Is the HP PSC 1315 not recognized by FC4?

[Vinicius]

Vinicius escreveu:
> Vinicius escreveu:
> 
>> Jerry DeLisle escreveu:
>>
>>> Vinicius wrote:
>>>
>>>> Jerry DeLisle escreveu:
>>>>
>>>>> Vinicius wrote:
>>>>>
>>>>>> Hello,
>>>>>>
>>>>>> I have a HP PSC 1315 and the computer OS is FC4 (the kernel is 
>>>>>> 2.6.12-1.1387_FC4).
>>>>>>
>>>>>> The command lspci is not showing the printer, but it did show on 
>>>>>> FC3 and the printer was working on FC3.
>>>>>>
>>>>>> Any ideias, please?
>>>>>>
>>>>>>
>>>>>> TIA,
>>>>>>
>>>>>> Vinicius.
>>>>>>
>>>>> Go to this site.
>>>>>
>>>>> http://hpinkjet.sourceforge.net/
>>>>>
>>>>> There are details for installation.  I have hplip running on FC4 
>>>>> like a charm.  Puts an icon in the accessories menu.  Click on that 
>>>>> and you have full control.
>>>>>
>>>>> Jerry
>>>>>
>>>>
>>>> Thanks.
>>>>
>>>> Is your SELinux active ("enforcing" and "targeted")?
>>>>
>>>> I have used hplip since 0.8X to 0.9.2 without problem on FC3.
>>>> I have compiled and installed it (version 0.9.3) on FC4, but there 
>>>> are several "avc denied" due to SELinux.
>>>> Unfortunately, I think it's a hardware or configuration issue. I 
>>>> don't know if it is due kudzu or the kernel, or other component.
>>>> As I said, the command *lspci* is not showing the printer, 
>>>> independent of hplip installation or not.
>>>>
>>>>
>>>> Vinicius.
>>>>
>>> I do have SELinux enabled and have a few "avc denied" messages but 
>>> all is working.  I have a PSC 2175 plugged into USB port.  It shows 
>>> up fine with lsusb. I do not know the kind of interface for PSC 
>>> 1315.  I would try the hplip mailing list and see if they have any 
>>> ideas.
>>>
>>> Jerry
>>>
>>
>> Thanks again.
>>
>> I'm participating of the HPLIP forums but without success to solve the 
>> problem there.
>>
>> I have reinstalled the FC4 from the zero and the problem continues.
>>
>> Have you installed the FC4 from the zero or upgraded from another 
>> version of Fedora, please?
>>
>> My PSC 1315 uses USB to communicate with the computer.
>>
>> What's the outputs of the commands lsusb and lspci, please?
>>
>>
>> TIA,
>>
>> Vinicius.
>>
> 
> Before the tip:
> "
> # lsusb
> Bus 005 Device 001: ID 0000:0000
> Bus 004 Device 001: ID 0000:0000
> Bus 003 Device 001: ID 0000:0000
> Bus 002 Device 001: ID 0000:0000
> Bus 001 Device 001: ID 0000:0000
> "
> 
> After the tip from Kam Leo:
> "
> Bus 005 Device 001: ID 0000:0000
> *Bus 004 Device 002: ID 03f0:3f11 Hewlett-Packard PSC-1315*
> Bus 004 Device 001: ID 0000:0000
> Bus 003 Device 001: ID 0000:0000
> Bus 002 Device 001: ID 0000:0000
> Bus 001 Device 001: ID 0000:0000
> "
> 
> Now I can install the HPLIP driver.
> 
> 
> Thanks,
> 
> Vinicius.
> 

Hello,

there is something strange, because each restart of the computer, lsusb 
is not showing the printer, I can see the printer information after I 
turn off and then turn on the printer.

Vinicius.