sshd

Jeff Vian jvian10 at charter.net
Mon Aug 30 19:48:13 UTC 2004


On Mon, 2004-08-30 at 07:21, Tom Conway wrote:
> Thanks, the server is a used proliant. I've used them several time. This
> one had 2 nics in it and I assumed it would not be a problem since the
> cards were already installed. I've never had 2 nics at once. I assumed the
> intallation would handle it, didn't give it much thought... my error.
> 
> I'll give the ifdown/ifup a shot tonight.
> Where is the config file that I can comment out the "activate on boot" for
> eth1?
> 
> Thanks
> 

/etc/sysconfig/network-scripts/ifcfg-eth1

> > On Sun, 29 Aug 2004, Tom Conway wrote:
> >
> >> The issue is definetly network, my server has 2 cards,
> >> 192.168.0.15
> >> 192.168.0.20 (currently no cable connected)
> >>
> >>
> >> IP ROUTE
> >> 192.168.0.0/24 dev eth1  scope link
> >> 192.168.0.0/24 dev eth1  proto kernel  scope link  src 192.168.0.20
> >> 169.254.0.0/16 dev eth1  scope link
> >> 127.0.0.0/8 dev lo  scope link
> >> default via 192.168.0.1 dev eth1
> >                               ^^^^
> >
> > There is at least part of your problem. eth1 is the interface you said you
> > do not have a cable connected to. Try doing ifdown eth0, ifdown eth1, and
> > then do an ifup eth0. Then see what interface your default route is
> > through.
> > It should then be pointed at eth0.
> >
> > Question, why do you have 2 interfaces on the same network up at the same
> > time?
> > If you are planning to turn thei into a firewall then the addresses for
> > each
> > interface should be on 2 different networks.
> >
> >>
> >> IP ADDRESS
> >> 1: lo: <LOOPBACK,UP> mtu 16436 qdisc noqueue
> >>     link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
> >>     inet 127.0.0.1/8 brd 127.255.255.255 scope host lo
> >>     inet6 ::1/128 scope host
> >>        valid_lft forever preferred_lft forever
> >> 2: eth0: <BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast qlen 1000
> >>     link/ether 00:50:8b:d6:33:89 brd ff:ff:ff:ff:ff:ff
> >>     inet 192.168.0.15/24 brd 192.168.0.255 scope global eth0
> >>     inet6 fe80::250:8bff:fed6:3389/64 scope link
> >>        valid_lft forever preferred_lft forever
> >> 3: eth1: <BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast qlen 1000
> >>     link/ether 00:50:8b:ae:f5:f0 brd ff:ff:ff:ff:ff:ff
> >>     inet 192.168.0.20/24 brd 192.168.0.255 scope global eth1
> >            ^^^^^^^^^^^^^^^
> > You said there is no cable on this interface.
> >
> >>     inet6 fe80::250:8bff:feae:f5f0/64 scope link
> >>        valid_lft forever preferred_lft forever
> >> 4: sit0: <NOARP> mtu 1480 qdisc noop
> >>     link/sit 0.0.0.0 brd 0.0.0.0
> >
> > HTH,
> >
> > Tom
> >
> >
> > --
> > fedora-list mailing list
> > fedora-list at redhat.com
> > To unsubscribe: http://www.redhat.com/mailman/listinfo/fedora-list
> >
> 
> 
> -Later
> 





More information about the fedora-list mailing list