[Date Prev][Date Next]   [Thread Prev][Thread Next]   [Thread Index] [Date Index] [Author Index]

Re: AVM Fritz Card and capi



Thanks again Alexander

You are using HiSaX as well as trying CAPI. You can't use both at same
time. If you want to use CAPI then you have to avoid the loading of any
HiSaX module. You too have to get the CAPI closed source tarball from
the AVM ftp server.

I have no Fritz PCI card, so I can't test it myself on FC2. Following is
the list of CAPI related modules I have on another system:

capidrv                27188   2
isdn                  130048   2  [capidrv]
fcclassic             584256   4
capi                   19936   6
capifs                  5036   1  [capi]
kernelcapi             33248   6  [capidrv fcclassic capi]
capiutil               24544   0  [capidrv kernelcapi]

You don't need necessarily capidrv, and fcclassic is the module for my
old ISA Fritz card.

Alexander

I downloaded the tarball from AVM and ran ./install which reported:- [root Vigor11 fritz]# ./install

Welcome to the FRITZ!Card PCI driver installation!

Generating FRITZ!Card PCI driver for kernel 2.6.8-1.521...
Copying FRITZ!Card PCI driver...
 src/fcpci.ko to /lib/modules/2.6.8-1.521/extra/fcpci.ko

The driver files have been copied.

Ready

[root Vigor11 fritz]#

I then changed /etc/sysconf/isdncard to:-
RESOURCES='protocol=2 type=27 id=HiSax'
NAME='AVM PCI (Fritz!PCI)'
MODULE=fcpci
VENDOR_ID=1244
FIRMWARE=

I guess that this is not correct - how do I find the correct settings?

When I reboot my log says:-
Oct 17 09:36:20 vigor11 kernel: CAPI Subsystem Rev 1.1.2.8
Oct 17 09:36:20 vigor11 kernel: fcpci: module license 'Proprietary' taints kernel.
Oct 17 09:36:20 vigor11 kernel: fcpci: Unknown parameter `protocol'
Oct 17 09:36:20 vigor11 kernel: fcpci: AVM FRITZ!Card PCI driver, revision 0.6.2
Oct 17 09:36:20 vigor11 kernel: fcpci: (fcpci built on Oct 17 2004 at 09:31:17)
Oct 17 09:36:20 vigor11 kernel: ACPI: PCI interrupt 0000:02:05.0[A] -> GSI 5 (level, low) -> IRQ 5
Oct 17 09:36:20 vigor11 kernel: fcpci: AVM FRITZ!Card PCI found: port 0x3000, irq 5
Oct 17 09:36:20 vigor11 kernel: fcpci: Loading...
Oct 17 09:36:20 vigor11 kernel: fcpci: Driver 'fcpci' attached to stack. (152)
Oct 17 09:36:20 vigor11 kernel: fcpci: Stack version 3.11-02
Oct 17 09:36:20 vigor11 kernel: kcapi: Controller 1: fcpci-3000-05 attached
Oct 17 09:36:20 vigor11 kernel: kcapi: card 1 "fcpci-3000-05" ready.
Oct 17 09:36:20 vigor11 kernel: fcpci: Loaded.
Oct 17 09:36:20 vigor11 kernel: fcpci: Removing...
Oct 17 09:36:20 vigor11 kernel: kcapi: card 1 down.
Oct 17 09:36:21 vigor11 kernel: kcapi: Controller 1: fcpci-3000-05 unregistered
Oct 17 09:36:21 vigor11 kernel: fcpci: Removed.
Oct 17 09:36:21 vigor11 kernel: fcpci: Driver 'fcpci' detached
Any ideas


I also cannot find the capiutil module

Ian





[Date Prev][Date Next]   [Thread Prev][Thread Next]   [Thread Index] [Date Index] [Author Index]