No Sound - FC2 - On board Abit-KV7

NiceBloke nicebloke at gmail.com
Thu Jun 24 13:29:45 UTC 2004 

Hi,

I just purchased a new motherboard and other hardware, so I thought
it's about time I upgraded to FC2 (doing a clean install). Everything
has gone as well as I'd expect - except that I haven't got any sound
:(

system-config-soundcard tells me the following audio device was detected:

Vendor: VIA Technologies
Modle: VT8233/A/8235/8237 AC97 Audio Controller
Module: snd-via82xx

If I try and play the test sound I get nothing through my speakers or
headphones (yep I did plug them back in - first thing I checked).

The only thing that I can see in dmesg that looks odd is:
irq 12: nobody cared! (screaming interrupt?)
Stack pointer is garbage, not printing trace
handlers:
[<02229291>] (i8042_interrupt+0x0/0xf5)
Disabling IRQ #12
serio: i8042 AUX port at 0x60,0x64 irq 12
irq 12: nobody cared! (screaming interrupt?)
Stack pointer is garbage, not printing trace
handlers:
[<02229291>] (i8042_interrupt+0x0/0xf5)
Disabling IRQ #12
irq 12: nobody cared! (screaming interrupt?)
Stack pointer is garbage, not printing trace
handlers:
[<02229291>] (i8042_interrupt+0x0/0xf5)
Disabling IRQ #12

However, if the complete dmesg is helpful then you can find it at the
end of this email.

[root at mybox]# uname -rv
2.6.6-1.435 #1 Mon Jun 14 09:09:07 EDT 2004

Any ideas? I'm not really sure where to start on this one :(


dmesg:

Linux version 2.6.6-1.435 (bhcompile at tweety.build.redhat.com) (gcc
version 3.3.3 20040412 (Red Hat Linux 3.3.3-7)) #1 Mon Jun 14 09:09:07
EDT 2004
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
 BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000001fef0000 (usable)
 BIOS-e820: 000000001fef0000 - 000000001fef3000 (ACPI NVS)
 BIOS-e820: 000000001fef3000 - 000000001ff00000 (ACPI data)
 BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
 BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
510MB LOWMEM available.
zapping low mappings.
On node 0 totalpages: 130800
  DMA zone: 4096 pages, LIFO batch:1
  Normal zone: 126704 pages, LIFO batch:16
  HighMem zone: 0 pages, LIFO batch:1
DMI 2.2 present.
ACPI: RSDP (v000 KT600                                     ) @ 0x000f7580
ACPI: RSDT (v001 KT600  AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fef3000
ACPI: FADT (v001 KT600  AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fef3040
ACPI: MADT (v001 KT600  AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fef7a00
ACPI: DSDT (v001 KT600  AWRDACPI 0x00001000 MSFT 0x0100000e) @ 0x00000000
ACPI: PM-Timer IO Port: 0x4008
Built 1 zonelists
Kernel command line: ro root=LABEL=/ rhgb quiet
mapped 4G/4G trampoline to ffff3000.
Initializing CPU#0
CPU 0 irqstacks, hard=02346000 soft=02345000
PID hash table entries: 2048 (order 11: 16384 bytes)
Detected 1852.292 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80x25
Memory: 515364k/523200k available (1552k kernel code, 7076k reserved,
603k data, 144k init, 0k highmem)
Calibrating delay loop... 3645.44 BogoMIPS
Security Scaffold v1.0.0 initialized
SELinux:  Initializing.
SELinux:  Starting in permissive mode
There is already a security framework initialized, register_security failed.
selinux_register_security:  Registering secondary module capability
Capability LSM initialized as secondary
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU:     After generic identify, caps: 0383fbff c1c3fbff 00000000 00000000
CPU:     After vendor identify, caps: 0383fbff c1c3fbff 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU:     After all inits, caps: 0383f3ff c1c3fbff 00000000 00000020
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: AMD Athlon(tm) XP 2500+ stepping 00
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 262k freed
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfaf40, last bus=1
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040326
ACPI: IRQ9 SCI: Level Trigger.
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 6 7 *10 11 12)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 6 7 10 *11 12)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 6 7 10 11 *12)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [ALKA] (IRQs 20) *0
ACPI: PCI Interrupt Link [ALKB] (IRQs 21) *0
ACPI: PCI Interrupt Link [ALKC] (IRQs 22) *0
ACPI: PCI Interrupt Link [ALKD] (IRQs 23) *0, disabled.
ACPI: Power Resource [PFAN] (off)
Linux Plug and Play Support v0.97 (c) Adam Belay
usbcore: registered new driver usbfs
usbcore: registered new driver hub
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 10
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 12
PCI: Using ACPI for IRQ routing
vesafb: probe of vesafb0 failed with error -6
apm: BIOS not found.
audit: initializing netlink socket (disabled)
audit(1088085710.280:0): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SELinux:  Registering netfilter hooks
Initializing Cryptographic API
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: Fan [FAN] (off)
ACPI: Processor [CPU0] (supports C1 C2)
ACPI: Thermal Zone [THRM] (40 C)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected VIA CLE266 chipset
agpgart: Maximum main memory to use for agp memory: 438M
agpgart: AGP aperture is 128M @ 0xe0000000
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
divert: not allocating divert_blk for non-ethernet device lo
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VIA8237SATA: IDE controller at PCI slot 0000:00:0f.0
VIA8237SATA: chipset revision 128
VIA8237SATA: 100% native mode on irq 10
    ide2: BM-DMA at 0xa000-0xa007, BIOS settings: hde:pio, hdf:pio
    ide3: BM-DMA at 0xa008-0xa00f, BIOS settings: hdg:pio, hdh:pio
VP_IDE: IDE controller at PCI slot 0000:00:0f.1
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1
    ide0: BM-DMA at 0xa800-0xa807, BIOS settings: hda:DMA, hdb:DMA
    ide1: BM-DMA at 0xa808-0xa80f, BIOS settings: hdc:DMA, hdd:DMA
hda: WDC WD1200JB-00CRA1, ATA DISK drive
hdb: PLEXTOR CD-R PX-W1210A, ATAPI CD/DVD-ROM drive
Using cfq io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hdc: _NEC DVD_RW ND-2510A, ATAPI CD/DVD-ROM drive
hdd: MAXTOR 6L040J2, ATA DISK drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 234441648 sectors (120034 MB) w/8192KiB Cache, CHS=65535/16/63, UDMA(100)
 hda: hda1 hda2 hda3
hdd: max request size: 128KiB
hdd: 78177792 sectors (40027 MB) w/1819KiB Cache, CHS=65535/16/63, UDMA(33)
 hdd: hdd1
hdb: ATAPI 32X CD-ROM CD-R/RW drive, 2048kB Cache, DMA
Uniform CD-ROM driver Revision: 3.20
hdc: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
ide-floppy driver 0.99.newide
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
mice: PS/2 mouse device common for all mice
irq 12: nobody cared! (screaming interrupt?)
Stack pointer is garbage, not printing trace
handlers:
[<02229291>] (i8042_interrupt+0x0/0xf5)
Disabling IRQ #12
serio: i8042 AUX port at 0x60,0x64 irq 12
irq 12: nobody cared! (screaming interrupt?)
Stack pointer is garbage, not printing trace
handlers:
[<02229291>] (i8042_interrupt+0x0/0xf5)
Disabling IRQ #12
irq 12: nobody cared! (screaming interrupt?)
Stack pointer is garbage, not printing trace
handlers:
[<02229291>] (i8042_interrupt+0x0/0xf5)
Disabling IRQ #12
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
ACPI: (supports S0 S1 S4 S5)
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
SCSI subsystem initialized
libata version 1.02 loaded.
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting.  Commit interval 5 seconds
EXT3-fs: hda2: orphan cleanup on readonly fs
ext3_orphan_cleanup: deleting unreferenced inode 114778
ext3_orphan_cleanup: deleting unreferenced inode 3113062
ext3_orphan_cleanup: deleting unreferenced inode 3113030
ext3_orphan_cleanup: deleting unreferenced inode 3112975
EXT3-fs: hda2: 4 orphan inodes deleted
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
Freeing unused kernel memory: 144k freed
SELinux:  Disabled at runtime.
SELinux:  Unregistering netfilter hooks
NET: Registered protocol family 10
Disabled Privacy Extensions on device 022deac0(lo)
IPv6 over IPv4 tunneling driver
divert: not allocating divert_blk for non-ethernet device sit0
ACPI: Power Button (FF) [PWRF]
ACPI: Sleep Button (CM) [SLPB]
ehci_hcd 0000:00:10.4: EHCI Host Controller
irq 12: nobody cared! (screaming interrupt?)
Stack pointer is garbage, not printing trace
handlers:
[<022169f4>] (usb_hcd_irq+0x0/0x4b)
Disabling IRQ #12
ehci_hcd 0000:00:10.4: irq 12, pci mem 22872000
ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:10.4: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
USB Universal Host Controller Interface driver v2.2
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: irq 10, io base 0000ac00
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: irq 10, io base 0000b000
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: irq 11, io base 0000b400
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
uhci_hcd 0000:00:10.3: UHCI Host Controller
uhci_hcd 0000:00:10.3: irq 11, io base 0000b800
uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 5
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
usb 2-1: new low speed USB device using address 2
EXT3 FS on hda2, internal journal
device-mapper: 4.1.0-ioctl (2003-12-10) initialised: dm at uk.sistina.com
cdrom: open failed.
cdrom: open failed.
Adding 1044216k swap on /dev/hda3.  Priority:-1 extents:1
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
drivers/usb/input/hid-core.c: ctrl urb status -2 received
drivers/usb/input/hid-core.c: timeout initializing reports

input: USB HID v1.00 Mouse [Logitech Inc. iFeel MouseMan] on usb-0000:00:10.0-1
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,EPP]
parport0: irq 7 detected
usb 5-2: new full speed USB device using address 2
inserting floppy driver for 2.6.6-1.435
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 2 if
0 alt 0 proto 2 vid 0x04B8 pid 0x0005
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
via-rhine.c:v1.10-LK1.1.20-2.6 May-23-2004 Written by Donald Becker
divert: allocating divert_blk for eth0
eth0: VIA VT6102 Rhine-II at 0xea001000, 00:50:8d:5d:5c:19, IRQ 10.
eth0: MII PHY found at address 1, status 0x7869 advertising 05e1 Link 0021.
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack version 2.1 (4087 buckets, 32696 max) - 296 bytes per conntrack
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,EPP]
parport0: irq 7 detected
lp0: using parport0 (polling).
lp0: console ready
eth0: no IPv6 routers present
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hdd1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
via82xx: Assuming DXS channels with 48k fixed sample rate.
         Please try dxs_support=1 or dxs_support=4 option
         and report if it works on your machine.
PCI: Setting latency timer of device 0000:00:11.5 to 64


Thanks in advance,
--  
Jim






--
NiceBloke

More information about the fedora-list mailing list