pilot-link issues

[lance raymond]

sorry, didn't 4get to run it, just mention it ... sorry.

Not sure what that command is, but an ls-l shows it as:

crw-r--r--  1 lance root 188, 1 Nov  7 16:28 /tmp/pilot

thanks.

lr

On Mon, 2005-11-07 at 15:03 -0700, Craig White wrote:

> On Mon, 2005-11-07 at 16:53 -0500, lance raymond wrote:
> > Only caught the tail end of Craigs post, so this might be a similar
> > post, so I did look at the tests with the same results.  Here are my
> > details, so any help is appreciated.
> > 
> > I am trying to sync  Treo 600, there is an entry in the devices.xml
> > for it:
> > <!-- Handspring Treo 600 -->
> > <device vendor_id="082d" product_id="0300" />
> > 
> > I also have the following RPM's installed:
> > gnome-pilot-2.0.13-2
> > gnome-pilot-devel-2.0.13-2
> > gnome-pilot-conduits-2.0.13-1
> > pilot-link-debuginfo-0.12.0-0.pre4.0.fc4.2
> > pilot-link-devel-0.12.0-0.pre4.0.fc4.2
> > pilot-link-0.12.0-0.pre4.0.fc4.2
> > jpilot-0.99.8-0.pre10.fc4.1
> > jpilot-debuginfo-0.99.8-0.pre10.fc4.1
> > 
> > Once I plug in the device (not hitting the sync I get the following:
> > Nov  7 16:24:15 vader kernel: usb 2-1: new full speed USB device using
> > uhci_hcd and address 6
> > Nov  7 16:24:15 vader kernel: visor 2-1:1.0: Handspring Visor / Palm
> > OS converter detected
> > Nov  7 16:24:15 vader kernel: usb 2-1: Handspring Visor / Palm OS
> > converter now attached to ttyUSB2
> > Nov  7 16:24:15 vader kernel: usb 2-1: Handspring Visor / Palm OS
> > converter now attached to ttyUSB3
> > Nov  7 16:24:38 vader kernel: usb 2-1: USB disconnect, address 6
> > 
> > I did issue the commands in the previous thread, pilot-xfer -L -
> > p /tmp/pilot it  sits and waits for connection, even after pressing
> > the hot-sync button there is nothing. Once disconnected you recieve
> > Nov  7 16:26:04 vader kernel: visor ttyUSB0: Handspring Visor / Palm
> > OS converter now disconnected from ttyUSB0
> > Nov  7 16:26:05 vader kernel: visor ttyUSB1: Handspring Visor / Palm
> > OS converter now disconnected from ttyUSB1
> > 
> > I would like to sync w/ evolution, if it must be a jpilot type app, so
> > be it, but any help to get this going is appreciated.
> > 
> ----
> re-read my post as evidently you missed the all important step of mknod
> 
> unless you do that, you won't get it to work with pilot-xfer and once
> you get it to work with pilot xfer, you should be able to figure out
> what change you need to make to get it to work with gpilotd (evolution)
> 
> Craig
> 
> 
> -- 
> This message has been scanned for viruses and
> dangerous content by MailScanner, and is
> believed to be clean.
> 

-- 
    .~.
    /V\
   // \\
  /(   )\
   ^`~'^   
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://listman.redhat.com/archives/fedora-list/attachments/20051107/a96d4e75/attachment-0001.htm>