(part 2) wifi and fedora core 3
Mike Hoy
mhoy4 at cox.net
Fri Jan 21 16:05:54 UTC 2005
part 2
Up til now I haven't had any luck with iwconfig or Kwifimanager
but I came across info on the web it said to do this:
# /sbin/lsmod | grep "orinoco"
and if there is nothing outputted then i have to load my drivers myself
so I:
# /sbin/modprobe orinoco
# /sbin/modprobe orinoco_cs
now the Kwifimanager at least shows connected but oddly enough no ip!
here is the output of iwconfig:
eth1 IEEE 802.11-DS ESSID:"WillowHouse" Nickname:"Prism I"
Mode:Managed Frequency:2.437GHz Access Point:
00:0F:66:20:8F:93 Bit Rate:11Mb/s Tx-Power=15 dBm
Sensitivity:1/3 Retry min limit:8 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality=78/92 Signal level=-18 dBm Noise level=-145 dBm
Rx invalid nwid:0 Rx invalid crypt:211 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
yes the willow house is my ap :-)
just for the heck of it here's ifconfig:
eth1 Link encap:Ethernet HWaddr 00:09:5B:23:3B:D6 inet6
addr: fe80::209:5bff:fe23:3bd6/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:48 errors:0 dropped:0 overruns:0 frame:0
TX packets:3 errors:2 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:5183 (5.0 KiB) TX bytes:372 (372.0 b)
Interrupt:3 Base address:0x100
ok, now that to me is odd. in ifconfig it says inet6.
then i dmesg and thot this was weird:
[drm] Loading R200 Microcode
eth1: Error -110 setting multicast list.
eth1: Error -110 setting multicast list.
eth1: Error -110 setting multicast list.
eth1: New link status: Connected (0001)
eth1: no IPv6 routers present
irq 5: nobody cared (try booting with the "irqpoll" option.
[<c013c2c8>] __report_bad_irq+0x2b/0x68
[<c013c391>] note_interrupt+0x73/0x96
[<c013b996>] __do_IRQ+0x19f/0x221
[<c0104ca8>] do_IRQ+0x5e/0x7a
=======================
[<c01034da>] common_interrupt+0x1a/0x20
[<c01203e8>] __do_softirq+0x2c/0x79
[<c0104d80>] do_softirq+0x38/0x3f
=======================
[<c0104cba>] do_IRQ+0x70/0x7a
[<c01034da>] common_interrupt+0x1a/0x20
[<c020493a>] acpi_processor_idle+0xf1/0x1f6
[<c010108f>] cpu_idle+0x1f/0x34
[<c039c665>] start_kernel+0x16b/0x16d
handlers:
[<c0275b81>] (usb_hcd_irq+0x0/0x4b)
Disabling IRQ #5
so is this an irq concflict
how can i "try booting with the "irqpoll" option" and should I?
my understanding of the problem is that I have great signal strength but
no ip addy and that it's configured as ipv6.
btw here is a very small pic of the kwifimgr to show it's info:
http://members.cox.net/mhoy4/kwifimgr.png
and just for the heck of it i connected in xp just to make sure their ap
was working and it was.
altho i did use a different wifi card in xp.
thanks in advance,
mike hoy
jim lawrence wrote:
>http://www.linuxquestions.org/hcl/showproduct.php?product=159
>
>let me know if you get this to work, my brother has one of these and
>is thinking of installing FC3
>
>
>On Thu, 20 Jan 2005 22:56:59 -0700, Mike Hoy <mhoy4 at cox.net> wrote:
>
>
>>hi,
>>
>>anyone here use FC3 and a netgear ma401 802.11b pcmcia wifi card?
>>
>>if so does it work? did it always work or did you have to do something
>>to get it to work?
>>
>>mike h
>>
>>--
>>fedora-list mailing list
>>fedora-list at redhat.com
>>To unsubscribe: http://www.redhat.com/mailman/listinfo/fedora-list
>>
>>
>>
>
>
>
>
More information about the fedora-list
mailing list