How to make hotplug work
Bob Chiodini
rchiodin at bellsouth.net
Wed Oct 5 13:46:46 UTC 2005
On Tue, 2005-10-04 at 12:38 -0400, Gavin Li wrote:
> > Gavin,
> >
> > I think echo /sbin/udevsend > /proc/sys/kernel/hotplug should be
> > echo /sbin/hotplug > /proc/sys/kernel/hotplug, if it is not already. I,
>
> I already tried both of them, it just doesn't log anything.
>
> > also had to modprobe usbcore as part of system initialization. I was
>
> I use RHFC3 kernel binary. I checked rc.sysinit in RHFC3, it loads all the
> modules, does it need to be done? I think the hotplug should do it when
> neccessary. I found it by call "exit 0" before it prints "Init hardware" and
> after it. The hotplug starts working after Init hardware ( which all the
> modules have been loaded ), don't understand.
> and Then I tried to modprobe usb-storage, and sd_mod module, and then try
> hotplug, it doesn't work.
>
>
> > working with a 2.4.x kernel. There is a typo near the end of rcS the
>
> I don't have problem with 2.4.x kernel
>
> > moun should be mount. Cut and paste problem?
>
> I typed in, so it is a typo.
>
> >
> > Bob...
> >
> > This is the /sbin/hotplug that I came up with. Rather "brute force",
> > but it only needed to do one thing, mount a USB stick.
>
>
Gavin,
Some questions:
Does anything show up in dmesg or /var/log/messages when you plug in
your device?
Are the modules usbcore, uhci, and/or ehci loaded before you plug in
your device. I would think you would at least need uhci/ehci, or they
are compiled into the kernel. There also may be some dependency on
hald. I plugged a USB stick into my FC3 box and got the following
in /var/log/messages:
Oct 5 09:31:00 tweedy kernel: usb 1-8.4: new full speed USB device
using ehci_hcd and address 6
Oct 5 09:31:01 tweedy kernel: Initializing USB Mass Storage driver...
Oct 5 09:31:01 tweedy kernel: scsi2 : SCSI emulation for USB Mass
Storage devices
Oct 5 09:31:01 tweedy kernel: usbcore: registered new driver usb-
storage
Oct 5 09:31:01 tweedy kernel: USB Mass Storage support registered.
Oct 5 09:31:06 tweedy kernel: Vendor: LEXAR Model: DIGITAL FILM
Rev: /W1.
Oct 5 09:31:06 tweedy kernel: Type: Direct-Access
ANSI SCSI revision: 02
Oct 5 09:31:06 tweedy scsi.agent[25481]: disk
at /devices/pci0000:00/0000:00:1d.7/usb1/1-8/1-8.4/1-8.4:1.0/host2/target2:0:0/2:0:0:0
Oct 5 09:31:06 tweedy kernel: SCSI device sda: 251904 512-byte hdwr
sectors (129 MB)
Oct 5 09:31:06 tweedy kernel: sda: Write Protect is off
Oct 5 09:31:06 tweedy kernel: sda: assuming drive cache: write through
Oct 5 09:31:06 tweedy kernel: SCSI device sda: 251904 512-byte hdwr
sectors (129 MB)
Oct 5 09:31:06 tweedy kernel: sda: Write Protect is off
Oct 5 09:31:06 tweedy kernel: sda: assuming drive cache: write through
Oct 5 09:31:06 tweedy kernel: sda: sda1
Oct 5 09:31:06 tweedy kernel: Attached scsi removable disk sda at
scsi2, channel 0, id 0, lun 0
Oct 5 09:31:07 tweedy fstab-sync[25548]: added mount
point /media/USB_MEMORY for /dev/sda1
Oct 5 09:31:07 tweedy kernel: FAT: utf8 is not a recommended IO charset
for FAT filesystems, filesystem will be case sensitive!
Oct 5 09:31:07 tweedy kernel: SELinux: initialized (dev sda1, type
vfat), uses genfs_contexts
Oct 5 09:31:50 tweedy kernel: usb 1-8.4: USB disconnect, address 6
Oct 5 09:31:50 tweedy fstab-sync[25671]: removed mount
point /media/USB_MEMORY for /dev/sda1
Possibly ehci_hcd is also needed. The following modules were loaded in
response to inserting the stick:
nls_utf8 6081 0
vfat 17217 0
fat 55005 1 vfat
sd_mod 22721 0
usb_storage 73993 0
USB and the 2.6 kernel seem more complex than the 2.4 kernel.
Hopefully someone else can enlighten us.
BTW: All of the above is from FC3 (kernel 2.6.12-1.1378_FC3smp),
and /proc/sys/kernel/hotplug is
[bob at tweedy kernel]$ cat hotplug
/sbin/hotplug
[bob at tweedy kernel]$ file /sbin/hotplug
/sbin/hotplug: Bourne shell script text executable
Bob...
More information about the fedora-list
mailing list