Ethernet card does not work with FC2
Alberto M R Davila
amrdavila at yahoo.com
Wed Jul 21 10:39:14 UTC 2004
Hi,
Good and bad to know I am not alone ! ;-)
I just checked my /etc/sysconfig/hwconf:
class: NETWORK
bus: PCI
detached: 0
device: eth0
driver: e100
desc: "Intel Corp.|82801BA/BAM/CA/CAM Ethernet Controller"
network.hwaddr: 00:00:39:DE:29:3F
vendorId: 8086
deviceId: 2449
subVendorId: 8086
subDeviceId: 3013
pciType: 1
pcidom: 0
pcibus: 2
pcidev: 8
pcifn: 0
-
-
class: NETWORK
bus: PCMCIA
detached: 96
device: eth1
driver: orinoco_cs
desc: "Intersil PRISM2 11 Mbps Wireless Adapter"
vendorId: 0156
deviceId: 0002
function: 0
slot: 0
Again apparently looks OK, unless the real experts let me know about any
problems.
I am missing my FC1 now, without eth0 up and working I cannot do my stuff.
Thanks for any further tips you may send.
Cheers, Alberto
--- "James A. Giseburt" <giseburt at molineschools.org> wrote:
> Good Day!
>
> I also have a Toshiba Satellite Pro 4600. As you stated, everything
> worked well with FC1. Not so with FC2.
>
> I am not having your problem with eth0 (the built-in ethernet adapter).
> I do have an alias in /etc/modprobe.conf for that adapter (alias eth0
> e100), but other than that it works.
>
> I am also having the problems that you describe with sound. I haven't
> been able to figure that out yet. I've checked all of the sound
> settings that I can find and I'm still looking. At this point, it would
> be nice to hear a simple beep, let alone music or some other audio.
>
> My only other problem is that my Cisco Aironet 350 PC Card doesn't
> work. It worked in FC1, but I haven't been able to get it to work with
> FC2. The system recognizes the card, but I haven't been able to
> activate the interface. I'm stumped at this point. Other people say
> that they have gotten this card to work, but not me. I've resorted to
> an old D-Link card (it pops right up).
>
> Sorry I haven't been of any help, but I just wanted to let you know that
> you are not alone.
>
>
> Jim
>
> James A. Giseburt
> Information Systems Manager E-mail: giseburt at molineschools.org
> Moline School District No. 40 Voice : 309.743.8990
> 2515 - 41st Street Fax : 309.743.8996
> Moline, IL 61265 Web : http://www.molineschools.org
>
>
>
> On Tue, 2004-07-20 at 20:37, Alberto M R Davila wrote:
> > Yes, I use static IP address and not DHCP... I was using FC1 nicely
> (with
> > my 512MB RAM and 60Gb HD) then assumed FC2 and its kernel 2.6 should
> run
> > nice as well... :-(
> >
> > >
> > > On Tue, 20 Jul 2004 17:56:30 -0700 (PDT), Alberto M R Davila
> > > <amrdavila at yahoo.com> wrote:
> > > > I just installed FC2 in my toshiba satellite 4600 laptop (pentium
> 3)
> > > and
> > > > the ethernet card is not working even the "redhat-config-network"
> > > shows
> > > > eth0 is "Active"... I tried a new installation (formatting
> > > partitions)
> > > > but it does not work as well... curiously during boot the eth0 is
> > > loaded
> > > > "OK". I tried the "linux rescue" boot with the disk 1 of FC2 and
> > > > nothing... but when I try the "linux rescue" of FC1 the eth0
> works...
> > > > "ping" from and to the laptop does not work. My "firewall" is
> enabled
> > > to
> > > > allow only SSH connections... btw, my sound card was not
> recognized
> > > after
> > > > installation as well, the test failed... any tips how I could
> > > conifgure
> > > > the eth0 manually ? Everything used to work fine when I was using
> FC1
> > > in
> > > > the same laptop ;-)
> > > >
> > > > Thanks for any tips you may send.
> > > >
> > > > Cheers, Alberto
> > > >
> > >
>
>
>
>
> --
> fedora-list mailing list
> fedora-list at redhat.com
> To unsubscribe: http://www.redhat.com/mailman/listinfo/fedora-list
>
__________________________________
Do you Yahoo!?
Vote for the stars of Yahoo!'s next ad campaign!
http://advision.webevents.yahoo.com/yahoo/votelifeengine/
More information about the fedora-list
mailing list