[edk2-devel] [edk2-platforms: PATCH 03/14] Marvell/Library: ArmadaBoardDescLib: Add PCIE information

[Ard Biesheuvel]

On Thu, 9 May 2019 at 11:53, Marcin Wojtas <mw at semihalf.com> wrote:
>
> Introduce new callback that can provide information
> about PCIE controller per-board description.
> A new structure is defined containing base addresses,
> windows/bus configuration and reset GPIO usage indication.
>
> Contributed-under: TianoCore Contribution Agreement 1.1
> Signed-off-by: Marcin Wojtas <mw at semihalf.com>
> ---
>  Silicon/Marvell/Include/Library/ArmadaBoardDescLib.h | 46 ++++++++++++++++++++
>  1 file changed, 46 insertions(+)
>
> diff --git a/Silicon/Marvell/Include/Library/ArmadaBoardDescLib.h b/Silicon/Marvell/Include/Library/ArmadaBoardDescLib.h
> index 6ec5ace..530a2ba 100644
> --- a/Silicon/Marvell/Include/Library/ArmadaBoardDescLib.h
> +++ b/Silicon/Marvell/Include/Library/ArmadaBoardDescLib.h
> @@ -15,6 +15,7 @@
>  #define __ARMADA_BOARD_DESC_LIB_H__
>
>  #include <Library/ArmadaSoCDescLib.h>
> +#include <Library/MvGpioLib.h>
>
>  //
>  // COMPHY controllers per-board description
> @@ -111,6 +112,51 @@ typedef struct {
>  } MV_BOARD_XHCI_DESC;
>
>  //
> +// PCIE controllers description
> +//
> +typedef struct {
> +  EFI_PHYSICAL_ADDRESS PcieBaseAddress;
> +  EFI_PHYSICAL_ADDRESS ConfigSpaceAddress;

In EDK2, the PCIe base address is usually the ECAM base address, not
the address of the DBI interface (which is not standardized by PCIe).
So you can either avoid 'base' entirely, and use Dbi and Ecam/Config,
or you can use 'base' for the latter, but not for the former.

> +  BOOLEAN HaveResetGpio;
> +  MV_GPIO_PIN PcieResetGpio;
> +  UINT64 PcieBusMin;
> +  UINT64 PcieBusMax;
> +  UINT64 PcieIoTranslation;
> +  UINT64 PcieIoWinBase;
> +  UINT64 PcieIoWinSize;
> +  UINT64 PcieMmio32Translation;
> +  UINT64 PcieMmio32WinBase;
> +  UINT64 PcieMmio32WinSize;
> +  UINT64 PcieMmio64Translation;
> +  UINT64 PcieMmio64WinBase;
> +  UINT64 PcieMmio64WinSize;
> +} MV_PCIE_CONTROLLER;
> +
> +typedef struct {
> +  MV_PCIE_CONTROLLER *PcieControllers;
> +  UINTN               PcieControllerCount;
> +} MV_BOARD_PCIE_DESCRIPTION;
> +
> +/**
> +  Return the number and description of PCIE controllers used on the platform.
> +
> +  @param[in out] **PcieControllers      Array containing PCIE controllers'
> +                                        description.
> +  @param[in out]  *PcieControllerCount  Amount of used PCIE controllers.
> +
> +  @retval EFI_SUCCESS                   The data were obtained successfully.
> +  @retval EFI_NOT_FOUND                 None of the controllers is used.
> +  @retval other                         Return error status.
> +
> +**/
> +EFI_STATUS
> +EFIAPI
> +ArmadaBoardPcieControllerGet (
> +  IN OUT MV_PCIE_CONTROLLER **PcieControllers,

Make this MV_PCIE_CONTROLLER CONST** if you can.

> +  IN OUT UINTN               *PcieControllerCount
> +  );
> +
> +//
>  // PP2 NIC devices per-board description
>  //
>  typedef struct {
> --
> 2.7.4
>

-=-=-=-=-=-=-=-=-=-=-=-
Groups.io Links: You receive all messages sent to this group.

View/Reply Online (#40795): https://edk2.groups.io/g/devel/message/40795
Mute This Topic: https://groups.io/mt/31553476/1813853
Group Owner: devel+owner at edk2.groups.io
Unsubscribe: https://edk2.groups.io/g/devel/unsub  [edk2-devel-archive at redhat.com]
-=-=-=-=-=-=-=-=-=-=-=-