Ethernet

[bulent]

Jeff Vian wrote:

>
> So your problem is ???????
>
> bulent wrote:
>
>> Eric Diamond wrote:
>>
>>> Wednesday, April 07, 2004 3:57 AM Bülent Açy'kgöz
>>> wrote:
>>>  
>>>
>>>> Alexander Dalloz wrote:
>>>>
>>>>  
>>>>
>>>>>>       Link detected: no
>>>>>>       
>>>>>
>>>>>
>>>>>                            ^^^^^
>>>>> You see that? You have no link, thus you can not
>>>>>     
>>>>
>>>>
>>> successfully change 
>>>
>>>>> anything.
>>>>>
>>>>> ...snip...
>>>>>
>>>>> Still no link! Check your cables. Check the other
>>>>>     
>>>>
>>>>
>>> side of the cable, 
>>>
>>>>> check the plug in the switch/hub/router or where it
>>>>>     
>>>>
>>>>
>>> is.
>>>  
>>>
>>>> No I have link , Because I am downloading eveything
>>>>   
>>>
>>>
>>> also 
>>>
>>>> working samba and others.
>>>> Do you have any suggesstion?
>>>>
>>>>   
>>>
>>>
>>>
>>> Bülent,
>>>
>>> Could you please post your 'ifconfig -a' output?
>>>
>>> Eric Diamond
>>> eDiamond Networking & Security
>>> 303-246-9555
>>> eric at ediamond.net
>>>
>>>
>>>
>>>  
>>>
>> Hello, ifconfig output like this;
>>
>> [root at sbe-60 root]# ifconfig -a
>> eth0      Link encap:Ethernet  HWaddr 00:02:44:66:D3:32
>>          inet addr:144.122.85.60  Bcast:144.122.85.255  
>> Mask:255.255.255.0
>>          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
>>          RX packets:301403 errors:0 dropped:0 overruns:0 frame:0
>>          TX packets:115798 errors:14 dropped:0 overruns:0 carrier:0
>>          collisions:0 txqueuelen:1000
>>          RX bytes:51269291 (48.8 Mb)  TX bytes:119416712 (113.8 Mb)
>>          Interrupt:11 Base address:0xec00
>>
>> lo        Link encap:Local Loopback
>>          inet addr:127.0.0.1  Mask:255.0.0.0
>>          UP LOOPBACK RUNNING  MTU:16436  Metric:1
>>          RX packets:54794 errors:0 dropped:0 overruns:0 frame:0
>>          TX packets:54794 errors:0 dropped:0 overruns:0 carrier:0
>>          collisions:0 txqueuelen:0
>>          RX bytes:101928795 (97.2 Mb)  TX bytes:101928795 (97.2 Mb)
>>
>> also,
>> root at sbe-60 root]# mii-tool eth0
>> eth0: 10 Mbit, half duplex, no link
>> [root at sbe-60 root]# ping 144.122.199.20
>> PING 144.122.199.20 (144.122.199.20) 56(84) bytes of data.
>> 64 bytes from 144.122.199.20: icmp_seq=0 ttl=63 time=1.69 ms
>> 64 bytes from 144.122.199.20: icmp_seq=1 ttl=63 time=1.39 ms
>> 64 bytes from 144.122.199.20: icmp_seq=2 ttl=63 time=1.45 ms
>> 64 bytes from 144.122.199.20: icmp_seq=3 ttl=63 time=1.27 ms
>> 64 bytes from 144.122.199.20: icmp_seq=4 ttl=63 time=1.56 ms
>> 64 bytes from 144.122.199.20: icmp_seq=5 ttl=63 time=1.50 ms
>> 64 bytes from 144.122.199.20: icmp_seq=6 ttl=63 time=1.58 ms
>>
>>
>> Thank you...
>>
>
>
My porblem like this;

root at sbe-60 root]# mii-tool eth0
eth0: 10 Mbit, half duplex, no link

as you see, there is "no link" warning , what does  it mean?
and I didn't change 10Mbit to 100Mbit with mii-tool.
Do you have any suggestion?

-- 
Bülent Açikgöz
DBA & Sytem Administrator

Mobile: +90 532 5639505
Work  : +90 312 2103810
Adress: ODTU MM Binasi 3.Kat No:320 
Balgat/ANKARA/TURKIYE

There is no crueler tyranny than that which is perpetrated under the shield of law and in the name of justice.