Fedora Core 2 and USB Ethernet DUB-E100 problem
J.P.M. van der Jagt
jeanpaul at dutepp0.et.tudelft.nl
Sun Jul 4 23:50:04 UTC 2004
Hello all,
I'm not sure if this is the right place to ask, so if not, then flames
are welcome :-) But I do hope that someone can help me with the
following situation.
Setup: Fedora Core 2, with most RPM updates installed (I think).
Box: VIA main board, type EPIA-M Mini-ITX, 256 MB memory.
Additional USB Ethernet adapter: D-Link DUB-E100, with ASIX 8817x chip.
(According to http://www.linux-usb.org/usbnet/ this USB Ethernet adapter
should be supported.)
The problem. During the boot phase, the D-Link DUB-E100 is recognised
by the system. If I have noticed correctly, the adapter is switched on
(i.e. the link LED turns on) during the starting up of either:
initialising usb controler [ehci_hcd]
or:
initialising usb controler [uhci_hcd]
The adapter is detected by the kernel as eth0, but gets
its name (eth1) and its IP address via the config file
/etc/sysconfig/network-scripts/ifcfg-eth1, with contents:
# D-link DUB-E100
DEVICE=eth1
BOOTPROTO=static
BROADCAST=192.168.10.255
HWADDR=00:40:05:90:AF:EC
IPADDR=192.168.10.20
NETMASK=255.255.255.0
NETWORK=192.168.10.0
ONBOOT=yes
TYPE=Ethernet
B.t.w. the on-board Ethernet interface is detected by the kernel as eth1,
but is set to eth0 by the /etc/sysconfig/network-scripts/ifcfg-eth0
config file.
The DUB-E100 then is perfectly usable, at least for a while. However,
after a certain uptime (this varies from two hours to ten hours), the
DUB-E100 suddenly stops functioning. Traffic is not possible anymore.
Unplugging and subsequently plugging-in of the DUB-E100 do not help.
The error that is then logged in /var/log/messages is:
usb 1-1: USB disconnect, address 2
Executing a "ifconfig down" succeeds, but an "ifconfig up" results in:
Error submitting the control message: status=-19
A shutdown of the box does not complete and hangs on shutting down the
interface (I think). The only way I got things running again is power
cycling the box.
I'll include the output of some commands here; may be this shines a
light on the problem. I'll also attach the complete /var/log/messages
file at the end of this message.
proxy:~ 46 # lsmod
Module Size Used by
ipv6 184672 12
parport_pc 19392 1
lp 8236 0
parport 29640 2 parport_pc,lp
autofs4 12932 0
sunrpc 109924 1
via_rhine 15752 0
floppy 47440 0
sg 27680 0
scsi_mod 91984 1 sg
dm_mod 32800 0
usbnet 19848 0
mii 3584 2 via_rhine,usbnet
uhci_hcd 24472 0
ehci_hcd 22916 0
button 4632 0
battery 6924 0
asus_acpi 8984 0
ac 3340 0
ext3 103656 3
jbd 40728 1 ext3
proxy:~ 47 # lsusb
Bus 004 Device 001: ID 0000:0000
Bus 003 Device 001: ID 0000:0000
Bus 002 Device 001: ID 0000:0000
Bus 001 Device 002: ID 2001:1a00 D-Link Corp. [hex]
Bus 001 Device 001: ID 0000:0000
proxy:~ 48 # usbmodules --device /proc/bus/usb/001/002
usbnet
proxy:~ 49 #
Note: sometimes "lsusb" hangs, just before it is supposed to list the
line with "D-Link Corp."; it then cannot be killed.
To rule out a hardware problem on the DUB-E100 I tried it under Windows
XP (on another box) and then the DUB-E100 keeps on functioning without
problems. I did not run Windows XP on the VIA box.
A thing that I noticed, when the DUB-E100 is in a non functioning state,
is that the link LED is still lit and also that the traffic LED still
blinks when traffic is received from the network. This would mean that
the DUB-E100 itself is still functioning (link level OK and remote ARP
entry still OK) and that the problem lies at the local end (kernel,
driver, USB port hardware, etcetera).
I've also ran a graphical tool called "usbview" and I'll list the output
at the end of this message. May be this is of some help.
So, finally, can please someone help me? Am I doing something wrong?
Is this a known problem? Is there a fix?
Thank you all in advance.
Best regards,
John-Paul (sysadmin)
--
usbview output:
|- UHCI Host Controller
|- UHCI Host Controller
|- UHCI Host Controller
|- EHCI Host Controller
|- DUB-E100 USB 2.0 Fast Etherne
DUB-E100 USB 2.0 Fast Etherne
Manufacturer:
Speed: 480Mb/s (high)
USB Version: 2.00
Device Class: 02(comm.)
Device Subclass: 00
Device Protocol: 00
Maximum Default Endpoint Size: 64
Number of Configurations: 1
Vendor Id: 2001
Product Id: 1a00
Revision Number: 0.01
Config Number: 1
Number of Interfaces: 1
Attributes: 80
MaxPower Needed: 450mA
Interface Number: 0
Name: usbnet
Alternate Number: 0
Class: 00(>ifc )
Sub Class: 0
Protocol: 0
Number of Endpoints: 3
Endpoint Address: 81
Direction: in
Attribute: 3
Type: Int.
Max Packet Size: 8
Interval: 128ms
Endpoint Address: 02
Direction: out
Attribute: 2
Type: Bulk
Max Packet Size: 512
Interval: 0ms
Endpoint Address: 83
Direction: in
Attribute: 2
Type: Bulk
Max Packet Size: 512
Interval: 0ms
--
/var/log/messages (note: the DUB-E100 here is plugged-in into the second
USB port instead of into the first; this makes no difference, except for
the logging entries)
Jul 5 00:46:23 proxy syslogd 1.4.1: restart.
Jul 5 00:46:23 proxy syslog: syslogd startup succeeded
Jul 5 00:46:23 proxy kernel: klogd 1.4.1, log source = /proc/kmsg started.
Jul 5 00:46:23 proxy kernel: Linux version 2.6.6-1.435 (bhcompile at tweety.build.redhat.com) (gcc version 3.3.3 20040412 (Red Hat Linux 3.3.3-7)) #1 Mon Jun 14 09:09:07 EDT 2004
Jul 5 00:46:23 proxy kernel: BIOS-provided physical RAM map:
Jul 5 00:46:23 proxy kernel: BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
Jul 5 00:46:23 proxy kernel: BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
Jul 5 00:46:23 proxy kernel: BIOS-e820: 0000000000100000 - 000000000eff0000 (usable)
Jul 5 00:46:23 proxy kernel: BIOS-e820: 000000000eff0000 - 000000000eff3000 (ACPI NVS)
Jul 5 00:46:23 proxy kernel: BIOS-e820: 000000000eff3000 - 000000000f000000 (ACPI data)
Jul 5 00:46:23 proxy kernel: BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
Jul 5 00:46:23 proxy kernel: 0MB HIGHMEM available.
Jul 5 00:46:23 proxy kernel: 239MB LOWMEM available.
Jul 5 00:46:23 proxy kernel: zapping low mappings.
Jul 5 00:46:23 proxy syslog: klogd startup succeeded
Jul 5 00:46:23 proxy kernel: On node 0 totalpages: 61424
Jul 5 00:46:23 proxy kernel: DMA zone: 4096 pages, LIFO batch:1
Jul 5 00:46:23 proxy kernel: Normal zone: 57328 pages, LIFO batch:13
Jul 5 00:46:23 proxy kernel: HighMem zone: 0 pages, LIFO batch:1
Jul 5 00:46:23 proxy kernel: DMI 2.2 present.
Jul 5 00:46:23 proxy kernel: ACPI: RSDP (v000 VT9174 ) @ 0x000f6560
Jul 5 00:46:23 proxy kernel: ACPI: RSDT (v001 VT9174 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x0eff3000
Jul 5 00:46:23 proxy kernel: ACPI: FADT (v001 VT9174 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x0eff3040
Jul 5 00:46:23 proxy kernel: ACPI: DSDT (v001 VT9174 AWRDACPI 0x00001000 MSFT 0x0100000c) @ 0x00000000
Jul 5 00:46:23 proxy kernel: ACPI: PM-Timer IO Port: 0x408
Jul 5 00:46:23 proxy kernel: Built 1 zonelists
Jul 5 00:46:23 proxy kernel: Kernel command line: ro root=LABEL=/ rhgb quiet
Jul 5 00:46:23 proxy kernel: mapped 4G/4G trampoline to ffff3000.
Jul 5 00:46:23 proxy kernel: Initializing CPU#0
Jul 5 00:46:23 proxy kernel: CPU 0 irqstacks, hard=02346000 soft=02345000
Jul 5 00:46:23 proxy kernel: PID hash table entries: 1024 (order 10: 8192 bytes)
Jul 5 00:46:23 proxy kernel: Detected 999.542 MHz processor.
Jul 5 00:46:23 proxy kernel: Using tsc for high-res timesource
Jul 5 00:46:23 proxy kernel: Console: colour VGA+ 80x25
Jul 5 00:46:23 proxy kernel: Memory: 240224k/245696k available (1552k kernel code, 4788k reserved, 603k data, 144k init, 0k highmem)
Jul 5 00:46:23 proxy kernel: Calibrating delay loop... 1974.27 BogoMIPS
Jul 5 00:46:23 proxy kernel: Security Scaffold v1.0.0 initialized
Jul 5 00:46:23 proxy kernel: SELinux: Initializing.
Jul 5 00:46:23 proxy kernel: SELinux: Starting in permissive mode
Jul 5 00:46:23 proxy kernel: There is already a security framework initialized, register_security failed.
Jul 5 00:46:23 proxy kernel: selinux_register_security: Registering secondary module capability
Jul 5 00:46:23 proxy irqbalance: irqbalance startup succeeded
Jul 5 00:46:23 proxy kernel: Capability LSM initialized as secondary
Jul 5 00:46:23 proxy kernel: Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Jul 5 00:46:23 proxy kernel: Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Jul 5 00:46:23 proxy kernel: Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Jul 5 00:46:23 proxy kernel: CPU: L1 I Cache: 64K (32 bytes/line), D cache 64K (32 bytes/line)
Jul 5 00:46:23 proxy kernel: CPU: L2 Cache: 64K (32 bytes/line)
Jul 5 00:46:23 proxy kernel: CPU: Centaur VIA Nehemiah stepping 03
Jul 5 00:46:23 proxy kernel: Enabling fast FPU save and restore... done.
Jul 5 00:46:23 proxy kernel: Enabling unmasked SIMD FPU exception support... done.
Jul 5 00:46:23 proxy kernel: Checking 'hlt' instruction... OK.
Jul 5 00:46:23 proxy kernel: checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Jul 5 00:46:23 proxy kernel: Freeing initrd memory: 186k freed
Jul 5 00:46:23 proxy kernel: NET: Registered protocol family 16
Jul 5 00:46:23 proxy kernel: PCI: PCI BIOS revision 2.10 entry at 0xfb260, last bus=1
Jul 5 00:46:23 proxy kernel: PCI: Using configuration type 1
Jul 5 00:46:23 proxy kernel: mtrr: v2.0 (20020519)
Jul 5 00:46:23 proxy kernel: ACPI: Subsystem revision 20040326
Jul 5 00:46:23 proxy kernel: ACPI: IRQ9 SCI: Level Trigger.
Jul 5 00:46:23 proxy kernel: ACPI: Interpreter enabled
Jul 5 00:46:23 proxy kernel: ACPI: Using PIC for interrupt routing
Jul 5 00:46:23 proxy kernel: ACPI: PCI Root Bridge [PCI0] (00:00)
Jul 5 00:46:23 proxy kernel: PCI: Probing PCI hardware (bus 00)
Jul 5 00:46:23 proxy kernel: ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
Jul 5 00:46:23 proxy kernel: ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 10 11 *12 14 15)
Jul 5 00:46:23 proxy kernel: ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 *10 11 12 14 15)
Jul 5 00:46:23 proxy kernel: ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 *5 6 7 10 11 12 14 15)
Jul 5 00:46:23 proxy kernel: Linux Plug and Play Support v0.97 (c) Adam Belay
Jul 5 00:46:23 proxy kernel: usbcore: registered new driver usbfs
Jul 5 00:46:23 proxy kernel: usbcore: registered new driver hub
Jul 5 00:46:23 proxy kernel: ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 12
Jul 5 00:46:23 proxy kernel: ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
Jul 5 00:46:23 proxy kernel: ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
Jul 5 00:46:23 proxy kernel: ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 5
Jul 5 00:46:23 proxy kernel: PCI: Using ACPI for IRQ routing
Jul 5 00:46:23 proxy kernel: vesafb: probe of vesafb0 failed with error -6
Jul 5 00:46:23 proxy kernel: apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
Jul 5 00:46:23 proxy kernel: apm: overridden by ACPI.
Jul 5 00:46:23 proxy kernel: audit: initializing netlink socket (disabled)
Jul 5 00:46:23 proxy kernel: audit(1088981127.4294966848:0): initialized
Jul 5 00:46:23 proxy kernel: Total HugeTLB memory allocated, 0
Jul 5 00:46:23 proxy kernel: VFS: Disk quotas dquot_6.5.1
Jul 5 00:46:23 proxy kernel: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Jul 5 00:46:23 proxy kernel: SELinux: Registering netfilter hooks
Jul 5 00:46:23 proxy kernel: Initializing Cryptographic API
Jul 5 00:46:23 proxy kernel: pci_hotplug: PCI Hot Plug PCI Core version: 0.5
Jul 5 00:46:23 proxy kernel: ACPI: Processor [CPU0] (supports C1 C2, 2 throttling states)
Jul 5 00:46:23 proxy kernel: isapnp: Scanning for PnP cards...
Jul 5 00:46:23 proxy kernel: isapnp: No Plug & Play device found
Jul 5 00:46:23 proxy kernel: Real Time Clock Driver v1.12
Jul 5 00:46:23 proxy kernel: Linux agpgart interface v0.100 (c) Dave Jones
Jul 5 00:46:23 proxy kernel: agpgart: Detected VIA PM266/KM266 chipset
Jul 5 00:46:23 proxy kernel: agpgart: Maximum main memory to use for agp memory: 189M
Jul 5 00:46:23 proxy kernel: agpgart: AGP aperture is 4M @ 0xe6000000
Jul 5 00:46:23 proxy kernel: Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing enabled
Jul 5 00:46:23 proxy kernel: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
Jul 5 00:46:23 proxy kernel: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
Jul 5 00:46:23 proxy portmap: portmap startup succeeded
Jul 5 00:46:23 proxy kernel: RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
Jul 5 00:46:23 proxy kernel: Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
Jul 5 00:46:23 proxy kernel: ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Jul 5 00:46:23 proxy kernel: VP_IDE: IDE controller at PCI slot 0000:00:11.1
Jul 5 00:46:23 proxy kernel: VP_IDE: chipset revision 6
Jul 5 00:46:23 proxy kernel: VP_IDE: not 100%% native mode: will probe irqs later
Jul 5 00:46:23 proxy kernel: VP_IDE: VIA vt8235 (rev 00) IDE UDMA133 controller on pci0000:00:11.1
Jul 5 00:46:23 proxy kernel: ide0: BM-DMA at 0xe000-0xe007, BIOS settings: hda:DMA, hdb:pio
Jul 5 00:46:23 proxy kernel: ide1: BM-DMA at 0xe008-0xe00f, BIOS settings: hdc:DMA, hdd:pio
Jul 5 00:46:23 proxy kernel: hda: Maxtor 6E040L0, ATA DISK drive
Jul 5 00:46:23 proxy kernel: Using cfq io scheduler
Jul 5 00:46:23 proxy kernel: ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Jul 5 00:46:23 proxy kernel: hdc: R/RW 8x4x32, ATAPI CD/DVD-ROM drive
Jul 5 00:46:23 proxy kernel: ide1 at 0x170-0x177,0x376 on irq 15
Jul 5 00:46:23 proxy kernel: hda: max request size: 128KiB
Jul 5 00:46:23 proxy kernel: hda: 80293248 sectors (41110 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(133)
Jul 5 00:46:23 proxy kernel: hda: hda1 hda2 hda3 hda4
Jul 5 00:46:23 proxy kernel: hdc: ATAPI 32X CD-ROM CD-R/RW drive, 2048kB Cache, DMA
Jul 5 00:46:23 proxy kernel: Uniform CD-ROM driver Revision: 3.20
Jul 5 00:46:23 proxy kernel: ide-floppy driver 0.99.newide
Jul 5 00:46:23 proxy kernel: usbcore: registered new driver hiddev
Jul 5 00:46:23 proxy kernel: usbcore: registered new driver usbhid
Jul 5 00:46:23 proxy kernel: drivers/usb/input/hid-core.c: v2.0:USB HID core driver
Jul 5 00:46:23 proxy kernel: mice: PS/2 mouse device common for all mice
Jul 5 00:46:23 proxy kernel: serio: i8042 AUX port at 0x60,0x64 irq 12
Jul 5 00:46:23 proxy kernel: serio: i8042 KBD port at 0x60,0x64 irq 1
Jul 5 00:46:23 proxy kernel: input: AT Translated Set 2 keyboard on isa0060/serio0
Jul 5 00:46:23 proxy kernel: md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
Jul 5 00:46:23 proxy kernel: NET: Registered protocol family 2
Jul 5 00:46:23 proxy rpc.statd[1822]: Version 1.0.6 Starting
Jul 5 00:46:23 proxy kernel: IP: routing cache hash table of 2048 buckets, 16Kbytes
Jul 5 00:46:23 proxy kernel: TCP: Hash tables configured (established 16384 bind 32768)
Jul 5 00:46:23 proxy kernel: Initializing IPsec netlink socket
Jul 5 00:46:23 proxy nfslock: rpc.statd startup succeeded
Jul 5 00:46:23 proxy kernel: NET: Registered protocol family 1
Jul 5 00:46:23 proxy kernel: NET: Registered protocol family 17
Jul 5 00:46:23 proxy kernel: ACPI: (supports S0 S1 S4 S5)
Jul 5 00:46:23 proxy kernel: md: Autodetecting RAID arrays.
Jul 5 00:46:23 proxy kernel: md: autorun ...
Jul 5 00:46:23 proxy kernel: md: ... autorun DONE.
Jul 5 00:46:23 proxy kernel: RAMDISK: Compressed image found at block 0
Jul 5 00:46:23 proxy kernel: VFS: Mounted root (ext2 filesystem).
Jul 5 00:46:23 proxy kernel: EXT3-fs: INFO: recovery required on readonly filesystem.
Jul 5 00:46:24 proxy kernel: EXT3-fs: write access will be enabled during recovery.
Jul 5 00:46:24 proxy kernel: kjournald starting. Commit interval 5 seconds
Jul 5 00:46:24 proxy kernel: EXT3-fs: recovery complete.
Jul 5 00:46:24 proxy kernel: EXT3-fs: mounted filesystem with ordered data mode.
Jul 5 00:46:24 proxy kernel: Freeing unused kernel memory: 144k freed
Jul 5 00:46:24 proxy kernel: SELinux: Disabled at runtime.
Jul 5 00:46:24 proxy kernel: SELinux: Unregistering netfilter hooks
Jul 5 00:46:24 proxy kernel: ACPI: Power Button (FF) [PWRF]
Jul 5 00:46:24 proxy kernel: ehci_hcd 0000:00:10.3: EHCI Host Controller
Jul 5 00:46:24 proxy kernel: ehci_hcd 0000:00:10.3: irq 5, pci mem 11822000
Jul 5 00:46:24 proxy kernel: ehci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 1
Jul 5 00:46:24 proxy kernel: ehci_hcd 0000:00:10.3: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10
Jul 5 00:46:24 proxy kernel: hub 1-0:1.0: USB hub found
Jul 5 00:46:24 proxy kernel: hub 1-0:1.0: 6 ports detected
Jul 5 00:46:24 proxy kernel: USB Universal Host Controller Interface driver v2.2
Jul 5 00:46:24 proxy kernel: uhci_hcd 0000:00:10.0: UHCI Host Controller
Jul 5 00:46:24 proxy kernel: uhci_hcd 0000:00:10.0: irq 11, io base 0000d400
Jul 5 00:46:24 proxy kernel: uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2
Jul 5 00:46:24 proxy kernel: hub 2-0:1.0: USB hub found
Jul 5 00:46:24 proxy kernel: hub 2-0:1.0: 2 ports detected
Jul 5 00:46:24 proxy kernel: usb 1-2: new high speed USB device using address 2
Jul 5 00:46:24 proxy kernel: uhci_hcd 0000:00:10.1: UHCI Host Controller
Jul 5 00:46:24 proxy kernel: uhci_hcd 0000:00:10.1: irq 12, io base 0000d800
Jul 5 00:46:24 proxy kernel: uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
Jul 5 00:46:24 proxy kernel: hub 3-0:1.0: USB hub found
Jul 5 00:46:24 proxy kernel: hub 3-0:1.0: 2 ports detected
Jul 5 00:46:24 proxy kernel: uhci_hcd 0000:00:10.2: UHCI Host Controller
Jul 5 00:46:24 proxy kernel: uhci_hcd 0000:00:10.2: irq 10, io base 0000dc00
Jul 5 00:46:24 proxy kernel: uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4
Jul 5 00:46:24 proxy kernel: hub 4-0:1.0: USB hub found
Jul 5 00:46:24 proxy kernel: hub 4-0:1.0: 2 ports detected
Jul 5 00:46:24 proxy kernel: eth0: register usbnet at usb-0000:00:10.3-2, DLink DUB-E100 USB Ethernet
Jul 5 00:46:24 proxy kernel: usbcore: registered new driver usbnet
Jul 5 00:46:24 proxy kernel: EXT3 FS on hda4, internal journal
Jul 5 00:46:24 proxy kernel: device-mapper: 4.1.0-ioctl (2003-12-10) initialised: dm at uk.sistina.com
Jul 5 00:46:24 proxy kernel: cdrom: open failed.
Jul 5 00:46:24 proxy kernel: Adding 1024120k swap on /dev/hda3. Priority:-1 extents:1
Jul 5 00:46:24 proxy kernel: kjournald starting. Commit interval 5 seconds
Jul 5 00:46:24 proxy kernel: EXT3 FS on hda1, internal journal
Jul 5 00:46:24 proxy kernel: EXT3-fs: mounted filesystem with ordered data mode.
Jul 5 00:46:24 proxy kernel: kjournald starting. Commit interval 5 seconds
Jul 5 00:46:24 proxy kernel: EXT3 FS on hda2, internal journal
Jul 5 00:46:24 proxy kernel: EXT3-fs: mounted filesystem with ordered data mode.
Jul 5 00:46:24 proxy kernel: parport0: PC-style at 0x378 [PCSPP,TRISTATE,EPP]
Jul 5 00:46:24 proxy kernel: SCSI subsystem initialized
Jul 5 00:46:24 proxy kernel: inserting floppy driver for 2.6.6-1.435
Jul 5 00:46:24 proxy kernel: Floppy drive(s): fd0 is 1.44M
Jul 5 00:46:24 proxy kernel: FDC 0 is a post-1991 82077
Jul 5 00:46:24 proxy kernel: ohci1394: $Rev: 1203 $ Ben Collins <bcollins at debian.org>
Jul 5 00:46:24 proxy kernel: ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[12] MMIO=[e6400000-e64007ff] Max Packet=[2048]
Jul 5 00:46:24 proxy kernel: via-rhine.c:v1.10-LK1.1.20-2.6 May-23-2004 Written by Donald Becker
Jul 5 00:46:24 proxy kernel: eth1: VIA VT6102 Rhine-II at 0xe6402000, 00:40:63:d3:b5:cb, IRQ 11.
Jul 5 00:46:24 proxy kernel: eth1: MII PHY found at address 1, status 0x7849 advertising 05e1 Link 0000.
Jul 5 00:46:24 proxy kernel: ip_tables: (C) 2000-2002 Netfilter core team
Jul 5 00:46:24 proxy last message repeated 2 times
Jul 5 00:46:20 proxy ifup:
Jul 5 00:46:20 proxy network: Bringing up interface eth0: succeeded
Jul 5 00:46:30 proxy rpcidmapd: rpc.idmapd startup succeeded
Jul 5 00:46:30 proxy random: Initializing random number generator: succeeded
Jul 5 00:46:31 proxy rc: Starting pcmcia: succeeded
Jul 5 00:46:31 proxy netfs: Mounting other filesystems: succeeded
Jul 5 00:46:31 proxy autofs: automount startup succeeded
Jul 5 00:46:31 proxy smartd[1942]: smartd version 5.21 Copyright (C) 2002-3 Bruce Allen
Jul 5 00:46:31 proxy smartd[1942]: Home page is http://smartmontools.sourceforge.net/
Jul 5 00:46:31 proxy smartd[1942]: Opened configuration file /etc/smartd.conf
Jul 5 00:46:31 proxy smartd[1942]: Configuration file /etc/smartd.conf parsed.
Jul 5 00:46:31 proxy smartd[1942]: Device: /dev/hda, opened
Jul 5 00:46:31 proxy smartd[1942]: Device: /dev/hda, not found in smartd database.
Jul 5 00:46:31 proxy smartd[1942]: Device: /dev/hda, is SMART capable. Adding to "monitor" list.
Jul 5 00:46:31 proxy smartd[1942]: Monitoring 1 ATA and 0 SCSI devices
Jul 5 00:46:31 proxy smartd[1944]: smartd has fork()ed into background mode. New PID=1944.
Jul 5 00:46:31 proxy smartd: smartd startup succeeded
Jul 5 00:46:32 proxy acpid: acpid startup succeeded
Jul 5 00:46:37 proxy kernel: parport0: PC-style at 0x378 [PCSPP,TRISTATE,EPP]
Jul 5 00:46:38 proxy kernel: lp0: using parport0 (polling).
Jul 5 00:46:38 proxy kernel: lp0: console ready
Jul 5 00:46:38 proxy cups: cupsd startup succeeded
Jul 5 00:46:38 proxy kernel: NET: Registered protocol family 10
Jul 5 00:46:38 proxy kernel: Disabled Privacy Extensions on device 022deac0(lo)
Jul 5 00:46:38 proxy kernel: IPv6 over IPv4 tunneling driver
Jul 5 00:46:38 proxy sshd: succeeded
Jul 5 00:46:39 proxy xinetd: xinetd startup succeeded
Jul 5 00:46:40 proxy sendmail: sendmail startup succeeded
Jul 5 00:46:40 proxy sendmail: sm-client startup succeeded
Jul 5 00:46:40 proxy xinetd[2191]: xinetd Version 2.3.13 started with libwrap loadavg options compiled in.
Jul 5 00:46:40 proxy xinetd[2191]: Started working: 1 available service
Jul 5 00:46:40 proxy crond: crond startup succeeded
Jul 5 00:46:41 proxy xfs: xfs startup succeeded
Jul 5 00:46:41 proxy anacron: anacron startup succeeded
Jul 5 00:46:41 proxy atd: atd startup succeeded
Jul 5 00:46:41 proxy messagebus: messagebus startup succeeded
Jul 5 00:46:42 proxy mdmonitor: mdadm succeeded
Jul 5 00:46:42 proxy mdmpd: mdmpd failed
--
More information about the fedora-list
mailing list