[edk2-devel] [PATCH edk2-platforms v2 2/3] NetsecDxe: put phy in loopback mode to guarantee stable RXCLK input

[Masahisa Kojima]

NETSEC hardware requires stable RXCLK input upon initialization
triggered with DISCORE = 0.
However, RXCLK input could be unstable depending on phy chipset
and deployed network environment, which could cause NETSEC to
hang up during initialization.

We solve this platform/environment dependent issue by temporarily
putting phy in loopback mode, then we can expect the stable RXCLK input.

Signed-off-by: Masahisa Kojima <masahisa.kojima at linaro.org>
Signed-off-by: Satoru Okamoto <okamoto.satoru at socionext.com>
---
 Silicon/Socionext/SynQuacer/Drivers/Net/NetsecDxe/netsec_for_uefi/netsec_sdk/src/ogma_misc.c | 72 ++++++++++++++++++++
 Silicon/Socionext/SynQuacer/Drivers/Net/NetsecDxe/netsec_for_uefi/netsec_sdk/src/ogma_reg.h  |  4 ++
 2 files changed, 76 insertions(+)

diff --git a/Silicon/Socionext/SynQuacer/Drivers/Net/NetsecDxe/netsec_for_uefi/netsec_sdk/src/ogma_misc.c b/Silicon/Socionext/SynQuacer/Drivers/Net/NetsecDxe/netsec_for_uefi/netsec_sdk/src/ogma_misc.c
index 7481d2da2d24..5f6ddc0c745e 100644
--- a/Silicon/Socionext/SynQuacer/Drivers/Net/NetsecDxe/netsec_for_uefi/netsec_sdk/src/ogma_misc.c
+++ b/Silicon/Socionext/SynQuacer/Drivers/Net/NetsecDxe/netsec_for_uefi/netsec_sdk/src/ogma_misc.c
@@ -327,6 +327,60 @@ STATIC ogma_uint32 ogma_calc_pkt_ctrl_reg_param (
     return param;
 }
 
+STATIC
+void
+ogma_pre_init_microengine (
+  ogma_handle_t ogma_handle
+  )
+{
+  UINT16 Data;
+
+  /* Remove dormant settings */
+  Data = ogma_get_phy_reg (ogma_handle, OGMA_PHY_REG_ADDR_CONTROL) &
+         ~((1U << OGMA_PHY_CONTROL_REG_POWER_DOWN) |
+         (1U << OGMA_PHY_CONTROL_REG_ISOLATE));
+
+  ogma_set_phy_reg (ogma_handle, OGMA_PHY_REG_ADDR_CONTROL, Data);
+
+  while ((ogma_get_phy_reg (ogma_handle, OGMA_PHY_REG_ADDR_CONTROL) &
+          ((1U << OGMA_PHY_CONTROL_REG_POWER_DOWN) |
+           (1U << OGMA_PHY_CONTROL_REG_ISOLATE))) != 0);
+
+  /* Put phy in loopback mode to guarantee RXCLK input */
+  Data |= (1U << OGMA_PHY_CONTROL_REG_LOOPBACK);
+
+  ogma_set_phy_reg (ogma_handle, OGMA_PHY_REG_ADDR_CONTROL, Data);
+
+  while ((ogma_get_phy_reg (ogma_handle, OGMA_PHY_REG_ADDR_CONTROL) &
+          (1U << OGMA_PHY_CONTROL_REG_LOOPBACK)) == 0);
+}
+
+STATIC
+void
+ogma_post_init_microengine (
+  IN ogma_handle_t ogma_handle
+  )
+{
+  UINT16 Data;
+
+  /* Get phy back to normal operation */
+  Data = ogma_get_phy_reg (ogma_handle, OGMA_PHY_REG_ADDR_CONTROL) &
+         ~(1U << OGMA_PHY_CONTROL_REG_LOOPBACK);
+
+  ogma_set_phy_reg (ogma_handle, OGMA_PHY_REG_ADDR_CONTROL, Data);
+
+  while ((ogma_get_phy_reg (ogma_handle, OGMA_PHY_REG_ADDR_CONTROL) &
+          (1U << OGMA_PHY_CONTROL_REG_LOOPBACK)) != 0);
+
+  Data |= (1U << OGMA_PHY_CONTROL_REG_RESET);
+
+  /* Apply software reset */
+  ogma_set_phy_reg (ogma_handle, OGMA_PHY_REG_ADDR_CONTROL, Data);
+
+  while ((ogma_get_phy_reg (ogma_handle, OGMA_PHY_REG_ADDR_CONTROL) &
+          (1U << OGMA_PHY_CONTROL_REG_RESET)) != 0);
+}
+
 ogma_err_t ogma_init (
     void *base_addr,
     pfdep_dev_handle_t dev_handle,
@@ -551,6 +605,17 @@ ogma_err_t ogma_init (
     ogma_write_reg( ctrl_p, OGMA_REG_ADDR_DMA_TMR_CTRL,
                     ( ogma_uint32)( ( OGMA_CONFIG_CLK_HZ / OGMA_CLK_MHZ) - 1) );
 
+    /*
+     * Do pre-initialization tasks for microengine
+     *
+     * In particular, we put phy in loopback mode
+     * in order to make sure RXCLK keeps provided to mac
+     * irrespective of phy link status,
+     * which is required for microengine intialization.
+     * This will be disabled once microengine initialization complete.
+     */
+    ogma_pre_init_microengine (ctrl_p);
+
     /* start microengines */
     ogma_write_reg( ctrl_p, OGMA_REG_ADDR_DIS_CORE, 0);
 
@@ -573,6 +638,13 @@ ogma_err_t ogma_init (
         goto err;
     }
 
+    /*
+     * Do post-initialization tasks for microengine
+     *
+     * We put phy in normal mode and apply reset.
+     */
+    ogma_post_init_microengine (ctrl_p);
+
     /* clear microcode load end status */
     ogma_write_reg( ctrl_p, OGMA_REG_ADDR_TOP_STATUS,
                     OGMA_TOP_IRQ_REG_ME_START);
diff --git a/Silicon/Socionext/SynQuacer/Drivers/Net/NetsecDxe/netsec_for_uefi/netsec_sdk/src/ogma_reg.h b/Silicon/Socionext/SynQuacer/Drivers/Net/NetsecDxe/netsec_for_uefi/netsec_sdk/src/ogma_reg.h
index 30c716352b37..ca769084cb31 100644
--- a/Silicon/Socionext/SynQuacer/Drivers/Net/NetsecDxe/netsec_for_uefi/netsec_sdk/src/ogma_reg.h
+++ b/Silicon/Socionext/SynQuacer/Drivers/Net/NetsecDxe/netsec_for_uefi/netsec_sdk/src/ogma_reg.h
@@ -138,8 +138,12 @@
 /* bit fields for PHY CONTROL Register */
 #define OGMA_PHY_CONTROL_REG_SPEED_SELECTION_MSB (6)
 #define OGMA_PHY_CONTROL_REG_DUPLEX_MODE         (8)
+#define OGMA_PHY_CONTROL_REG_ISOLATE             (10)
+#define OGMA_PHY_CONTROL_REG_POWER_DOWN          (11)
 #define OGMA_PHY_CONTROL_REG_AUTO_NEGO_ENABLE    (12)
 #define OGMA_PHY_CONTROL_REG_SPEED_SELECTION_LSB (13)
+#define OGMA_PHY_CONTROL_REG_LOOPBACK            (14)
+#define OGMA_PHY_CONTROL_REG_RESET               (15)
 
 /* bit fields for PHY STATUS Register */
 #define OGMA_PHY_STATUS_REG_LINK_STATUS       (2)
-- 
2.17.1


-=-=-=-=-=-=-=-=-=-=-=-
Groups.io Links: You receive all messages sent to this group.

View/Reply Online (#44351): https://edk2.groups.io/g/devel/message/44351
Mute This Topic: https://groups.io/mt/32593951/1813853
Group Owner: devel+owner at edk2.groups.io
Unsubscribe: https://edk2.groups.io/g/devel/unsub  [edk2-devel-archive at redhat.com]
-=-=-=-=-=-=-=-=-=-=-=-