 jimbo kernel: qla2xxx 0000:02:01.1: scsi(6:0:0:0): Queue depth adjusted-up to 4.
Jul 13 11:24:17 jimbo kernel: scsi 6:0:0:0: Direct-Access     IBM      1815      FAStT  0914 PQ: 0 ANSI: 3
Jul 13 11:24:17 jimbo kernel: qla2xxx 0000:02:01.1: 
Jul 13 11:24:17 jimbo kernel: QLogic Fibre Channel HBA Driver: 8.01.07-k7-debug
Jul 13 11:24:17 jimbo kernel: QLogic QLA2462 - Sun PCI-X 2.0 to 4Gb FC, Dual Channel
Jul 13 11:24:17 jimbo kernel: ISP2422: PCI-X Mode 1 (100 MHz) @ 0000:02:01.1 hdma+, host#=6, fw=4.00.27 [IP] 
Jul 13 11:24:17 jimbo kernel: sd 6:0:0:0: [sdc] 6291456 512-byte hardware sectors (3221 MB)
Jul 13 11:24:17 jimbo kernel: sd 6:0:0:0: [sdc] Write Protect is off
Jul 13 11:24:17 jimbo kernel: sd 6:0:0:0: [sdc] Mode Sense: 77 00 10 08
Jul 13 11:24:17 jimbo kernel: sd 6:0:0:0: [sdc] Write cache: enabled, read cache: enabled, supports DPO and FUA
Jul 13 11:24:17 jimbo kernel: sd 6:0:0:0: [sdc] 6291456 512-byte hardware sectors (3221 MB)
Jul 13 11:24:17 jimbo kernel: sd 6:0:0:0: [sdc] Write Protect is off
Jul 13 11:24:17 jimbo kernel: sd 6:0:0:0: [sdc] Mode Sense: 77 00 10 08
Jul 13 11:24:17 jimbo kernel: sd 6:0:0:0: [sdc] Write cache: enabled, read cache: enabled, supports DPO and FUA
Jul 13 11:24:17 jimbo kernel: sdc:scsi(6): Asynchronous PORT UPDATE ignored 0000/0004/0600.
Jul 13 11:24:17 jimbo kernel: scsi(6): Asynchronous PORT UPDATE ignored 0000/0007/0b00.
Jul 13 11:24:17 jimbo kernel: end_request: I/O error, dev sdc, sector 0
Jul 13 11:24:17 jimbo kernel: Buffer I/O error on device sdc, logical block 0
Jul 13 11:24:18 jimbo kernel: end_request: I/O error, dev sdc, sector 0
Jul 13 11:24:18 jimbo kernel: Buffer I/O error on device sdc, logical block 0
Jul 13 11:24:18 jimbo kernel: unable to read partition table
Jul 13 11:24:18 jimbo kernel: sd 6:0:0:0: [sdc] Attached SCSI disk
Jul 13 11:24:18 jimbo kernel: scsi 6:0:0:31: Direct-Access     IBM      Universal Xport  0914 PQ: 0 ANSI: 3
Jul 13 11:24:18 jimbo kernel: end_request: I/O error, dev sdc, sector 6291328
Jul 13 11:24:18 jimbo kernel: Buffer I/O error on device sdc, logical block 786416
Jul 13 11:24:19 jimbo kernel: end_request: I/O error, dev sdc, sector 6291328
Jul 13 11:24:19 jimbo kernel: Buffer I/O error on device sdc, logical block 786416
Jul 13 11:24:19 jimbo kernel: end_request: I/O error, dev sdc, sector 6291448
Jul 13 11:24:19 jimbo kernel: Buffer I/O error on device sdc, logical block 786431
Jul 13 11:24:20 jimbo kernel: end_request: I/O error, dev sdc, sector 6291448
Jul 13 11:24:20 jimbo kernel: Buffer I/O error on device sdc, logical block 786431
Jul 13 11:24:20 jimbo kernel: end_request: I/O error, dev sdc, sector 6291448
Jul 13 11:24:20 jimbo kernel: Buffer I/O error on device sdc, logical block 786431
Jul 13 11:24:21 jimbo kernel: end_request: I/O error, dev sdc, sector 6291448
Jul 13 11:24:21 jimbo kernel: Buffer I/O error on device sdc, logical block 786431
Jul 13 11:24:21 jimbo kernel: end_request: I/O error, dev sdc, sector 6291448
Jul 13 11:24:21 jimbo kernel: Buffer I/O error on device sdc, logical block 786431
Jul 13 11:24:22 jimbo kernel: end_request: I/O error, dev sdc, sector 6291448
Jul 13 11:24:22 jimbo kernel: Buffer I/O error on device sdc, logical block 786431
Jul 13 11:24:22 jimbo kernel: end_request: I/O error, dev sdc, sector 6291392
Jul 13 11:24:22 jimbo kernel: Buffer I/O error on device sdc, logical block 786424
Jul 13 11:24:23 jimbo kernel: end_request: I/O error, dev sdc, sector 6291440
Jul 13 11:24:23 jimbo kernel: end_request: I/O error, dev sdc, sector 6291448
Jul 13 11:24:24 jimbo kernel: end_request: I/O error, dev sdc, sector 6291448
Jul 13 11:24:24 jimbo kernel: end_request: I/O error, dev sdc, sector 0
Jul 13 11:24:25 jimbo kernel: end_request: I/O error, dev sdc, sector 0
Jul 13 11:24:26 jimbo kernel: end_request: I/O error, dev sdc, sector 0
Jul 13 11:24:26 jimbo kernel: end_request: I/O error, dev sdc, sector 0
Jul 13 11:24:27 jimbo kernel: end_request: I/O error, dev sdc, sector 0
Jul 13 11:24:27 jimbo kernel: end_request: I/O error, dev sdc, sector 0
Jul 13 11:24:27 jimbo kernel: printk: 8 messages suppressed.
Jul 13 11:24:27 jimbo kernel: Buffer I/O error on device sdc, logical block 0
Jul 13 11:24:28 jimbo kernel: end_request: I/O error, dev sdc, sector 0
Jul 13 11:24:28 jimbo kernel: end_request: I/O error, dev sdc, sector 0
Jul 13 11:24:29 jimbo kernel: end_request: I/O error, dev sdc, sector 0
Jul 13 11:24:29 jimbo kernel: end_request: I/O error, dev sdc, sector 0
Jul 13 11:24:30 jimbo kernel: end_request: I/O error, dev sdc, sector 0
Jul 13 11:24:30 jimbo kernel: end_request: I/O error, dev sdc, sector 0
Jul 13 11:24:31 jimbo kernel: end_request: I/O error, dev sdc, sector 0
Jul 13 11:24:31 jimbo kernel: end_request: I/O error, dev sdc, sector 0
Jul 13 11:24:32 jimbo kernel: end_request: I/O error, dev sdc, sector 0
Jul 13 11:24:32 jimbo kernel: qla2xxx 0000:02:01.0: Cable is unplugged...
Jul 13 11:24:32 jimbo kernel: scsi(5): fw_state=4 curr time=100033044.
Jul 13 11:24:32 jimbo kernel: scsi(5): Firmware ready **** FAILED ****.
Jul 13 11:24:32 jimbo kernel: qla2x00_loop_resync(): **** FAILED ****
Jul 13 11:24:32 jimbo kernel: scsi(5): qla2x00_loop_resync - end
Jul 13 11:24:32 jimbo kernel: end_request: I/O error, dev sdc, sector 0
Jul 13 11:24:32 jimbo kernel: printk: 9 messages suppressed.
Jul 13 11:24:32 jimbo kernel: Buffer I/O error on device sdc, logical block 0
Jul 13 11:24:33 jimbo kernel: end_request: I/O error, dev sdc, sector 0
Jul 13 11:24:34 jimbo kernel: end_request: I/O error, dev sdc, sector 0
Jul 13 11:24:34 jimbo kernel: end_request: I/O error, dev sdc, sector 0
Jul 13 11:24:35 jimbo kernel: end_request: I/O error, dev sdc, sector 0
Jul 13 11:24:35 jimbo kernel: end_request: I/O error, dev sdc, sector 0
Jul 13 11:24:36 jimbo kernel: end_request: I/O error, dev sdc, sector 0
Jul 13 11:24:36 jimbo kernel: end_request: I/O error, dev sdc, sector 0
Jul 13 11:24:37 jimbo kernel: end_request: I/O error, dev sdc, sector 0
Jul 13 11:24:37 jimbo kernel: end_request: I/O error, dev sdc, sector 0
Jul 13 11:24:37 jimbo kernel: printk: 8 messages suppressed.
Jul 13 11:24:37 jimbo kernel: Buffer I/O error on device sdc, logical block 0
Jul 13 11:24:38 jimbo kernel: end_request: I/O error, dev sdc, sector 0
Jul 13 11:24:38 jimbo kernel: end_request: I/O error, dev sdc, sector 0
Jul 13 11:24:39 jimbo kernel: end_request: I/O error, dev sdc, sector 0
Jul 13 11:24:39 jimbo kernel: device-mapper: multipath rdac: using RDAC command with timeout 15000
Jul 13 11:24:39 jimbo kernel: device-mapper: multipath rdac: queueing MODE_SELECT command on 8:32
Jul 13 11:24:41 jimbo kernel: qla2xxx 0000:02:01.1: ISP System Error - mbx1=0h mbx2=8012h mbx3=8002h.
Jul 13 11:24:41 jimbo kernel: qla2xxx 0000:02:01.1: Firmware dump saved to temp buffer (6/ffffc2000191f000).
Jul 13 11:24:41 jimbo kernel: scsi(5): Loop Down - aborting the queues before time expire
Jul 13 11:24:41 jimbo kernel: scsi(6): dpc: sched qla2x00_abort_isp ha = ffff81007de68530
Jul 13 11:24:41 jimbo kernel: qla2xxx 0000:02:01.1: Performing ISP error recovery - ha= ffff81007de68530.
Jul 13 11:24:41 jimbo kernel: device-mapper: multipath: Failing path 8:32.
Jul 13 11:24:41 jimbo kernel: scsi(6): **** Load RISC code ****
Jul 13 11:24:41 jimbo kernel: scsi(6): Verifying Checksum of loaded RISC code.
Jul 13 11:24:41 jimbo kernel: scsi(6): Checksum OK, start firmware.
Jul 13 11:24:41 jimbo kernel: scsi(6): Issue init firmware.
Jul 13 11:24:42 jimbo kernel: scsi(6): Asynchronous LIP RESET (f700).
Jul 13 11:24:42 jimbo kernel: qla2xxx 0000:02:01.1: LIP reset occured (f700).
Jul 13 11:24:42 jimbo kernel: scsi(6): LIP occured (f700).
Jul 13 11:24:42 jimbo kernel: qla2xxx 0000:02:01.1: LIP occured (f700).
Jul 13 11:24:42 jimbo kernel: scsi(6): Asynchronous LIP RESET (f7f7).
Jul 13 11:24:42 jimbo kernel: qla2xxx 0000:02:01.1: LIP reset occured (f7f7).
Jul 13 11:24:42 jimbo kernel: scsi(6): Asynchronous P2P MODE received.
Jul 13 11:24:42 jimbo kernel: scsi(6): fcport-0 - port retry count: 0 remaining
Jul 13 11:24:43 jimbo kernel: scsi(6): Asynchronous LOOP UP (4 Gbps).
Jul 13 11:24:43 jimbo kernel: qla2xxx 0000:02:01.1: LOOP UP detected (4 Gbps).
Jul 13 11:24:43 jimbo kernel: scsi(6): Asynchronous PORT UPDATE.
Jul 13 11:24:43 jimbo kernel: scsi(6): Port database changed ffff 0006 0000.
Jul 13 11:24:43 jimbo kernel: scsi(6): Asynchronous PORT UPDATE ignored 0000/0004/0600.
Jul 13 11:24:43 jimbo kernel: scsi(6): Asynchronous PORT UPDATE ignored 0000/0007/0b00.
Jul 13 11:24:43 jimbo kernel: scsi(6): F/W Ready - OK 
Jul 13 11:24:43 jimbo kernel: scsi(6): fw_state=3 curr time=100033b09.
Jul 13 11:24:43 jimbo kernel: qla2x00_restart_isp(): Start configure loop, status = 0
Jul 13 11:24:43 jimbo kernel: scsi(6): Configure loop -- dpc flags =0x4080049
Jul 13 11:24:43 jimbo kernel: scsi(6): RSCN queue entry[0] = [00/000000].
Jul 13 11:24:43 jimbo kernel: scsi(6): device_resync: rscn overflow.
Jul 13 11:24:43 jimbo kernel: scsi(6): RFT_ID exiting normally.
Jul 13 11:24:43 jimbo kernel: scsi(6): RFF_ID exiting normally.
Jul 13 11:24:43 jimbo kernel: scsi(6): RNN_ID exiting normally.
Jul 13 11:24:43 jimbo kernel: scsi(6): RSNN_NN exiting normally.
Jul 13 11:24:43 jimbo kernel: scsi(6): GID_PT entry - nn 200600a0b8119910 pn 202700a0b8119910 portid=050100.
Jul 13 11:24:43 jimbo kernel: scsi(6): GID_PT entry - nn 200100e08bb191cd pn 210100e08bb191cd portid=050200.
Jul 13 11:24:43 jimbo kernel: scsi(6): GPSC failed, rejected request:
Jul 13 11:24:43 jimbo kernel: 0   1   2   3   4   5   6   7   8   9  Ah  Bh  Ch  Dh  Eh  Fh
Jul 13 11:24:43 jimbo kernel: --------------------------------------------------------------
Jul 13 11:24:43 jimbo kernel: 01  00  00  00  fa  01  00  00  80  01  00  00  00  0b  00  00
Jul 13 11:24:43 jimbo kernel: scsi(6): GPSC failed, rejected request:
Jul 13 11:24:43 jimbo kernel: 0   1   2   3   4   5   6   7   8   9  Ah  Bh  Ch  Dh  Eh  Fh
Jul 13 11:24:43 jimbo kernel: --------------------------------------------------------------
Jul 13 11:24:43 jimbo kernel: 01  00  00  00  fa  01  00  00  80  01  00  00  00  0b  00  00
Jul 13 11:24:43 jimbo kernel: qla24xx_fabric_logout(6): failed to complete IOCB -- completion status (31)  ioparam=a/0.
Jul 13 11:24:43 jimbo kernel: scsi(6): device wrap (050200)
Jul 13 11:24:43 jimbo kernel: scsi(6): Trying Fabric Login w/loop id 0x0081 for port 050100.
Jul 13 11:24:44 jimbo kernel: scsi(6): 202700a0b8119910 -- unsupported FM port operating speed (0000).
Jul 13 11:24:44 jimbo kernel: scsi(6): LOOP READY
Jul 13 11:24:44 jimbo kernel: qla2x00_restart_isp(): Configure loop done, status = 0x0
Jul 13 11:24:44 jimbo kernel: qla2x00_abort_isp(6): exiting.
Jul 13 11:24:44 jimbo kernel: scsi(6): dpc: qla2x00_abort_isp end