Sound card not working in Fedora Core 3

Kunal Shah kunalv.shah at gmail.com
Thu Feb 10 00:44:46 UTC 2005 

Thanks all for replying.

I will check the ALSA. Meanwhile here is the output from my lspci
command. Attached as txt file.
 



On Tue, 2005-02-08 at 19:55 -0600, Gain Paolo Mureddu wrote:
> Kunal Shah wrote:
> 
> >I know this problem has been discussed n number of times here. I have
> >been googling for this but could not find proper resolution.
> >
> >It seems that i have two problems and solving them can cause other
> >problems as i have see earlier too.
> >
> >Prob 1. 
> >I am using Gateway 4535Gz laptop and in the configuration document it
> >shows that i have
> >Analog Devices SoundMAX Integrated Digital Audio
> >
> >(I have downloaded chip identification util from intel site and i can
> >give you exact chip number for the same if you need to assist me.)
> >
> >but in linux when i do sound configuration from GNOME it detects that i
> >have intel ac97. I dont know how they are related.
> >
> >Prob 2. If the sound card detected by linux is accurate, still i dont
> >have sound. I have gone through each and every documentation in alsa
> >proj site and double checked all the mixer settings that nothing is
> >mute.
> >
> >If i try to install new alsa driver ( alsa-driver rpm is not installed
> >in fedora and its not available on fedora site. Only alsa packages
> >installed on my system are alsa-lib and alsa-devel). it screws up the
> >module information and next time when i do modprobe snd_intel8x0, it
> >gives me tons of errors.
> >
> >Please let me know if any one can help me in what is going on.
> >
> >
> >
> >Addition information about system
> >
> >[kunalshah at laptop ~]$ rpm -qa | grep alsa
> >alsa-utils-1.0.6-3
> >alsa-lib-1.0.6-7.FC3
> >alsa-lib-devel-1.0.6-7.FC3
> >[kunalshah at laptop ~]$ uname -r
> >2.6.10-1.760_FC3
> >[kunalshah at laptop ~]$ cat /etc/redhat-release
> >Fedora Core release 3 (Heidelberg)
> >[kunalshah at laptop ~]$ sudo su -
> >[root at laptop ~]# modinfo soundcore
> >filename:       /lib/modules/2.6.10-1.760_FC3/kernel/sound/soundcore.ko
> >description:    Core sound module
> >author:         Alan Cox
> >license:        GPL
> >alias:          char-major-14-*
> >vermagic:       2.6.10-1.760_FC3 686 REGPARM 4KSTACKS gcc-3.4
> >depends:
> >srcversion:     4CCBC38AF44D1461882C573
> >
> >
> >
> >Thanks
> >Kunal
> >
> >
> >  
> >
> Ok, Fedora uses the drivers provided by the version of ALSA merged into 
> the kernel, at this point only ALSA 1.0.6 has been merged into 
> kernel-code. This is an outdated version of ALSA, the current version is 
> 1.0.8. That is why you don't see an ALSA-kernel-module package in the 
> fedora downlaods, becuase it is already into the kernel package. Only 
> -utils and -lib are really necesary as separate packages... I'd really 
> recommend you checking for an updated version of ALSA and if you can, 
> search the archives of the alsa-user mailing list, there are some nice 
> tips in there for these sound cards (plus the installation instructions 
> at the alsa-prject site).
> 
-------------- next part --------------
00:00.0 Host bridge: Intel Corp. 82852/82855 GM/GME/PM/GMV Processor to I/O Controller (rev 02)
	Subsystem: Rioworks: Unknown device 203a
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
	Latency: 0
	Region 0: Memory at <unassigned> (32-bit, prefetchable)
	Capabilities: [40] Vendor Specific Information

00:00.1 System peripheral: Intel Corp. 82852/82855 GM/GME/PM/GMV Processor to I/O Controller (rev 02)
	Subsystem: Rioworks: Unknown device 203a
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0

00:00.3 System peripheral: Intel Corp. 82852/82855 GM/GME/PM/GMV Processor to I/O Controller (rev 02)
	Subsystem: Rioworks: Unknown device 203a
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0

00:02.0 VGA compatible controller: Intel Corp. 82852/855GM Integrated Graphics Device (rev 02) (prog-if 00 [VGA])
	Subsystem: Rioworks: Unknown device 203a
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0
	Interrupt: pin A routed to IRQ 5
	Region 0: Memory at e8000000 (32-bit, prefetchable) [size=128M]
	Region 1: Memory at e0000000 (32-bit, non-prefetchable) [size=512K]
	Region 2: I/O ports at 1800 [size=8]
	Capabilities: [d0] Power Management version 1
		Flags: PMEClk- DSI+ D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:02.1 Display controller: Intel Corp. 82852/855GM Integrated Graphics Device (rev 02)
	Subsystem: Rioworks: Unknown device 203a
	Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Region 0: Memory at f0000000 (32-bit, prefetchable) [size=128M]
	Region 1: Memory at e0080000 (32-bit, non-prefetchable) [size=512K]
	Capabilities: [d0] Power Management version 1
		Flags: PMEClk- DSI+ D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:1d.0 USB Controller: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #1 (rev 03) (prog-if 00 [UHCI])
	Subsystem: Rioworks: Unknown device 203a
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0
	Interrupt: pin A routed to IRQ 5
	Region 4: I/O ports at 1820 [size=32]

00:1d.1 USB Controller: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #2 (rev 03) (prog-if 00 [UHCI])
	Subsystem: Rioworks: Unknown device 203a
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0
	Interrupt: pin B routed to IRQ 11
	Region 4: I/O ports at 1840 [size=32]

00:1d.2 USB Controller: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #3 (rev 03) (prog-if 00 [UHCI])
	Subsystem: Rioworks: Unknown device 203a
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0
	Interrupt: pin C routed to IRQ 10
	Region 4: I/O ports at 1860 [size=32]

00:1d.7 USB Controller: Intel Corp. 82801DB/DBM (ICH4/ICH4-M) USB2 EHCI Controller (rev 03) (prog-if 20 [EHCI])
	Subsystem: Rioworks: Unknown device 203a
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0
	Interrupt: pin D routed to IRQ 3
	Region 0: Memory at e0100000 (32-bit, non-prefetchable) [size=1K]
	Capabilities: [50] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [58] Debug port

00:1e.0 PCI bridge: Intel Corp. 82801 Mobile PCI Bridge (rev 83) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR+
	Latency: 0
	Bus: primary=00, secondary=02, subordinate=02, sec-latency=32
	I/O behind bridge: 00003000-00003fff
	Memory behind bridge: e0200000-e02fffff
	Secondary status: 66Mhz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-

00:1f.0 ISA bridge: Intel Corp. 82801DBM (ICH4-M) LPC Interface Bridge (rev 03)
	Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0

00:1f.1 IDE interface: Intel Corp. 82801DBM (ICH4-M) IDE Controller (rev 03) (prog-if 8a [Master SecP PriP])
	Subsystem: Rioworks: Unknown device 203a
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0
	Interrupt: pin A routed to IRQ 10
	Region 0: I/O ports at <unassigned>
	Region 1: I/O ports at <unassigned>
	Region 2: I/O ports at <unassigned>
	Region 3: I/O ports at <unassigned>
	Region 4: I/O ports at 1810 [size=16]
	Region 5: Memory at 20000000 (32-bit, non-prefetchable) [size=1K]

00:1f.3 SMBus: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) SMBus Controller (rev 03)
	Subsystem: Rioworks: Unknown device 203a
	Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Interrupt: pin B routed to IRQ 10
	Region 4: I/O ports at 1880 [size=32]

00:1f.5 Multimedia audio controller: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Audio Controller (rev 03)
	Subsystem: Rioworks: Unknown device 203a
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0
	Interrupt: pin B routed to IRQ 10
	Region 0: I/O ports at 1c00 [size=256]
	Region 1: I/O ports at 18c0 [size=64]
	Region 2: Memory at e0100c00 (32-bit, non-prefetchable) [size=512]
	Region 3: Memory at e0100800 (32-bit, non-prefetchable) [size=256]
	Capabilities: [50] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:1f.6 Modem: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Modem Controller (rev 03) (prog-if 00 [Generic])
	Subsystem: Rioworks: Unknown device 2030
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0
	Interrupt: pin B routed to IRQ 10
	Region 0: I/O ports at 2400 [size=256]
	Region 1: I/O ports at 2000 [size=128]
	Capabilities: [50] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

02:07.0 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev a9)
	Subsystem: Rioworks: Unknown device 203a
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 168
	Interrupt: pin A routed to IRQ 11
	Region 0: Memory at 20001000 (32-bit, non-prefetchable) [size=4K]
	Bus: primary=02, secondary=03, subordinate=06, sec-latency=176
	Memory window 0: 20400000-207ff000 (prefetchable)
	Memory window 1: 20800000-20bff000
	I/O window 0: 00004000-000040ff
	I/O window 1: 00004400-000044ff
	BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
	16-bit legacy interface ports at 0001

02:07.1 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev a9)
	Subsystem: Rioworks: Unknown device 203a
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 168
	Interrupt: pin B routed to IRQ 10
	Region 0: Memory at 20002000 (32-bit, non-prefetchable) [size=4K]
	Bus: primary=02, secondary=07, subordinate=0a, sec-latency=176
	Memory window 0: 20c00000-20fff000 (prefetchable)
	Memory window 1: 21000000-213ff000
	I/O window 0: 00004800-000048ff
	I/O window 1: 00004c00-00004cff
	BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
	16-bit legacy interface ports at 0001

02:07.2 FireWire (IEEE 1394): Ricoh Co Ltd R5C552 IEEE 1394 Controller (rev 01) (prog-if 10 [OHCI])
	Subsystem: Rioworks: Unknown device 203a
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32 (500ns min, 1000ns max)
	Interrupt: pin C routed to IRQ 10
	Region 0: Memory at e0201000 (32-bit, non-prefetchable) [size=2K]
	Capabilities: [dc] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=2 PME+

02:08.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
	Subsystem: Rioworks: Unknown device 202d
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32 (8000ns min, 16000ns max)
	Interrupt: pin A routed to IRQ 10
	Region 0: I/O ports at 3000 [size=256]
	Region 1: Memory at e0201800 (32-bit, non-prefetchable) [size=256]
	Capabilities: [50] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

02:09.0 Network controller: Intel Corp. PRO/Wireless 2200BG (rev 05)
	Subsystem: Intel Corp.: Unknown device 2701
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32 (750ns min, 6000ns max), Cache Line Size 10
	Interrupt: pin A routed to IRQ 10
	Region 0: Memory at e0200000 (32-bit, non-prefetchable) [size=4K]
	Capabilities: [dc] Power Management version 2
		Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=1 PME-

More information about the fedora-list mailing list