From frank-buettner at gmx.net Wed Nov 1 12:47:43 2006 From: frank-buettner at gmx.net (=?ISO-8859-15?Q?Frank_B=FCttner?=) Date: Wed, 01 Nov 2006 13:47:43 +0100 Subject: Postfix und maildir Message-ID: <4548976F.9030402@gmx.net> Hallo hat jemand eine Idee, wie ich Postfix dazu ?berreden die E-Mails im maildir Format nicht unter /home/$user/Maildir sondern unter /var/spool/mail/%user abzulegen? Danke -------------- next part -------------- A non-text attachment was scrubbed... Name: smime.p7s Type: application/x-pkcs7-signature Size: 4285 bytes Desc: S/MIME Cryptographic Signature URL: From mcbeee at gmail.com Sat Nov 4 12:01:08 2006 From: mcbeee at gmail.com (Marc Bratmann) Date: Sat, 4 Nov 2006 13:01:08 +0100 Subject: Problem mit wpa_supplicant und madwifi Message-ID: Hallo, ich habe Probleme mit der Installation meiner WLAN-Verbindung. Die Ausgangssituation: Hard- und Software Netgear WG311T (Atheros Chipset) Speedport W700V (Router) 2.6.18-1.2200.fc5 (Fedora Core 5) wireless-tools (Version 28) madwifi (Version 0.9.2) wpa_supplicant (Version 0.4.9) Routerkonfiguration SSID: KeepOut Channel: Automatic Mode: 802.11g + 802.11b (Mixed Mode) Encryption: WPA2 with Pre-shared key DHCP: enabled Netzwerkstatus [root at localhost marc]# ifconfig -a ath0 Link encap:Ethernet Hardware Adresse 00:14:6C:8C:9F:22 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:23 errors:0 dropped:0 overruns:0 frame:0 TX packets:42 errors:19 dropped:19 overruns:0 carrier:0 Kollisionen:0 Sendewarteschlangenl?nge:0 RX bytes:3105 (3.0 KiB) TX bytes:5395 (5.2 KiB) wifi0 Link encap:UNSPEC Hardware Adresse 00-14-6C-8C-9F-22-78-02-00-00-00-00-00-00-00-00 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:27670 errors:0 dropped:0 overruns:0 frame:25609 TX packets:2399 errors:3 dropped:0 overruns:0 carrier:0 Kollisionen:0 Sendewarteschlangenl?nge:199 RX bytes:3582554 (3.4 MiB) TX bytes:126853 (123.8 KiB) Interrupt:11 Speicher:e0960000-e0970000 [root at localhost marc]# iwconfig wifi0 no wireless extensions. Warning: Driver for device ath0 has been compiled with version 20 of Wireless Extension, while this program supports up to version 19. Some things may be broken... ath0 IEEE 802.11g ESSID:"KeepOut" Nickname:"localhost.localdomain" Mode:Managed Frequency:2.412 GHz Access Point: Not-Associated Bit Rate:0 kb/s Tx-Power:18 dBm Sensitivity=0/3 Retry:off RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality=0/94 Signal level=-95 dBm Noise level=-95 dBm Rx invalid nwid:26519 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 [root at localhost marc]# iwlist ath0 scan Warning: Driver for device ath0 has been compiled with version 20 of Wireless Extension, while this program supports up to version 19. Some things may be broken... ath0 Scan completed : Cell 01 - Address: 00:12:BF:7F:5C:B9 ESSID:"KeepOut" Mode:Master Frequency:2.412 GHz (Channel 1) Quality=37/94 Signal level=-58 dBm Noise level=-95 dBm Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s 12 Mb/s; 24 Mb/s; 36 Mb/s; 9 Mb/s; 18 Mb/s 48 Mb/s; 54 Mb/s Extra:bcn_int=100 IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : CCMP Pairwise Ciphers (1) : CCMP Authentication Suites (1) : PSK Extra:wme_ie=dd180050f2020101000003a4000027a4000042435e0062322f00 Konfigurationsdateien [root at localhost marc]# cat /etc/wpa_supplicant/wpa_supplicant.conf ctrl_interface=/var/run/wpa_supplicant ctrl_interface_group=wheel eapol_version=2 ap_scan=1 fast_reauth=1 # Home WLAN network={ scan_ssid=1 proto=WPA RSN key_mgmt=WPA-PSK pairwise=CCMP TKIP group=CCMP TKIP priority=2 ssid="KeepOut" psk=[...] } [root at localhost marc]# cat /etc/sysconfig/network-scripts/ifcfg-ath0 IPV6INIT=no ONBOOT=yes USERCTL=no PEERDNS=yes TYPE=Wireless DEVICE=ath0 HWADDR=00:14:6C:8C:9F:22 BOOTPROTO=dhcp ESSID=KeepOut MODE=Managed RATE=Auto WPA=yes Problem beim Aufruf von wpa_supplicant [root at localhost marc]# wpa_supplicant -d -c/etc/wpa_supplicant/wpa_supplicant.conf -iath0 -Dmadwifi Initializing interface 'ath0' conf '/etc/wpa_supplicant/wpa_supplicant.conf' driver 'madwifi' ctrl_interface 'N/A' Configuration file '/etc/wpa_supplicant/wpa_supplicant.conf' -> '/etc/wpa_supplicant/wpa_supplicant.conf' Reading configuration file '/etc/wpa_supplicant/wpa_supplicant.conf' ctrl_interface='/var/run/wpa_supplicant' ctrl_interface_group=10 (from group name 'wheel') eapol_version=2 ap_scan=1 fast_reauth=1 Priority group 2 id=0 ssid='KeepOut' Initializing interface (2) 'ath0' EAPOL: SUPP_PAE entering state DISCONNECTED EAPOL: KEY_RX entering state NO_KEY_RECEIVE EAPOL: SUPP_BE entering state INITIALIZE EAP: EAP entering state DISABLED EAPOL: External notification - portEnabled=0 EAPOL: External notification - portValid=0 SIOCGIWRANGE: WE(compiled)=20 WE(source)=13 enc_capa=0xf capabilities: key_mgmt 0xf enc 0xf Own MAC address: 00:14:6c:8c:9f:22 wpa_driver_madwifi_del_key: keyidx=0 wpa_driver_madwifi_del_key: keyidx=1 wpa_driver_madwifi_del_key: keyidx=2 wpa_driver_madwifi_del_key: keyidx=3 wpa_driver_madwifi_set_countermeasures: enabled=0 wpa_driver_madwifi_set_drop_unencrypted: enabled=1 Setting scan request: 0 sec 100000 usec Added interface ath0 Wireless event: cmd=0x8b06 len=8 State: DISCONNECTED -> SCANNING Starting AP scan (specific SSID) Scan SSID - hexdump_ascii(len=7): 4b 65 65 70 4f 75 74 KeepOut Wireless event: cmd=0x8b1a len=16 Wireless event: cmd=0x8b19 len=8 Received 738 bytes of scan results (3 BSSes) Scan results: 3 Selecting BSS from priority group 2 0: 00:12:bf:7f:5c:b9 ssid='KeepOut' wpa_ie_len=0 rsn_ie_len=22 caps=0x11 selected based on RSN IE Trying to associate with 00:12:bf:7f:5c:b9 (SSID='KeepOut' freq=2412 MHz) Cancelling scan request WPA: clearing own WPA/RSN IE Automatic auth_alg selection: 0x1 RSN: using IEEE 802.11i/D9.0 WPA: Selected cipher suites: group 16 pairwise 16 key_mgmt 2 WPA: clearing AP WPA IE WPA: set AP RSN IE - hexdump(len=22): 30 14 01 00 00 0f ac 04 01 00 00 0f ac 04 01 00 00 0f ac 02 00 00 WPA: using GTK CCMP WPA: using PTK CCMP WPA: using KEY_MGMT WPA-PSK WPA: Set own WPA IE default - hexdump(len=22): 30 14 01 00 00 0f ac 04 01 00 00 0f ac 04 01 00 00 0f ac 02 00 00 No keys have been configured - skip key clearing wpa_driver_madwifi_set_drop_unencrypted: enabled=1 State: SCANNING -> ASSOCIATING wpa_driver_madwifi_associate ioctl[IEEE80211_IOCTL_SETMLME]: Invalid argument Association request to the driver failed Setting authentication timeout: 15 sec 0 usec EAPOL: External notification - EAP success=0 EAPOL: External notification - EAP fail=0 EAPOL: External notification - portControl=Auto RSN: Ignored PMKID candidate without preauth flag Wireless event: cmd=0x8b1a len=16 Wireless event: cmd=0x8b15 len=20 Wireless event: new AP: 00:12:bf:7f:5c:b9 State: ASSOCIATING -> ASSOCIATED Associated to a new BSS: BSSID=00:12:bf:7f:5c:b9 No keys have been configured - skip key clearing Associated with 00:12:bf:7f:5c:b9 WPA: Association event - clear replay counter EAPOL: External notification - portEnabled=0 EAPOL: External notification - portValid=0 EAPOL: External notification - EAP success=0 EAPOL: External notification - portEnabled=1 EAPOL: SUPP_PAE entering state CONNECTING EAPOL: SUPP_BE entering state IDLE Setting authentication timeout: 10 sec 0 usec RX EAPOL from 00:12:bf:7f:5c:b9 Setting authentication timeout: 10 sec 0 usec IEEE 802.1X RX: version=1 type=3 length=117 EAPOL-Key type=2 key_info 0x8a (ver=2 keyidx=0 rsvd=0 Pairwise Ack) key_length=16 key_data_length=22 replay_counter - hexdump(len=8): 00 00 00 00 00 00 00 0a key_nonce - hexdump(len=32): 54 66 68 a5 67 fa 3b ed 4f 94 61 35 11 9b fa fa c2 d3 a9 f1 7f e6 55 c0 2f f4 64 09 64 04 ba 7a key_iv - hexdump(len=16): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 key_rsc - hexdump(len=8): 00 00 00 00 00 00 00 00 key_id (reserved) - hexdump(len=8): 00 00 00 00 00 00 00 00 key_mic - hexdump(len=16): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 State: ASSOCIATED -> 4WAY_HANDSHAKE WPA: RX message 1 of 4-Way Handshake from 00:12:bf:7f:5c:b9 (ver=2) RSN: msg 1/4 key data - hexdump(len=22): dd 14 00 0f ac 04 f4 3b e6 c6 a6 54 e1 a7 1a 3c 9a 61 81 a0 68 e4 RSN: PMKID from Authenticator - hexdump(len=16): f4 3b e6 c6 a6 54 e1 a7 1a 3c 9a 61 81 a0 68 e4 RSN: no matching PMKID found WPA: WPA IE for msg 2/4 - hexdump(len=22): 30 14 01 00 00 0f ac 04 01 00 00 0f ac 04 01 00 00 0f ac 02 00 00 WPA: Renewed SNonce - hexdump(len=32): d2 4c 5f cd a5 25 9f a3 cf 54 2f 67 d6 08 5e fb 7c 51 53 a2 89 a2 fe 49 c6 68 2f 0f 68 44 1a f1 WPA: PMK - hexdump(len=32): [REMOVED] WPA: PTK - hexdump(len=64): [REMOVED] WPA: Sending EAPOL-Key 2/4 RTM_NEWLINK, IFLA_IFNAME: Interface 'ath0' added EAPOL: startWhen --> 0 EAPOL: SUPP_PAE entering state CONNECTING EAPOL: txStart WPA: drop TX EAPOL in non-IEEE 802.1X mode (type=1 len=0) RX EAPOL from 00:12:bf:7f:5c:b9 IEEE 802.1X RX: version=1 type=3 length=117 EAPOL-Key type=2 key_info 0x8a (ver=2 keyidx=0 rsvd=0 Pairwise Ack) key_length=16 key_data_length=22 replay_counter - hexdump(len=8): 00 00 00 00 00 00 00 0b key_nonce - hexdump(len=32): 54 66 68 a5 67 fa 3b ed 4f 94 61 35 11 9b fa fa c2 d3 a9 f1 7f e6 55 c0 2f f4 64 09 64 04 ba 7a key_iv - hexdump(len=16): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 key_rsc - hexdump(len=8): 00 00 00 00 00 00 00 00 key_id (reserved) - hexdump(len=8): 00 00 00 00 00 00 00 00 key_mic - hexdump(len=16): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 State: 4WAY_HANDSHAKE -> 4WAY_HANDSHAKE WPA: RX message 1 of 4-Way Handshake from 00:12:bf:7f:5c:b9 (ver=2) RSN: msg 1/4 key data - hexdump(len=22): dd 14 00 0f ac 04 f4 3b e6 c6 a6 54 e1 a7 1a 3c 9a 61 81 a0 68 e4 RSN: PMKID from Authenticator - hexdump(len=16): f4 3b e6 c6 a6 54 e1 a7 1a 3c 9a 61 81 a0 68 e4 RSN: no matching PMKID found WPA: WPA IE for msg 2/4 - hexdump(len=22): 30 14 01 00 00 0f ac 04 01 00 00 0f ac 04 01 00 00 0f ac 02 00 00 WPA: PMK - hexdump(len=32): [REMOVED] WPA: PTK - hexdump(len=64): [REMOVED] WPA: Sending EAPOL-Key 2/4 CTRL-EVENT-TERMINATING - signal 2 received Removing interface ath0 State: 4WAY_HANDSHAKE -> DISCONNECTED wpa_driver_madwifi_deauthenticate No keys have been configured - skip key clearing EAPOL: External notification - portEnabled=0 EAPOL: SUPP_PAE entering state DISCONNECTED EAPOL: SUPP_BE entering state INITIALIZE EAPOL: External notification - portValid=0 wpa_driver_madwifi_set_drop_unencrypted: enabled=0 wpa_driver_madwifi_set_countermeasures: enabled=0 No keys have been configured - skip key clearing Cancelling scan request Probleml?sung Keine Ahnung... Offensichtlich kommt die WPA2 Verbindung nicht hoch. Einige Logmeldungen deuten auf Probleme hin "Association request to the driver failed". Aber was fange ich damit nun an und wie l?se ich das Problem? Vielleicht mache ich auch ganz andere Fehler. Bin leider noch relativ unerfahren unter Linux... Vielen Dank f?r Eure Hilfe! Besten Gru?, Marc -------------- next part -------------- An HTML attachment was scrubbed... URL: From ubeck at c3pdm.com Sat Nov 4 14:34:14 2006 From: ubeck at c3pdm.com (Uwe Beck) Date: Sat, 4 Nov 2006 15:34:14 +0100 Subject: Problem mit wpa_supplicant und madwifi In-Reply-To: References: Message-ID: <200611041534.14235.ubeck@c3pdm.com> Hallo Marc, gleich vorweg, madwifi und wpa_supplicant laufen zusammen, aber es braucht etwas, bis alles in der Konfiguration stimmt. Nicht aufgeben also. On Saturday 04 November 2006 13:01, Marc Bratmann wrote: > Hallo, > > ich habe Probleme mit der Installation meiner WLAN-Verbindung. Die > Ausgangssituation: > > Hard- und Software > > Netgear WG311T (Atheros Chipset) > Speedport W700V (Router) > 2.6.18-1.2200.fc5 (Fedora Core 5) > wireless-tools (Version 28) > madwifi (Version 0.9.2) Woher kommt madwifi? Falls es ein RPM ist, Dateinamen bekannt geben, von wem ist es? > wpa_supplicant (Version 0.4.9) Bitte die Ausgabe von "rpm -q wpa_supplicant" posten. > Routerkonfiguration > > SSID: KeepOut > Channel: Automatic > Mode: 802.11g + 802.11b (Mixed Mode) > Encryption: WPA2 with Pre-shared key > DHCP: enabled Vergebe hier mal einen festen Channel z.B. 11. Bitte beachte fuer weiter unten, hier hast Du WAP2 eingestellt. > Netzwerkstatus > [root at localhost marc]# iwconfig > wifi0 no wireless extensions. > > Warning: Driver for device ath0 has been compiled with version 20 > of Wireless Extension, while this program supports up to version 19. > Some things may be broken... Kommt diese Ausgabe auch dann, wenn Du die Atheros Kernelmodule selber aus der Source uebersetzt? Laeuft die Compilierung der madwifi Version 0.9.2 unter FC5 ueberhaupt durch? Irgendwas passt ja schliesslich nicht zusammen, wie man sieht. > [root at localhost marc]# iwlist ath0 scan > Warning: Driver for device ath0 has been compiled with version 20 > of Wireless Extension, while this program supports up to version 19. > Some things may be broken... > > ath0 Scan completed : > Cell 01 - Address: 00:12:BF:7F:5C:B9 > ESSID:"KeepOut" > Mode:Master > Frequency:2.412 GHz (Channel 1) > Quality=37/94 Signal level=-58 dBm Noise level=-95 > dBm Encryption key:on > Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s > 12 Mb/s; 24 Mb/s; 36 Mb/s; 9 Mb/s; 18 Mb/s > 48 Mb/s; 54 Mb/s > Extra:bcn_int=100 > IE: IEEE 802.11i/WPA2 Version 1 > Group Cipher : CCMP > Pairwise Ciphers (1) : CCMP > Authentication Suites (1) : PSK > > Extra:wme_ie=dd180050f2020101000003a4000027a4000042435e0062322f00 > > [root at localhost marc]# cat /etc/wpa_supplicant/wpa_supplicant.conf > ctrl_interface=/var/run/wpa_supplicant > ctrl_interface_group=wheel > eapol_version=2 > ap_scan=1 > fast_reauth=1 > > # Home WLAN > network={ > scan_ssid=1 > proto=WPA RSN > key_mgmt=WPA-PSK > pairwise=CCMP TKIP > group=CCMP TKIP > > priority=2 > ssid="KeepOut" > psk=[...] > } Im WLAN-Router hast Du WPA2 eingestellt. Folglich musst Du proto=WPA RSN aendern in: proto=WPA2 Habe in wpa_supplicant.conf genau das stehen und der WLAN-Router ist ein Speedport W701V, in dem ich WPA2 aktiviert habe. > [root at localhost marc]# cat /etc/sysconfig/network-scripts/ifcfg-ath0 > IPV6INIT=no > ONBOOT=yes > USERCTL=no > PEERDNS=yes > TYPE=Wireless > DEVICE=ath0 > HWADDR=00:14:6C:8C:9F:22 > BOOTPROTO=dhcp > ESSID=KeepOut > MODE=Managed > RATE=Auto > WPA=yes WPA=yes - wuerde ich mal entfernen oder auf Kommentar setzen, kommt der von einem Konfigprogramm rein? Dafuer aufnehmen oder aendern: CHANNEL=11 MODE=Auto RATE=Auto > Problem beim Aufruf von wpa_supplicant > > [root at localhost marc]# wpa_supplicant -d > -c/etc/wpa_supplicant/wpa_supplicant.conf -iath0 -Dmadwifi > Initializing interface 'ath0' conf Alle folgenden Meldungen (habe dies absichtlich entfernt) deuten auf die proto= Einstellung hin. Kann mich auch an solche Meldungen bei meinem Umstieg von WPA auf WPA2 erinnern. Alternativ kannst Du am WLAN-Router ja mal auf WAP umstellen. Vermutlich geht es aber auch erst, wenn Du auf beiden Seiten den Channel fest vorgibst. > Probleml?sung > ... was fange ich damit nun an und wie l?se ich das Problem? Habe im Moment meine Konfigdateien nicht zur Hand. Ich kann Dir aber sagen, dass man einfach mit den Parametern etwas variieren muss, bis es passt. Habe das mit madwifi 0.9.2 und der wpa_supplicant Version, das im RPM-Namen fc6 hat unter RHEL4 am Laufen. Ist damit die selber wpa_supplicant Version, meine ich. Die madwifi Kernelmodule, die ATrpms.net fuer FC5 hat, sollten laufen ( da gab es beim Erscheinen von madwifi 0.9.2 ein Problem, dass aber in diesen RPMs geloest ist). > Vielen Dank f?r Eure Hilfe! > > Besten Gru?, > Marc Gruss Uwe ubeck(at)c3pdm.com From mcbeee at gmail.com Sun Nov 5 10:56:38 2006 From: mcbeee at gmail.com (Marc Bratmann) Date: Sun, 5 Nov 2006 11:56:38 +0100 Subject: Problem mit wpa_supplicant und madwifi In-Reply-To: <200611041534.14235.ubeck@c3pdm.com> References: <200611041534.14235.ubeck@c3pdm.com> Message-ID: Hallo Uwe (& nat?rlich auch alle anderen), vielen Dank f?r die Infos. So schnell gebe ich auch nicht auf. 2006/11/4, Uwe Beck : > Woher kommt madwifi? Falls es ein RPM ist, Dateinamen bekannt geben, von wem > ist es? Das Paket ist aus dem Livna Repository. Die Ausgabe von "rpm -q madwifi" ist: madwifi-0.9.2-1.lvn5 > Bitte die Ausgabe von "rpm -q wpa_supplicant" posten. wpa_supplicant-0.4.9-1.fc5 > > Routerkonfiguration > > Vergebe hier mal einen festen Channel z.B. 11. Erledigt. > > Warning: Driver for device ath0 has been compiled with version 20 > > of Wireless Extension, while this program supports up to version 19. > > Some things may be broken... > > Kommt diese Ausgabe auch dann, wenn Du die Atheros Kernelmodule selber aus der > Source uebersetzt? Laeuft die Compilierung der madwifi Version 0.9.2 unter > FC5 ueberhaupt durch? Irgendwas passt ja schliesslich nicht zusammen, wie man sieht. Google hat hierzu z.B. folgendes ausgespuckt "although there does not appear to be any problems other than the error messages". Ich stelle den Versuch mal etwas nach hinten. Als Linux-Neuling m?sste ich mich auch erst einmal in "Kernelmodule selber aus der Source ?bersetzen" einlesen ;-) > > [root at localhost marc]# cat /etc/wpa_supplicant/wpa_supplicant.conf > > Im WLAN-Router hast Du WPA2 eingestellt. Folglich musst Du > > proto=WPA RSN > > aendern in: > > proto=WPA2 Erledigt. Ich habe hier unterschiedliche Informationen gefunden. WPA2 schien mir nur ein Alias f?r RSN zu sein. > > [root at localhost marc]# cat /etc/sysconfig/network-scripts/ifcfg-ath0 > > WPA=yes - wuerde ich mal entfernen oder auf Kommentar setzen, kommt der von > einem Konfigprogramm rein? Erledigt. Den Parameter habe ich gesetzt (hatte ich irgendwo gelesen). > Dafuer aufnehmen oder aendern: > CHANNEL=11 > MODE=Auto > RATE=Auto Erledigt. > > Problem beim Aufruf von wpa_supplicant > > > > [root at localhost marc]# wpa_supplicant -d > > -c/etc/wpa_supplicant/wpa_supplicant.conf -iath0 -Dmadwifi Die Verbindung kommt weiterhin nicht hoch. Ich habe es auch vergeblich mit WPA und entsprechender Einstellung auf Router und in der wpa_supplicant.conf versucht (proto=WPA). Die Logs sind beide im Anhang. > [...] Und nun? Besten Gru? und Dank, Marc -------------- next part -------------- A non-text attachment was scrubbed... Name: wpa_supplicant-WPA2.log Type: text/x-log Size: 12652 bytes Desc: not available URL: -------------- next part -------------- A non-text attachment was scrubbed... Name: wpa_supplicant-WPA.log Type: text/x-log Size: 12140 bytes Desc: not available URL: From jan_schaefer at b0n541.net Tue Nov 7 07:42:39 2006 From: jan_schaefer at b0n541.net (Jan =?ISO-8859-1?Q?Sch=E4fer?=) Date: Tue, 07 Nov 2006 08:42:39 +0100 Subject: /etc/smartd.conf wird =?iso-8859-1?q?=FCberschrieben?= Message-ID: <1162885359.5083.3.camel@legolas.imise.uni-leipzig.de> Hallo, ich habe letzte Woche das Update auf Fedora Core 6 gewagt. Nach der Installation habe ich die /etc/smartd.conf so angepasst, dass meine Festplatten in der Nacht selbstst?ndig Tests zur Gesundheit durchf?hren. Komischerweise werden diese Anpassungen nach einem Neustart des Systems und/oder Smart-Daemon wieder mit den Standardwerten ?berschrieben. Wei? jemand, wie man die Einstellungen dauerhaft hinbekommt? Danke und Gru?, Jan -- PGP: 2814 0DC4 597A 1083 9AA4 6F76 0DD9 54E1 B706 0963 -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 189 bytes Desc: Dies ist ein digital signierter Nachrichtenteil URL: From gerold at lugd.org Wed Nov 8 12:00:34 2006 From: gerold at lugd.org (Gerold Kassube) Date: Wed, 08 Nov 2006 13:00:34 +0100 Subject: Invitation to the FAD Message-ID: <1162987234.3450.17.camel@Amilo-GK.homenet.local> you'll find it as PDF at http://fedoraproject.org/wiki/FAD?action=AttachFile&do=get&target=invite_FAD.pdf First FEDORA AMBASSADORS DAY (FAD EMEA) ======================================= The Fedora Ambassador Day (FAD) is where Ambassadors and other interested members of the Fedora Community come together to plan for future Fedora events and get to know each other. This is your chance to meet other Fedora community members (Ambassadors, Developers) in person. We are proud to invite you to the first FAD in EMEA. The Event will start date ==== December 1st, 2006 (6 pm GMT+1) till December 3rd, 2006 location ======== Werner Mennicke Haus R?hrberg e.V. Im Grossfeld 2 D-79639 Grenzach-Wyhlen - Germany - Agenda ====== Friday ------ afternoon: ?come together? Saturday -------- morning: Keynote from a FAMSCO Member small introduction of the participants afternoon: planning EMEA events for 2007 Breakout-sessions evening: Surprise event with local ?Linux Users? Sunday ------ if desired, visiting University of Basel with introduction in the used Red Hat Cluster Additional information * Accommodation * we have to pay per night and person EUR 5,50 / each. * We have the following rooms: -1- room with bunk bed, cupboard and washbasin -1- room with three bunk beds, cupboard and washbasin -4- rooms with each bunk bed, cupboard and washbasin -1- big room with five bunk beds and cupboards there are different showers and toilets. * You have to take care by your own for bed sheets, sleeping bag and your pillow. * Meals * Organized. Please indicate if you have special dietary requirements (vegetarian, allergies, ...) * Trip-planing * next airport Basel ? Mulhouse (international airport) * next railway-station L?rrach * best reachable railway-station Basel (Badischer Bahnhof) * by car Google Maps is your friend :) * Registration * please send your engaging registration latest November, 18th by E-Mail to GeroldKa at fedoraproject.org We were looking forward to see you soon and it would be a pleasure to have you all at the first event of this kind. -- Regards Gerold Kassube Fedora Ambassador Deutschland / Germany Schweiz / Switzerland Email: GeroldKa at fedoraproject.org 1024D/F33128B9 4ABC A903 F1F4 D9CC C422 AACA EDF1 DF42 F331 28B9 -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 189 bytes Desc: Dies ist ein digital signierter Nachrichtenteil URL: From mcbeee at gmail.com Fri Nov 10 07:29:12 2006 From: mcbeee at gmail.com (Marc Bratmann) Date: Fri, 10 Nov 2006 08:29:12 +0100 Subject: Problem mit LVM nach Upgrade auf Core 6 Message-ID: Hallo zusammen, ich habe ?ber Anaconda ein Upgrade von Core 5 auf Core 6 vorgenommen. Das Upgrade lief fehlerfrei durch. Nach dem Reboot kommt nun folgender Fehler: > Logical Volume Management einrichten: 2 logical volume(s) in volume group "VolGroup00" noch active [OK] > Dateisysteme pr?fen [FEHLGESCHLAGEN] > > *** Beim ?berpr?fen des Dateisystems ist ein Fehler aufgetreten. > *** Sie werden zu einer Shell gef?hrt; [...] > (Dateisystem reparieren) 1# Wenn ich hier mal ein fsck starte, erhalte ich folgende Meldung: > Warnung... fsck.ext3 f?r Ger?t /dev/VolGroup00/LogVol00 wurde mit Signal 11 beendet. Kann ich das Problem mit dem LVM irgendwie ?ber diese Shell l?sen? ?brigens: Wenn ich einfach versuche wieder ?ber den grafischen Modus neu zu installieren, bleibt der Rechner mit schwarzem Bildschirm und einem gro?en X (Mauszeiger) noch vor dem ersten Menu h?ngen. Wie gehe ich denn jetzt am besten vor? Besten Gru?, Marc From fedora at wir-sind-cool.org Fri Nov 10 10:44:41 2006 From: fedora at wir-sind-cool.org (Michael Schwendt) Date: Fri, 10 Nov 2006 11:44:41 +0100 Subject: Problem mit LVM nach Upgrade auf Core 6 In-Reply-To: References: Message-ID: <20061110114441.80a7f22a.fedora@wir-sind-cool.org> On Fri, 10 Nov 2006 08:29:12 +0100, Marc Bratmann wrote: > Hallo zusammen, > > ich habe ?ber Anaconda ein Upgrade von Core 5 auf Core 6 vorgenommen. > Das Upgrade lief fehlerfrei durch. Nach dem Reboot kommt nun folgender > Fehler: > > > Logical Volume Management einrichten: 2 logical volume(s) in volume group "VolGroup00" noch active [OK] > > Dateisysteme pr?fen [FEHLGESCHLAGEN] > > > > *** Beim ?berpr?fen des Dateisystems ist ein Fehler aufgetreten. > > *** Sie werden zu einer Shell gef?hrt; [...] > > (Dateisystem reparieren) 1# > > Wenn ich hier mal ein fsck starte, erhalte ich folgende Meldung: > > > Warnung... fsck.ext3 f?r Ger?t /dev/VolGroup00/LogVol00 wurde mit Signal 11 beendet. > Hast Du auf diesem Rechner jemals memcheck durchlaufen lassen? Signal 11 ist ein "segmentation fault", also eines der ?belsten Probleme ?berhaupt, da es von instabiler Speicherhardware kommen und dann jede Software treffen kann. Sofern die Hardware als zuverl?ssig betrachtet werden kann, l?ge unsichere Programmierung in fsck.ext3 vor, die auf irgendeinen Sonderfall in den Arbeitsdaten nicht vorbereitet ist und daraufhin "etwas Dummes tut". From daniel at rindt.name Fri Nov 10 19:35:39 2006 From: daniel at rindt.name (Daniel Rindt) Date: Fri, 10 Nov 2006 20:35:39 +0100 Subject: Problem mit LVM nach Upgrade auf Core 6 In-Reply-To: References: Message-ID: <1163187339.3444.6.camel@luminary.homelinux.net> Am Freitag, den 10.11.2006, 08:29 +0100 schrieb Marc Bratmann: > Wenn ich hier mal ein fsck starte, erhalte ich folgende Meldung: > > > Warnung... fsck.ext3 f?r Ger?t /dev/VolGroup00/LogVol00 wurde mit > Signal 11 beendet. > > Kann ich das Problem mit dem LVM irgendwie ?ber diese Shell l?sen? Mein Vorschlag dazu w?re folgender: 1. Fedora Rescue System booten 2. Keine Fedora Installation suchen/ mounten lassen 3. fsck.* manuell durchf?hren 4. fs mounten und in /forcefsck l?schen 5. normales System starten Es l?st evtl. nicht das bestehende Problem aber man kommt vielleicht erstmal weiter. -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 189 bytes Desc: Dies ist ein digital signierter Nachrichtenteil URL: From fthommen at embl.de Mon Nov 13 11:53:08 2006 From: fthommen at embl.de (Frank Thommen) Date: Mon, 13 Nov 2006 12:53:08 +0100 Subject: Tausende von "illegal port" automounter-Fehlermeldungen Message-ID: <45585CA4.9030300@embl.de> Hallo, Ich habe einen Fedora Core 4-Client folgendermassen mit Automounter konfiguriert: /etc/auto.master: /home /etc/auto.home /etc/auto.home: * -rw,bg,intr myserver:/myhome/& Wenn ich nun auf dem Client ein nicht-existierendes File (z.B /home/afile) anspreche, versucht der Automounter ab dann *permanent*, dieses File anzusprechen. Das macht er, indem er offenbar den Mount ueber diverse - natuerlich illegale - Ports versucht. Damit fuellt er unsere Log-Partition auf (150'000 Zeilen in <3 Stunden): Nov 13 11:25:20 myserver rpc.mountd: refused mount request from myclient for /myhome/afile (/myhome): illegal port 43239 Die Portnummer variiert von Meldung zu Meldung Auf dem Client (aktuelles aufdatiertes und gepatchtes Fedora Core 4) sind autofs-4.1.4-26 and util-linux-2.12p-9.14 (fuer `mount`) installiert. Auf dem NFS-Server laeuft SuSE 9. Bin dankbar fuer jegliche Hilfe und Pointer. frank From tinsort-ng at yahoo.com Wed Nov 15 19:10:22 2006 From: tinsort-ng at yahoo.com (tinsort-ng at yahoo.com) Date: Wed, 15 Nov 2006 20:10:22 +0100 Subject: Update auf Fedora Core 6 steht still Message-ID: <1133883807.20061115201022@yahoo.com> Hi Ich habe mir die DVD Fedora Core 6 gebrannt und wollte nun ein Update von Core 5 machen. Doch Anaconda bleibt bei "Abh?ngigkeits?berpr?fung der zu installierenden Pakete" stehen - keine Fortschrittsanzeige. Oder geht das wirklich so lange? -- Gruss From frank-buettner at gmx.net Wed Nov 15 19:31:26 2006 From: frank-buettner at gmx.net (=?ISO-8859-1?Q?Frank_B=FCttner?=) Date: Wed, 15 Nov 2006 20:31:26 +0100 Subject: Update auf Fedora Core 6 steht still In-Reply-To: <1133883807.20061115201022@yahoo.com> References: <1133883807.20061115201022@yahoo.com> Message-ID: <455B6B0E.3020109@gmx.net> tinsort-ng at yahoo.com schrieb: > Hi > > Ich habe mir die DVD Fedora Core 6 gebrannt und wollte nun ein > Update von Core 5 machen. > > Doch Anaconda bleibt bei "Abh?ngigkeits?berpr?fung der zu > installierenden Pakete" stehen - keine Fortschrittsanzeige. > > Oder geht das wirklich so lange? > Das kann echt lange dauern. -------------- next part -------------- A non-text attachment was scrubbed... Name: smime.p7s Type: application/x-pkcs7-signature Size: 4285 bytes Desc: S/MIME Cryptographic Signature URL: From gerold at lugd.org Thu Nov 16 13:07:43 2006 From: gerold at lugd.org (Gerold Kassube) Date: Thu, 16 Nov 2006 14:07:43 +0100 Subject: REMINDER: Invitation to the FAD Message-ID: <1163682463.3349.27.camel@Amilo-GK.homenet.local> REGISTRATION CLOSE ON November, 18th ===================== you'll find it as PDF at http://fedoraproject.org/wiki/FAD?action=AttachFile&do=get&target=invite_FAD.pdf First FEDORA AMBASSADORS DAY (FAD EMEA) ======================================= The Fedora Ambassador Day (FAD) is where Ambassadors and other interested members of the Fedora Community come together to plan for future Fedora events and get to know each other. This is your chance to meet other Fedora community members (Ambassadors, Developers) in person. We are proud to invite you to the first FAD in EMEA. The Event will start date ==== December 1st, 2006 (6 pm GMT+1) till December 3rd, 2006 location ======== Werner Mennicke Haus R?hrberg e.V. Im Grossfeld 2 D-79639 Grenzach-Wyhlen - Germany - Agenda ====== Friday ------ afternoon: ?come together? Saturday -------- morning: Keynote from a FAMSCO Member small introduction of the participants afternoon: planning EMEA events for 2007 Breakout-sessions evening: Surprise event with local ?Linux Users? Sunday ------ if desired, visiting University of Basel with introduction in the used Red Hat Cluster Additional information * Accommodation * we have to pay per night and person EUR 5,50 / each. * We have the following rooms: -1- room with bunk bed, cupboard and washbasin -1- room with three bunk beds, cupboard and washbasin -4- rooms with each bunk bed, cupboard and washbasin -1- big room with five bunk beds and cupboards there are different showers and toilets. * You have to take care by your own for bed sheets, sleeping bag and your pillow. * Meals * Organized. Please indicate if you have special dietary requirements (vegetarian, allergies, ...) * Trip-planing * next airport Basel ? Mulhouse (international airport) * next railway-station L?rrach * best reachable railway-station Basel (Badischer Bahnhof) * by car Google Maps is your friend :) * Registration * please send your engaging registration latest November, 18th by E-Mail to GeroldKa at fedoraproject.org We were looking forward to see you soon and it would be a pleasure to have you all at the first event of this kind. -- Regards Gerold Kassube Fedora Ambassador Deutschland / Germany Schweiz / Switzerland Email: GeroldKa at fedoraproject.org 1024D/F33128B9 4ABC A903 F1F4 D9CC C422 AACA EDF1 DF42 F331 28B9 -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 189 bytes Desc: Dies ist ein digital signierter Nachrichtenteil URL: From tinsort-ng at yahoo.com Fri Nov 17 07:28:57 2006 From: tinsort-ng at yahoo.com (Martin) Date: Fri, 17 Nov 2006 08:28:57 +0100 Subject: Update auf Fedora Core 6 steht still In-Reply-To: <455B6B0E.3020109@gmx.net> References: <1133883807.20061115201022@yahoo.com> <455B6B0E.3020109@gmx.net> Message-ID: <20061117082857.515bad65@linuxserver.pfarrhaus> Hello Frank * Frank B?ttner, Wed, 15 Nov 2006 20:31:26 +0100: > > Oder geht das wirklich so lange? > > > Das kann echt lange dauern. Stimmt - ging ziemlich lang. Aber Ende gut, alles gut - so scheint es. Nach dem Update resp. nach dem Neukompilieren aller Pakete l?uft mein System stabil. Tolle Sache - bin begeistert! -- Martin