<solved>[RE: Cannot install FC2 or FC3-test1 on 29160 SCSIadapter (no html this time)]

[Alexander Lazarev]

Dear Sergio,

I have got quite interesting problem with Fedora Linux. When I installed
the Fedora Core 1 on 2-Xeon-processor machine with ServerWorks Grand
Champion SL chipset, everything was Ok. But when I tried to install the
Fedora Core 2, I received the "Unsupported ServerWorks chipset" message.
The vendor of motherboard (Tiger GC-SL S2727) is TYAN Computer
Corporation and I didn't find the proper support of this chipset for
Linux. Now, I would like to know if this chipset is being supported in
Fedora Core release 1.92 or Fedora Core release 2.90.

Thanks in advance.

Best Regards,

Alexander Lazarev
Systems Specialist
Systems and Database Support Unit
International Data Centre Division
CTBTO Preparatory Commission
Phone: + 43 1 260 30 6368
Fax: + 43 1 260 30 5932
Email: alexander.lazarev at ctbto.org
 

-----Original Message-----
From: fedora-list-bounces at redhat.com
[mailto:fedora-list-bounces at redhat.com] On Behalf Of Sergio fernandez
Sent: Thursday, July 22, 2004 10:33 AM
To: For users of Fedora Core releases
Subject: Re: <solved>[RE: Cannot install FC2 or FC3-test1 on 29160
SCSIadapter (no html this time)]


Hi mate
I have FC2 running on a Adaptec SCSI 19160 connected to a SCSI HD.  I
found that updating the Adaptec SCSI bios/firmware on the card helped.  
Also In the PC bios I set the primary chain detection to SCSI instead of
the default IDE.  I also updated the PC bios to the latest firmware.
Hope this helps




On 20 Jul 2004, at 20:17, Kartoz, Michael F wrote:

>> FC2 is not detecting my hard drive on a 29160 SCSI adapter during 
>> install.  Can anyone help?
>>
>> I'm trying to install FC2 on a machine with only 1 hard drive that is

>> attached to an Adaptec 29160 SCSI controller.  The AIC-7xxx driver is

>> automatically loading and is finding my adapter (I can see this by 
>> hitting <F4> while module is loading.  However, my disk drive is not 
>> found.  When I get to automatically partitioning, I get "no drives 
>> found".  I had no problems installing and running Redhat 9.0 
>> previously on this machine.  I also tried FC3-test1 but it didn't 
>> help.
>>
>> When I hit <F4> while AIC-7XXX module is loading on FC2, I get the
>> following:
>>   <6>PCI: Found IRQ 5 for device 0000:00:0d.0
>>   <6>scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
>>   <4>        <Adaptec 29160 Ultra160 SCSI adapter>
>>   <4>        aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
>>   <4>
>>   <4>(scsi0:A:0): 160.000MB/s transfers (80.000MHz DT, offset 63, 16
>> bit)
>>   <4>scsi0: Unexpected busfree while idle
>>   <4>SEQADDR == 0x1
>>
>
> The solution is to use noprobe when booting the install CD and then 
> manually add the aic7xxx_old driver (instead of aic7xxx).  I had seen 
> mention of using this driver to solve installation issues on older 
> Redhat distributions but could not find this driver on FC2.  Turns out

> that it is in there but appears alphabetically under "O" for Old 
> adaptec... and I was only looking in the "adaptec" section of the
list.
> Thanks to all who provided suggestions!
>
> -Mike
>
>
> --
> fedora-list mailing list
> fedora-list at redhat.com
> To unsubscribe: http://www.redhat.com/mailman/listinfo/fedora-list
>

Sergio Fernandez
Senior Technical Support

Albion - Internet Solutions for Business
Hp Centre of Excellence
www.albion.co.uk
Authorised AppleCentre
Tel: 020 7550 7550
Business Class ISP
fax: 020 7550 7551
Confidentiality Notice:- This email is intended only for the addressee. 
If you have received this email in error you are hereby notified that 
any use, copying or dissemination of this communication is prohibited 
as it may contain privileged and/or confidential information. Please 
telephone us immediately on 020 7550 7550 if you are not the intended 
recipient and destroy the original message.



-- 
fedora-list mailing list
fedora-list at redhat.com
To unsubscribe: http://www.redhat.com/mailman/listinfo/fedora-list