sata_sx4 Issues

Ruben Moretti moretti at labor-enders.de
Wed Aug 31 10:00:28 UTC 2005


> Hello List & Co ;)
>
> I'm running 2.6.12 /2.6.13 kernel on a single CPU (P4-Celeron)/Fedora. 
> Board  ASROCK 775V88 with 2 Sata ports onboard. (sata_via)
> With two promise SX4 cards serving seven SATA HDs on their seven channels 
> (RAID). [Card1 Port 2,3,4  - Card2 Port 2,3,4]
> Now  I added  HDDs to the controller 1 or 2. All HDs are connected as 
> master; one HD per channel.
> Now wenn i add the HDDs on  Ports 1, I get errors for the  added HD,  and 
> for the previously installed ones.
> There's no irq problem and no HD or controller problem (checked this by 
> cross-changing).
> Tested with kernels 2.6.12 /2.6.13
> Log File, one with and one without HDD on Port 1 [Both Cards with HDDs on 
> Port 2,3,4]
>
> Any more ideas?
> Thanks in advance
>
> Ruben Moretti
>
>
>
> --- Snip with HDD on Port 1 Card 1
> Linux version 2.6.12-1.1447_FC4 (bhcompile at decompose.build.redhat.com) 
> (gcc version 4.0.1 20050727 (Red Hat 4.0.1-5)) #1 Fri Aug 26 20:29:51 EDT 
> 2005
> BIOS-provided physical RAM map:
> BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
> BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
> BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
> BIOS-e820: 0000000000100000 - 000000003ffb0000 (usable)
> BIOS-e820: 000000003ffb0000 - 000000003ffc0000 (ACPI data)
> BIOS-e820: 000000003ffc0000 - 000000003fff0000 (ACPI NVS)
> BIOS-e820: 000000003fff0000 - 0000000040000000 (reserved)
> BIOS-e820: 00000000fffc0000 - 0000000100000000 (reserved)
> 127MB HIGHMEM available.
> 896MB LOWMEM available.
> Using x86 segment limits to approximate NX protection
> DMI 2.3 present.
> Allocating PCI resources starting at 40000000 (gap: 40000000:bffc0000)
> Built 1 zonelists
> Kernel command line: ro root=/dev/md3 acpi=off pci=noacpi ide=nodma 
> console=ttyS0 console=tty0
> ide_setup: ide=nodma : Prevented DMA
> Initializing CPU#0
> CPU 0 irqstacks, hard=c0458000 soft=c0457000
> PID hash table entries: 4096 (order: 12, 65536 bytes)
> Detected 2684.955 MHz processor.
> Using tsc for high-res timesource
> Console: colour VGA+ 80x25
> Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
> Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
> Memory: 1033384k/1048256k available (2518k kernel code, 14048k reserved, 
> 690k data, 184k init, 130752k highmem)
> Checking if this processor honours the WP bit even in supervisor mode... 
> Ok.
> Security Framework v1.0.0 initialized
> SELinux:  Initializing.
> SELinux:  Starting in permissive mode
> selinux_register_security:  Registering secondary module capability
> Capability LSM initialized as secondary
> Mount-cache hash table entries: 512
> monitor/mwait feature present.
> using mwait in idle threads.
> CPU: Trace cache: 12K uops, L1 D cache: 16K
> CPU: L2 cache: 256K
> Intel machine check architecture supported.
> Intel machine check reporting enabled on CPU#0.
> CPU0: Intel P4/Xeon Extended MCE MSRs (24) available
> CPU: Intel(R) Celeron(R) CPU 2.80GHz stepping 01
> Enabling fast FPU save and restore... done.
> Enabling unmasked SIMD FPU exception support... done.
> Checking 'hlt' instruction... OK.
> checking if image is initramfs... it is
> Freeing initrd memory: 1199k freed
> NET: Registered protocol family 16
> PCI: Using configuration type 1
> mtrr: v2.0 (20020519)
> ACPI: Subsystem revision 20050729
> ACPI: Interpreter disabled.
> Linux Plug and Play Support v0.97 (c) Adam Belay
> pnp: PnP ACPI: disabled
> usbcore: registered new driver usbfs
> usbcore: registered new driver hub
> PCI: Probing PCI hardware
> PCI: Probing PCI hardware (bus 00)
> PCI: Using IRQ router default [1106/3227] at 0000:00:11.0
> PCI: IRQ 0 for device 0000:00:0f.1 doesn't match PIRQ mask - try 
> pci=usepirqmask
> apm: BIOS not found.
> audit: initializing netlink socket (disabled)
> audit(1125392498.474:1): initialized
> highmem bounce pool size: 64 pages
> Total HugeTLB memory allocated, 0
> VFS: Disk quotas dquot_6.5.1
> Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
> SELinux:  Registering netfilter hooks
> Initializing Cryptographic API
> ksign: Installing public key data
> Loading keyring
> - Added public key 1C1942C715575330
> - User ID: Red Hat, Inc. (Kernel Module GPG key)
> pci_hotplug: PCI Hot Plug PCI Core version: 0.5
> isapnp: Scanning for PnP cards...
> isapnp: No Plug & Play device found
> Real Time Clock Driver v1.12
> Linux agpgart interface v0.101 (c) Dave Jones
> agpgart: Detected VIA PT880 chipset
> agpgart: AGP aperture is 64M @ 0xf8000000
> PNP: No PS/2 controller found. Probing ports directly.
> serio: i8042 AUX port at 0x60,0x64 irq 12
> serio: i8042 KBD port at 0x60,0x64 irq 1
> Serial: 8250/16550 driver $Revision: 1.90 $ 76 ports, IRQ sharing enabled
> ÿttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
> io scheduler noop registered
> io scheduler anticipatory registered
> io scheduler deadline registered
> io scheduler cfq registered
> RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
> Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
> ide: Assuming 33MHz system bus speed for PIO modes; override with 
> idebus=xx
> VP_IDE: IDE controller at PCI slot 0000:00:0f.1
> PCI: IRQ 0 for device 0000:00:0f.1 doesn't match PIRQ mask - try 
> pci=usepirqmask
> PCI: Via IRQ fixup for 0000:00:0f.1, from 255 to 0
> VP_IDE: chipset revision 6
> VP_IDE: not 100% native mode: will probe irqs later
> VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1
>    ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:pio
>    ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:DMA
> hda: WDC WD400BB-23DEA0, ATA DISK drive
> ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
> hdc: WDC WD400BB-23DEA0, ATA DISK drive
> hdd: GCR-8523B, ATAPI CD/DVD-ROM drive
> ide1 at 0x170-0x177,0x376 on irq 15
> hda: max request size: 128KiB
> hda: Host Protected Area detected.
>        current capacity is 78156288 sectors (40016 MB)
>        native  capacity is 78165360 sectors (40020 MB)
> hda: Host Protected Area disabled.
> hda: 78165360 sectors (40020 MB) w/2048KiB Cache, CHS=65535/16/63
> hda: cache flushes not supported
> hda: hda1 hda2 hda3
> hdc: max request size: 128KiB
> hdc: Host Protected Area detected.
>        current capacity is 78156288 sectors (40016 MB)
>        native  capacity is 78165360 sectors (40020 MB)
> hdc: Host Protected Area disabled.
> hdc: 78165360 sectors (40020 MB) w/2048KiB Cache, CHS=65535/16/63
> hdc: cache flushes not supported
> hdc: hdc1 hdc2 hdc3
> hdd: ATAPI 52X CD-ROM drive, 128kB Cache
> Uniform CD-ROM driver Revision: 3.20
> ide-floppy driver 0.99.newide
> usbcore: registered new driver hiddev
> usbcore: registered new driver usbhid
> drivers/usb/input/hid-core.c: v2.01:USB HID core driver
> mice: PS/2 mouse device common for all mice
> md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
> NET: Registered protocol family 2
> IP: routing cache hash table of 2048 buckets, 64Kbytes
> TCP established hash table entries: 262144 (order: 9, 2097152 bytes)
> TCP bind hash table entries: 65536 (order: 8, 1835008 bytes)
> TCP: Hash tables configured (established 262144 bind 65536)
> Initializing IPsec netlink socket
> NET: Registered protocol family 1
> NET: Registered protocol family 17
> Freeing unused kernel memory: 184k freed
> input: AT Translated Set 2 keyboard on isa0060/serio0
> SCSI subsystem initialized
> sata_via(0000:00:0f.0): routed to hard irq line 10
> ata1: SATA max UDMA/133 cmd 0xEC00 ctl 0xE802 bmdma 0xDC00 irq 10
> ata2: SATA max UDMA/133 cmd 0xE400 ctl 0xE002 bmdma 0xDC08 irq 10
> logips2pp: Detected unknown logitech mouse model 1
> input: ImPS/2 Logitech Wheel Mouse on isa0060/serio1
> ata1: dev 0 ATA, max UDMA/133, 398297088 sectors: lba48
> ata1: dev 0 configured for UDMA/133
> scsi0 : sata_via
> ata2: dev 0 ATA, max UDMA/133, 398297088 sectors: lba48
> ata2: dev 0 configured for UDMA/133
> scsi1 : sata_via
>  Vendor: ATA       Model: Maxtor 6L200M0    Rev: BANC
>  Type:   Direct-Access                      ANSI SCSI revision: 05
> SCSI device sda: 398297088 512-byte hdwr sectors (203928 MB)
> SCSI device sda: drive cache: write back
> SCSI device sda: 398297088 512-byte hdwr sectors (203928 MB)
> SCSI device sda: drive cache: write back
> sda: sda1
> Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
>  Vendor: ATA       Model: Maxtor 6L200M0    Rev: BANC
>  Type:   Direct-Access                      ANSI SCSI revision: 05
> SCSI device sdb: 398297088 512-byte hdwr sectors (203928 MB)
> SCSI device sdb: drive cache: write back
> SCSI device sdb: 398297088 512-byte hdwr sectors (203928 MB)
> SCSI device sdb: drive cache: write back
> sdb: sdb1
> Attached scsi disk sdb at scsi1, channel 0, id 0, lun 0
> Local DIMM ECC Enabled
> ata3: SATA max UDMA/133 cmd 0xF89C0200 ctl 0xF89C0238 bmdma 0x0 irq 5
> ata4: SATA max UDMA/133 cmd 0xF89C0280 ctl 0xF89C02B8 bmdma 0x0 irq 5
> ata5: SATA max UDMA/133 cmd 0xF89C0300 ctl 0xF89C0338 bmdma 0x0 irq 5
> ata6: SATA max UDMA/133 cmd 0xF89C0380 ctl 0xF89C03B8 bmdma 0x0 irq 5
> ata3: dev 0 ATA, max UDMA/133, 398297088 sectors: lba48
> ata3: dev 0 configured for UDMA/133
> scsi2 : sata_sx4
> ata4: dev 0 ATA, max UDMA/133, 398297088 sectors: lba48
> ata4: dev 0 configured for UDMA/133
> scsi3 : sata_sx4
> ata5: dev 0 ATA, max UDMA/133, 398297088 sectors: lba48
> ata5: dev 0 configured for UDMA/133
> scsi4 : sata_sx4
> ata6: dev 0 ATA, max UDMA/133, 398297088 sectors: lba48
> ata6: dev 0 configured for UDMA/133
> scsi5 : sata_sx4
>  Vendor: ATA       Model: Maxtor 6L200M0    Rev: BANC
>  Type:   Direct-Access                      ANSI SCSI revision: 05
> SCSI device sdc: 398297088 512-byte hdwr sectors (203928 MB)
> SCSI device sdc: drive cache: write back
> SCSI device sdc: 398297088 512-byte hdwr sectors (203928 MB)
> SCSI device sdc: drive cache: write back
> sdc:<3>ata3: command timeout
> ata3: status=0x51 { DriveReady SeekComplete Error }
> ata3: called with no error (51)!
> SCSI error : <2 0 0 0> return code = 0x8000002
> sdc: Current: sense key: Medium Error
>    Additional sense: Unrecovered read error - auto reallocate failed
> end_request: I/O error, dev sdc, sector 8
> Buffer I/O error on device sdc, logical block 1
> ata3: command timeout
> ata3: status=0x51 { DriveReady SeekComplete Error }
> ata3: called with no error (51)!
> SCSI error : <2 0 0 0> return code = 0x8000002
> sdc: Current: sense key: Medium Error
>    Additional sense: Unrecovered read error - auto reallocate failed
> end_request: I/O error, dev sdc, sector 8
> Buffer I/O error on device sdc, logical block 1
> Dev sdc: unable to read RDB block 8
> unknown partition table
> Attached scsi disk sdc at scsi2, channel 0, id 0, lun 0
>  Vendor: ATA       Model: Maxtor 6L200M0    Rev: BANC
>  Type:   Direct-Access                      ANSI SCSI revision: 05
> SCSI device sdd: 398297088 512-byte hdwr sectors (203928 MB)
> SCSI device sdd: drive cache: write back
> SCSI device sdd: 398297088 512-byte hdwr sectors (203928 MB)
> SCSI device sdd: drive cache: write back
> sdd:<3>ata4: command timeout
> ata4: status=0x51 { DriveReady SeekComplete Error }
> ata4: called with no error (51)!
> SCSI error : <3 0 0 0> return code = 0x8000002
> sdd: Current: sense key: Medium Error
>    Additional sense: Unrecovered read error - auto reallocate failed
> end_request: I/O error, dev sdd, sector 0
> Buffer I/O error on device sdd, logical block 0
> ata4: command timeout
> ata4: status=0x51 { DriveReady SeekComplete Error }
> ata4: called with no error (51)!
> SCSI error : <3 0 0 0> return code = 0x8000002
> sdd: Current: sense key: Medium Error
>    Additional sense: Unrecovered read error - auto reallocate failed
> end_request: I/O error, dev sdd, sector 0
> Buffer I/O error on device sdd, logical block 0
> ata4: command timeout
> ata4: status=0x51 { DriveReady SeekComplete Error }
> ata4: called with no error (51)!
> SCSI error : <3 0 0 0> return code = 0x8000002
> sdd: Current: sense key: Medium Error
>    Additional sense: Unrecovered read error - auto reallocate failed
> end_request: I/O error, dev sdd, sector 0
> Buffer I/O error on device sdd, logical block 0
> unable to read partition table
> Attached scsi disk sdd at scsi3, channel 0, id 0, lun 0
>  Vendor: ATA       Model: Maxtor 6L200M0    Rev: BANC
>  Type:   Direct-Access                      ANSI SCSI revision: 05
> SCSI device sde: 398297088 512-byte hdwr sectors (203928 MB)
> SCSI device sde: drive cache: write back
> SCSI device sde: 398297088 512-byte hdwr sectors (203928 MB)
> SCSI device sde: drive cache: write back
> sde:<3>ata5: command timeout
> ata5: status=0x51 { DriveReady SeekComplete Error }
> ata5: called with no error (51)!
> SCSI error : <4 0 0 0> return code = 0x8000002
> sde: Current: sense key: Medium Error
>    Additional sense: Unrecovered read error - auto reallocate failed
> end_request: I/O error, dev sde, sector 0
> Buffer I/O error on device sde, logical block 0
> ata5: command timeout
> ata5: status=0x51 { DriveReady SeekComplete Error }
> ata5: called with no error (51)!
> SCSI error : <4 0 0 0> return code = 0x8000002
> sde: Current: sense key: Medium Error
>    Additional sense: Unrecovered read error - auto reallocate failed
> end_request: I/O error, dev sde, sector 0
> Buffer I/O error on device sde, logical block 0
> ata5: command timeout
> ata5: status=0x51 { DriveReady SeekComplete Error }
> ata5: called with no error (51)!
> SCSI error : <4 0 0 0> return code = 0x8000002
> sde: Current: sense key: Medium Error
>    Additional sense: Unrecovered read error - auto reallocate failed
> end_request: I/O error, dev sde, sector 0
> Buffer I/O error on device sde, logical block 0
> unable to read partition table
> Attached scsi disk sde at scsi4, channel 0, id 0, lun 0
>  Vendor: ATA       Model: Maxtor 6L200M0    Rev: BANC
>  Type:   Direct-Access                      ANSI SCSI revision: 05
> SCSI device sdf: 398297088 512-byte hdwr sectors (203928 MB)
> SCSI device sdf: drive cache: write back
> SCSI device sdf: 398297088 512-byte hdwr sectors (203928 MB)
> SCSI device sdf: drive cache: write back
> sdf:<3>ata6: command timeout
> ata6: status=0x51 { DriveReady SeekComplete Error }
> ata6: called with no error (51)!
> SCSI error : <5 0 0 0> return code = 0x8000002
> sdf: Current: sense key: Medium Error
>    Additional sense: Unrecovered read error - auto reallocate failed
> end_request: I/O error, dev sdf, sector 0
> Buffer I/O error on device sdf, logical block 0
> ata6: command timeout
> ata6: status=0x51 { DriveReady SeekComplete Error }
> ata6: called with no error (51)!
> SCSI error : <5 0 0 0> return code = 0x8000002
> sdf: Current: sense key: Medium Error
>    Additional sense: Unrecovered read error - auto reallocate failed
> end_request: I/O error, dev sdf, sector 0
> Buffer I/O error on device sdf, logical block 0
> ata6: command timeout
> ata6: status=0x51 { DriveReady SeekComplete Error }
> ata6: called with no error (51)!
> SCSI error : <5 0 0 0> return code = 0x8000002
> sdf: Current: sense key: Medium Error
>    Additional sense: Unrecovered read error - auto reallocate failed
> end_request: I/O error, dev sdf, sector 0
> Buffer I/O error on device sdf, logical block 0
> unable to read partition table
> Attached scsi disk sdf at scsi5, channel 0, id 0, lun 0
> Local DIMM ECC Enabled
> ata7: SATA max UDMA/133 cmd 0xF8B40200 ctl 0xF8B40238 bmdma 0x0 irq 10
> ata8: SATA max UDMA/133 cmd 0xF8B40280 ctl 0xF8B402B8 bmdma 0x0 irq 10
> ata9: SATA max UDMA/133 cmd 0xF8B40300 ctl 0xF8B40338 bmdma 0x0 irq 10
> ata10: SATA max UDMA/133 cmd 0xF8B40380 ctl 0xF8B403B8 bmdma 0x0 irq 10
> ATA: abnormal status 0x7F on port 0xF8B4021C
> scsi6 : sata_sx4
> ata8: dev 0 ATA, max UDMA/133, 398297088 sectors: lba48
> ata8: dev 0 configured for UDMA/133
> scsi7 : sata_sx4
> ata9: dev 0 ATA, max UDMA/133, 398297088 sectors: lba48
> ata9: dev 0 configured for UDMA/133
> scsi8 : sata_sx4
> ata10: dev 0 ATA, max UDMA/133, 398297088 sectors: lba48
> ata10: dev 0 configured for UDMA/133
> scsi9 : sata_sx4
>  Vendor: ATA       Model: Maxtor 6L200M0    Rev: BANC
>  Type:   Direct-Access                      ANSI SCSI revision: 05
> SCSI device sdg: 398297088 512-byte hdwr sectors (203928 MB)
> SCSI device sdg: drive cache: write back
> SCSI device sdg: 398297088 512-byte hdwr sectors (203928 MB)
> SCSI device sdg: drive cache: write back
> sdg: unknown partition table
> Attached scsi disk sdg at scsi7, channel 0, id 0, lun 0
>  Vendor: ATA       Model: Maxtor 6L200M0    Rev: BANC
>  Type:   Direct-Access                      ANSI SCSI revision: 05
> SCSI device sdh: 398297088 512-byte hdwr sectors (203928 MB)
> SCSI device sdh: drive cache: write back
> SCSI device sdh: 398297088 512-byte hdwr sectors (203928 MB)
> SCSI device sdh: drive cache: write back
> sdh: sdh1
> Attached scsi disk sdh at scsi8, channel 0, id 0, lun 0
>  Vendor: ATA       Model: Maxtor 6L200M0    Rev: BANC
>  Type:   Direct-Access                      ANSI SCSI revision: 05
> SCSI device sdi: 398297088 512-byte hdwr sectors (203928 MB)
> SCSI device sdi: drive cache: write back
> SCSI device sdi: 398297088 512-byte hdwr sectors (203928 MB)
> SCSI device sdi: drive cache: write back
> sdi: sdi1
> Attached scsi disk sdi at scsi9, channel 0, id 0, lun 0
> md: raid1 personality registered as nr 3
> md: Autodetecting RAID arrays.
> md: autorun ...
> ------
>
> lspci -v
> 00:00.0 Host bridge: VIA Technologies, Inc.: Unknown device 0258
>        Subsystem: ASRock Incorporation: Unknown device 0258
>        Flags: bus master, 66Mhz, medium devsel, latency 8
>        Memory at f8000000 (32-bit, prefetchable) [size=64M]
>        Capabilities: [80] AGP version 3.5
>        Capabilities: [50] Power Management version 2
>
> 00:00.1 Host bridge: VIA Technologies, Inc. PT880 Host Bridge
>        Subsystem: ASRock Incorporation: Unknown device 1258
>        Flags: bus master, medium devsel, latency 0
>
> 00:00.2 Host bridge: VIA Technologies, Inc. PT880 Host Bridge
>        Subsystem: ASRock Incorporation: Unknown device 2258
>        Flags: bus master, medium devsel, latency 0
>
> 00:00.3 Host bridge: VIA Technologies, Inc. PT880 Host Bridge
>        Subsystem: ASRock Incorporation: Unknown device 3258
>        Flags: bus master, medium devsel, latency 0
>
> 00:00.4 Host bridge: VIA Technologies, Inc. PT880 Host Bridge
>        Subsystem: ASRock Incorporation: Unknown device 4258
>        Flags: bus master, medium devsel, latency 0
>
> 00:00.7 Host bridge: VIA Technologies, Inc. PT880 Host Bridge
>        Subsystem: ASRock Incorporation: Unknown device 7258
>        Flags: bus master, medium devsel, latency 0
>
> 00:01.0 PCI bridge: VIA Technologies, Inc. VT8237 PCI Bridge (prog-if 00 
> [Normal decode])
>        Flags: bus master, 66Mhz, medium devsel, latency 0
>        Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
>        Memory behind bridge: fc600000-fe6fffff
>        Prefetchable memory behind bridge: f3f00000-f7efffff
>        Capabilities: [70] Power Management version 2
>
> 00:0b.0 RAID bus controller: Promise Technology, Inc. PDC20621 [SATA150 
> SX4] 4 Channel IDE RAID Controller (rev 01)
>        Subsystem: Promise Technology, Inc. PDC20621 [SATA150 SX4] 4 
> Channel IDE RAID Controller
>        Flags: bus master, 66Mhz, medium devsel, latency 96, IRQ 5
>        I/O ports at b000 [size=256]
>        I/O ports at a800 [size=256]
>        I/O ports at a400 [size=256]
>        Memory at fe900000 (32-bit, non-prefetchable) [size=1M]
>        Memory at febd8000 (32-bit, non-prefetchable) [size=32K]
>        Expansion ROM at febc0000 [disabled] [size=64K]
>        Capabilities: [60] Power Management version 1
>
> 00:0d.0 RAID bus controller: Promise Technology, Inc. PDC20621 [SATA150 
> SX4] 4 Channel IDE RAID Controller (rev 01)
>        Subsystem: Promise Technology, Inc. PDC20621 [SATA150 SX4] 4 
> Channel IDE RAID Controller
>        Flags: bus master, 66Mhz, medium devsel, latency 96, IRQ 10
>        I/O ports at c000 [size=256]
>        I/O ports at b800 [size=256]
>        I/O ports at b400 [size=256]
>        Memory at fea00000 (32-bit, non-prefetchable) [size=1M]
>        Memory at febf0000 (32-bit, non-prefetchable) [size=32K]
>        Expansion ROM at febe0000 [disabled] [size=64K]
>        Capabilities: [60] Power Management version 1
>
> 00:0f.0 RAID bus controller: VIA Technologies, Inc. VIA VT6420 SATA RAID 
> Controller (rev 80)
>        Subsystem: ASRock Incorporation: Unknown device 3149
>        Flags: bus master, medium devsel, latency 32, IRQ 10
>        I/O ports at ec00 [size=8]
>        I/O ports at e800 [size=4]
>        I/O ports at e400 [size=8]
>        I/O ports at e000 [size=4]
>        I/O ports at dc00 [size=16]
>        I/O ports at d800 [size=256]
>        Capabilities: [c0] Power Management version 2
>
> 00:0f.1 IDE interface: VIA Technologies, Inc. 
> VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) (prog-if 
> 8a [Master SecP PriP])
>        Subsystem: ASRock Incorporation K7VT2 motherboard
>        Flags: bus master, medium devsel, latency 32
>        I/O ports at fc00 [size=16]
>        Capabilities: [c0] Power Management version 2
>
> 00:11.0 ISA bridge: VIA Technologies, Inc. VT8237 ISA bridge 
> [KT600/K8T800/K8T890 South]
>        Subsystem: ASRock Incorporation: Unknown device 3227
>        Flags: bus master, stepping, medium devsel, latency 0
>        Capabilities: [c0] Power Management version 2
>
> 00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev 
> 78)
>        Subsystem: ASRock Incorporation: Unknown device 3065
>        Flags: bus master, medium devsel, latency 32, IRQ 11
>        I/O ports at d400 [size=256]
>        Memory at febffc00 (32-bit, non-prefetchable) [size=256]
>        Capabilities: [40] Power Management version 2
>
> 01:00.0 VGA compatible controller: nVidia Corporation NV5M64 [RIVA TNT2 
> Model 64/Model 64 Pro] (rev 15) (prog-if 00 [VGA])
>        Subsystem: PROLINK Microsystems Corp Pixelview RIVA TNT2 M64
>        Flags: bus master, 66Mhz, medium devsel, latency 32, IRQ 11
>        Memory at fd000000 (32-bit, non-prefetchable) [size=16M]
>        Memory at f4000000 (32-bit, prefetchable) [size=32M]
>        Expansion ROM at fe6f0000 [disabled] [size=64K]
>        Capabilities: [60] Power Management version 1
>        Capabilities: [44] AGP version 2.0
>
>
>
>
>
>
> cat /proc/interrupts
>           CPU0
>  0:     217348          XT-PIC  timer
>  1:         44          XT-PIC  i8042
>  2:          0          XT-PIC  cascade
>  4:         12          XT-PIC  serial
>  5:        135          XT-PIC  libata
>  8:          1          XT-PIC  rtc
> 10:        158          XT-PIC  libata, libata
> 11:        513          XT-PIC  eth0
> 12:        101          XT-PIC  i8042
> 14:       4612          XT-PIC  ide0
> 15:       5431          XT-PIC  ide1
> NMI:          0
> ERR:          0 




More information about the fedora-list mailing list