FC3, USB stick, and IBM t41 laptop oddities

[Petr Šimon]

Hi,
You might want to try to load usbcore with old_scheme_first=y or 
use_both_schemes=y option. See if it helps.
Good luck
Petr

Harry Hoffman wrote:

> Hi Pete,
>
> Sorry things have been kinda busy at work so I haven't had much time 
> to test.
> In short it still doesn't work. Details are listed below.
> Thanks again for following up!
>
> Running kernel: 2.6.10-1.741_FC3
>
> modprobe.conf:
> alias usb-controller ehci-hcd
> alias usb-controller1 uhci-hcd
>
>
> Insert the SanDisk Cruzer 1GB drive and get the following in 
> /var/log/messages:
> Feb  1 10:16:23 n1-22-129 kernel: usb 1-4: new high speed USB device 
> using ehci_hcd and address 10
> Feb  1 10:16:23 n1-22-129 kernel: ehci_hcd 0000:00:1d.7: port 4 reset 
> error -110Feb  1 10:16:23 n1-22-129 kernel: hub 1-0:1.0: 
> hub_port_status failed (err = -32)
> Feb  1 10:16:24 n1-22-129 kernel: usb 1-4: new high speed USB device 
> using ehci_hcd and address 12
> Feb  1 10:16:24 n1-22-129 kernel: ehci_hcd 0000:00:1d.7: port 4 reset 
> error -110Feb  1 10:16:24 n1-22-129 kernel: hub 1-0:1.0: 
> hub_port_status failed (err = -32)
> Feb  1 10:16:25 n1-22-129 kernel: usb 1-4: device descriptor read/64, 
> error -71
> ...
> Feb  1 10:16:27 n1-22-129 kernel: ehci_hcd 0000:00:1d.7: port 4 reset 
> error -110Feb  1 10:16:27 n1-22-129 kernel: hub 1-0:1.0: 
> hub_port_status failed (err = -32)
> Feb  1 10:16:28 n1-22-129 kernel: usb 1-4: new high speed USB device 
> using ehci_hcd and address 19
> ...
> Feb  1 10:16:30 n1-22-129 kernel: ehci_hcd 0000:00:1d.7: port 4 reset 
> error -110Feb  1 10:16:30 n1-22-129 kernel: hub 1-0:1.0: 
> hub_port_status failed (err = -32)
> Feb  1 10:16:30 n1-22-129 kernel: usb 1-4: device descriptor read/64, 
> error -71
> Feb  1 10:16:30 n1-22-129 kernel: usb 1-4: device descriptor read/64, 
> error -71
>
> If you need I can test other USB2.0 devices later this week.
>
> Cheers,
> Harry
>
>
> Pete Zaitcev wrote:
>
>> On Sun, 09 Jan 2005 22:53:33 -0500, Harry Hoffman 
>> <hhoffman at ip-solutions.net> wrote:
>>
>>
>>> It's 2.6.9-1.724_FC3
>>>
>>> I'm guessing it's a problem with ehci as well as none of my USB2.0 
>>> devices seem to work with ehci loaded :-(
>>
>>
>>
>> Hello, Harry:
>>
>> What is the situation now with 2.6.10 stream (2.6.10-1.741_FC3)?
>>
>> -- Pete
>
>