kdump on Fedora 7
Igor A. Nesterov
igor.nesterov at indexengines.com
Tue Oct 2 22:47:38 UTC 2007
Hi,
I am trying to make working kdump on Fedora 7. The system is
Linux don2 2.6.22.5-76.fc7 #1 SMP Thu Aug 30 13:08:59 EDT 2007 x86_64
x86_64 x86_64 GNU/Linux
with
kexec-tools-1.101-71.fc7
I honestly follow instructions from howto provided with kexec-tools
package
/usr/share/doc/kexec-tools-1.101/kexec-kdump-howto.txt
Everything works well, kexec -l works fine and kdump service starts
fine, except that when I do force-crash to test it, then after the
system is rebooted there is not any memory dump in /var/crash. Attached
is a kernel log acquired with a serial cable starting from SysRq trigger
and up to the successful restart of the original kernel. From what I can
see in this log crash kernel boots and goes up to the point, where the
normal kernel starts initrd execution. But right after that instead of
starting kdump initrd crash kernel suddenly does the cold reboot and the
normal system start happens. What's wrong with my setup? Has anybody
run/tested this functionality in Fedora 7?
-------------- next part --------------
SysRq : Trigger a crashdump
Linux version 2.6.22.5-76.fc7 (kojibuilder at xenbuilder4.fedora.phx.redhat.com) (gcc version 4.1.2 20070502 (Red Hat 4.1.2-12)) #1 SMP Thu Aug 30 13:08:59 EDT 2007
Command line: ro root=/dev/VolGroup00/LogVol00 rhgb ignore_loglevel console=ttyS0,57600n8 irqpoll maxcpus=1 memmap=exactmap memmap=640K at 0K memmap=261488K at 17024K elfcorehdr=278512K memmap=56K#1048320K memmap=136K#1048376K
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000100 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e8000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003ffc0000 (usable)
BIOS-e820: 000000003ffc0000 - 000000003ffce000 (ACPI data)
BIOS-e820: 000000003ffce000 - 000000003fff0000 (ACPI NVS)
BIOS-e820: 000000003fff0000 - 0000000040000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000ff700000 - 0000000100000000 (reserved)
Entering add_active_range(0, 1, 159) 0 entries of 3200 used
Entering add_active_range(0, 256, 262080) 1 entries of 3200 used
end_pfn_map = 1048576
user-defined physical RAM map:
user: 0000000000000000 - 00000000000a0000 (usable)
user: 00000000010a0000 - 0000000010ffc000 (usable)
user: 000000003ffc0000 - 000000003ffce000 (ACPI data)
user: 000000003ffce000 - 000000003fff0000 (ACPI data)
Entering add_active_range(0, 0, 160) 0 entries of 3200 used
Entering add_active_range(0, 4256, 69628) 1 entries of 3200 used
end_pfn_map = 262128
DMI 2.3 present.
ACPI: RSDP 000FB6C0, 0024 (r2 ACPIAM)
ACPI: XSDT 3FFC0100, 0044 (r1 A M I OEMXSDT 1000606 MSFT 97)
ACPI: FACP 3FFC0290, 00F4 (r3 A M I OEMFACP 1000606 MSFT 97)
ACPI Warning (tbfadt-0442): Optional field "Gpe1Block" has zero address or length: 00000000000044A0/0 [20070126]
ACPI: DSDT 3FFC03F0, 449D (r1 S0024 S0024001 1 INTL 2002026)
ACPI: FACS 3FFCE000, 0040
ACPI: APIC 3FFC0390, 005C (r1 A M I OEMAPIC 1000606 MSFT 97)
ACPI: OEMB 3FFCE040, 0063 (r1 A M I AMI_OEM 1000606 MSFT 97)
ACPI: MCFG 3FFC4890, 003C (r1 A M I OEMMCFG 1000606 MSFT 97)
Scanning NUMA topology in Northbridge 24
No NUMA configuration found
Faking a node at 0000000000000000-0000000010ffc000
Entering add_active_range(0, 0, 160) 0 entries of 3200 used
Entering add_active_range(0, 4256, 69628) 1 entries of 3200 used
Bootmem setup node 0 0000000000000000-0000000010ffc000
Zone PFN ranges:
DMA 0 -> 4096
DMA32 4096 -> 1048576
Normal 1048576 -> 1048576
early_node_map[2] active PFN ranges
0: 0 -> 160
0: 4256 -> 69628
On node 0 totalpages: 65532
DMA zone: 56 pages used for memmap
DMA zone: 8 pages reserved
DMA zone: 96 pages, LIFO batch:0
DMA32 zone: 895 pages used for memmap
DMA32 zone: 64477 pages, LIFO batch:15
Normal zone: 0 pages used for memmap
Nvidia board detected. Ignoring ACPI timer override.
If you got timer trouble try acpi_use_timer_override
ACPI: PM-Timer IO Port: 0x4008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 (Bootup-CPU)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x81] disabled)
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: BIOS IRQ0 pin2 override ignored.
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ9 used by override.
Setting APIC routing to flat
Using ACPI (MADT) for SMP configuration information
swsusp: Registered nosave memory region: 00000000000a0000 - 00000000010a0000
Allocating PCI resources starting at 40000000 (gap: 3fff0000:c0010000)
SMP: Allowing 2 CPUs, 1 hotplug CPUs
PERCPU: Allocating 40968 bytes of per cpu data
Built 1 zonelists. Total pages: 64573
Kernel command line: ro root=/dev/VolGroup00/LogVol00 rhgb ignore_loglevel console=ttyS0,57600n8 irqpoll maxcpus=1 memmap=exactmap memmap=640K at 0K memmap=261488K at 17024K elfcorehdr=278512K memmap=56K#1048320K memmap=136K#1048376K
debug: ignoring loglevel setting.
Misrouted IRQ fixup and polling support enabled
This may significantly impact system performance
Initializing CPU#0
PID hash table entries: 1024 (order: 10, 8192 bytes)
Extended CMOS year: 2000
time.c: Detected 1000.000 MHz processor.
Console: colour VGA+ 80x25
Checking aperture...
CPU 0: aperture @ 280000000 size 32 MB
Aperture too small (32 MB)
No AGP bridge found
Memory: 248456k/278512k available (2366k kernel code, 13672k reserved, 1400k data, 312k init)
SLUB: Genslabs=23, HWalign=64, Order=0-1, MinObjects=4, CPUs=2, Nodes=1
Calibrating delay using timer specific routine.. 2053.01 BogoMIPS (lpj=1026509)
Security Framework v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Dentry cache hash table entries: 32768 (order: 6, 262144 bytes)
Inode-cache hash table entries: 16384 (order: 5, 131072 bytes)
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 0/0 -> Node 0
SMP alternatives: switching to UP code
ACPI: Core revision 20070126
Using local APIC timer interrupts.
result 12500019
Detected 12.500 MHz APIC timer.
Brought up 1 CPUs
sizeof(vma)=176 bytes
sizeof(page)=56 bytes
sizeof(inode)=560 bytes
sizeof(dentry)=208 bytes
sizeof(ext3inode)=760 bytes
sizeof(buffer_head)=104 bytes
sizeof(skbuff)=232 bytes
sizeof(task_struct)=2048 bytes
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: BIOS Bug: MCFG area at e0000000 is not E820-reserved
PCI: Not using MMCONFIG.
PCI: Using configuration type 1
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI: Transparent bridge - 0000:00:09.0
PCI: PXH quirk detected, disabling MSI for SHPC device
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P3._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4.P4P5._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P6._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 16 *17 18 19)
ACPI: PCI Interrupt Link [LNKB] (IRQs 16 17 *18 19)
ACPI: PCI Interrupt Link [LNKC] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LNKD] (IRQs 16 17 18 *19)
ACPI: PCI Interrupt Link [LNKE] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LUS0] (IRQs 20 21 *22)
ACPI: PCI Interrupt Link [LUS1] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [LUS2] (IRQs 20 *21 22)
ACPI: PCI Interrupt Link [LKLN] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [LAUI] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [LKMO] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [LKSM] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [LTID] (IRQs *20 21 22)
ACPI: PCI Interrupt Link [LTIE] (IRQs 20 21 *22)
ACPI: PCI Interrupt Link [LATA] (IRQs 20 21 22) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 16 devices
ACPI: ACPI bus type pnp unregistered
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
ACPI: RTC can wake from S4
Time: tsc clocksource has been installed.
pnp: 00:07: iomem range 0xffb80000-0xfffffffe has been reserved
pnp: 00:07: iomem range 0x0-0x0 could not be reserved
pnp: 00:07: iomem range 0x0-0x0 could not be reserved
pnp: 00:07: iomem range 0x0-0x0 could not be reserved
pnp: 00:08: iomem range 0xfec00000-0xfec00fff has been reserved
pnp: 00:08: iomem range 0xfee00000-0xfeefffff could not be reserved
pnp: 00:0c: ioport range 0x290-0x297 has been reserved
pnp: 00:0e: iomem range 0xe0000000-0xefffffff has been reserved
pnp: 00:0f: iomem range 0x0-0x9ffff could not be reserved
pnp: 00:0f: iomem range 0xc0000-0xdffff has been reserved
pnp: 00:0f: iomem range 0xe0000-0xfffff has been reserved
pnp: 00:0f: iomem range 0x100000-0x3fffffff could not be reserved
PCI: Bridge: 0000:00:09.0
IO window: e000-efff
MEM window: def00000-dfffffff
PREFETCH window: 50000000-500fffff
PCI: Bridge: 0000:00:0b.0
IO window: disabled.
MEM window: dee00000-deefffff
PREFETCH window: 40000000-400fffff
PCI: Bridge: 0000:00:0c.0
IO window: disabled.
MEM window: ded00000-dedfffff
PREFETCH window: disabled.
PCI: Bridge: 0000:02:00.0
IO window: d000-dfff
MEM window: dec00000-decfffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:0d.0
IO window: d000-dfff
MEM window: dec00000-decfffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:0e.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Setting latency timer of device 0000:00:09.0 to 64
PCI: Setting latency timer of device 0000:00:0b.0 to 64
PCI: Setting latency timer of device 0000:00:0c.0 to 64
PCI: Setting latency timer of device 0000:00:0d.0 to 64
PCI: Setting latency timer of device 0000:02:00.0 to 64
PCI: Setting latency timer of device 0000:00:0e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 2, 16384 bytes)
TCP established hash table entries: 8192 (order: 5, 196608 bytes)
TCP bind hash table entries: 8192 (order: 5, 131072 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 2882k freed
audit: initializing netlink socket (disabled)
audit(1191363831.202:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
ksign: Installing public key data
Loading keyring
- Added public key 4A67DBB026B0246B
- User ID: Red Hat, Inc. (Kernel Module GPG key)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: Found disabled HT MSI Mapping on 0000:00:0b.0
PCI: Found enabled HT MSI Mapping on 0000:00:00.0
PCI: Found disabled HT MSI Mapping on 0000:00:0c.0
PCI: Found enabled HT MSI Mapping on 0000:00:00.0
PCI: Found disabled HT MSI Mapping on 0000:00:0d.0
PCI: Found enabled HT MSI Mapping on 0000:00:00.0
PCI: Found disabled HT MSI Mapping on 0000:00:0e.0
PCI: Found enabled HT MSI Mapping on 0000:00:00.0
Boot video device is 0000:06:05.0
PCI: Setting latency timer of device 0000:00:0b.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0b.0:pcie00]
PCI: Setting latency timer of device 0000:00:0c.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0c.0:pcie00]
PCI: Setting latency timer of device 0000:00:0d.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0d.0:pcie00]
PCI: Setting latency timer of device 0000:00:0e.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0e.0:pcie00]
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI Exception (processor_core-0781): AE_NOT_FOUND, Processor Device is not present [20070126]
Generic RTC Driver v1.07
Non-volatile memory driver v1.2
Linux agpgart interface v0.102 (c) Dave Jones
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
?serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:0d: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 16384K size 4096 blocksize
input: Macintosh mouse button emulation as /class/input/input0
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f12:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input1
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
powernow-k8: Found 1 AMD Opteron(tm) Processor 144 processors (version 2.00.00)
powernow-k8: 0 : fid 0xa (1800 MHz), vid 0x6
powernow-k8: 1 : fid 0x2 (1000 MHz), vid 0x12
drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
Freeing unused kernel memory: 312k freed
Write protecting the kernel read-only data: 1060k
<...some garbage...>Linux version 2.6.22.5-76.fc7 (kojibuilder at xenbuilder4.fedora.phx.redhat.com) (gcc version 4.1.2 20070502 (Red Hat 4.1.2-12)) #1 SMP Thu Aug 30 13:08:59 EDT 2007
Command line: ro root=/dev/VolGroup00/LogVol00 rhgb ignore_loglevel console=ttyS0,57600n8 crashkernel=256M at 16M
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e8000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003ffc0000 (usable)
BIOS-e820: 000000003ffc0000 - 000000003ffce000 (ACPI data)
BIOS-e820: 000000003ffce000 - 000000003fff0000 (ACPI NVS)
BIOS-e820: 000000003fff0000 - 0000000040000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ff700000 - 0000000100000000 (reserved)
Entering add_active_range(0, 0, 159) 0 entries of 3200 used
Entering add_active_range(0, 256, 262080) 1 entries of 3200 used
end_pfn_map = 1048576
DMI 2.3 present.
ACPI: RSDP 000FB6C0, 0024 (r2 ACPIAM)
ACPI: XSDT 3FFC0100, 0044 (r1 A M I OEMXSDT 1000606 MSFT 97)
ACPI: FACP 3FFC0290, 00F4 (r3 A M I OEMFACP 1000606 MSFT 97)
ACPI Warning (tbfadt-0442): Optional field "Gpe1Block" has zero address or length: 00000000000044A0/0 [20070126]
ACPI: DSDT 3FFC03F0, 449D (r1 S0024 S0024001 1 INTL 2002026)
ACPI: FACS 3FFCE000, 0040
ACPI: APIC 3FFC0390, 005C (r1 A M I OEMAPIC 1000606 MSFT 97)
ACPI: OEMB 3FFCE040, 0063 (r1 A M I AMI_OEM 1000606 MSFT 97)
ACPI: MCFG 3FFC4890, 003C (r1 A M I OEMMCFG 1000606 MSFT 97)
Scanning NUMA topology in Northbridge 24
No NUMA configuration found
Faking a node at 0000000000000000-000000003ffc0000
Entering add_active_range(0, 0, 159) 0 entries of 3200 used
Entering add_active_range(0, 256, 262080) 1 entries of 3200 used
Bootmem setup node 0 0000000000000000-000000003ffc0000
Zone PFN ranges:
DMA 0 -> 4096
DMA32 4096 -> 1048576
Normal 1048576 -> 1048576
early_node_map[2] active PFN ranges
0: 0 -> 159
0: 256 -> 262080
On node 0 totalpages: 261983
DMA zone: 56 pages used for memmap
DMA zone: 1301 pages reserved
DMA zone: 2642 pages, LIFO batch:0
DMA32 zone: 3527 pages used for memmap
DMA32 zone: 254457 pages, LIFO batch:31
Normal zone: 0 pages used for memmap
Nvidia board detected. Ignoring ACPI timer override.
If you got timer trouble try acpi_use_timer_override
ACPI: PM-Timer IO Port: 0x4008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 (Bootup-CPU)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x81] disabled)
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: BIOS IRQ0 pin2 override ignored.
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ9 used by override.
Setting APIC routing to flat
Using ACPI (MADT) for SMP configuration information
swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000
swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000e8000
swsusp: Registered nosave memory region: 00000000000e8000 - 0000000000100000
Allocating PCI resources starting at 50000000 (gap: 40000000:bec00000)
SMP: Allowing 2 CPUs, 1 hotplug CPUs
PERCPU: Allocating 40968 bytes of per cpu data
Built 1 zonelists. Total pages: 257099
Kernel command line: ro root=/dev/VolGroup00/LogVol00 rhgb ignore_loglevel console=ttyS0,57600n8 crashkernel=256M at 16M
debug: ignoring loglevel setting.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
Extended CMOS year: 2000
time.c: Detected 1800.014 MHz processor.
Console: colour VGA+ 80x25
Checking aperture...
CPU 0: aperture @ 280000000 size 32 MB
Aperture too small (32 MB)
No AGP bridge found
Memory: 762140k/1048320k available (2366k kernel code, 285792k reserved, 1400k data, 312k init)
SLUB: Genslabs=23, HWalign=64, Order=0-1, MinObjects=4, CPUs=2, Nodes=1
Calibrating delay using timer specific routine.. 3601.10 BogoMIPS (lpj=1800552)
Security Framework v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 0/0 -> Node 0
SMP alternatives: switching to UP code
ACPI: Core revision 20070126
Using local APIC timer interrupts.
result 12500103
Detected 12.500 MHz APIC timer.
Brought up 1 CPUs
sizeof(vma)=176 bytes
sizeof(page)=56 bytes
sizeof(inode)=560 bytes
sizeof(dentry)=208 bytes
sizeof(ext3inode)=760 bytes
sizeof(buffer_head)=104 bytes
sizeof(skbuff)=232 bytes
sizeof(task_struct)=2048 bytes
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: BIOS Bug: MCFG area at e0000000 is not E820-reserved
PCI: Not using MMCONFIG.
PCI: Using configuration type 1
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI: Transparent bridge - 0000:00:09.0
PCI: PXH quirk detected, disabling MSI for SHPC device
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P3._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4.P4P5._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P6._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 16 17 18 19) *9
ACPI: PCI Interrupt Link [LNKB] (IRQs 16 17 18 19) *9
ACPI: PCI Interrupt Link [LNKC] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LNKD] (IRQs 16 17 18 19) *10
ACPI: PCI Interrupt Link [LNKE] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LUS0] (IRQs 20 21 22) *9
ACPI: PCI Interrupt Link [LUS1] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [LUS2] (IRQs 20 21 22) *5
ACPI: PCI Interrupt Link [LKLN] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [LAUI] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [LKMO] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [LKSM] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [LTID] (IRQs 20 21 22) *9
ACPI: PCI Interrupt Link [LTIE] (IRQs 20 21 22) *11
ACPI: PCI Interrupt Link [LATA] (IRQs 20 21 22) *14
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 15 devices
ACPI: ACPI bus type pnp unregistered
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
ACPI: RTC can wake from S4
Time: tsc clocksource has been installed.
pnp: 00:07: iomem range 0xffb80000-0xfffffffe could not be reserved
pnp: 00:07: iomem range 0x0-0x0 could not be reserved
pnp: 00:07: iomem range 0x0-0x0 could not be reserved
pnp: 00:07: iomem range 0x0-0x0 could not be reserved
pnp: 00:08: iomem range 0xfec00000-0xfec00fff could not be reserved
pnp: 00:08: iomem range 0xfee00000-0xfeefffff could not be reserved
pnp: 00:0b: ioport range 0x290-0x297 has been reserved
pnp: 00:0d: iomem range 0xe0000000-0xefffffff has been reserved
pnp: 00:0e: iomem range 0x0-0x9ffff could not be reserved
pnp: 00:0e: iomem range 0xc0000-0xdffff has been reserved
pnp: 00:0e: iomem range 0xe0000-0xfffff could not be reserved
pnp: 00:0e: iomem range 0x100000-0x3fffffff could not be reserved
PCI: Bridge: 0000:00:09.0
IO window: e000-efff
MEM window: def00000-dfffffff
PREFETCH window: 50000000-500fffff
PCI: Bridge: 0000:00:0b.0
IO window: disabled.
MEM window: dee00000-deefffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:0c.0
IO window: disabled.
MEM window: ded00000-dedfffff
PREFETCH window: disabled.
PCI: Bridge: 0000:02:00.0
IO window: d000-dfff
MEM window: dec00000-decfffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:0d.0
IO window: d000-dfff
MEM window: dec00000-decfffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:0e.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Setting latency timer of device 0000:00:09.0 to 64
PCI: Setting latency timer of device 0000:00:0b.0 to 64
PCI: Setting latency timer of device 0000:00:0c.0 to 64
PCI: Setting latency timer of device 0000:00:0d.0 to 64
PCI: Setting latency timer of device 0000:02:00.0 to 64
PCI: Setting latency timer of device 0000:00:0e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 6, 262144 bytes)
TCP established hash table entries: 131072 (order: 9, 3145728 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 3848k freed
audit: initializing netlink socket (disabled)
audit(1191363873.954:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
ksign: Installing public key data
Loading keyring
- Added public key 4A67DBB026B0246B
- User ID: Red Hat, Inc. (Kernel Module GPG key)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: Found disabled HT MSI Mapping on 0000:00:0b.0
PCI: Found enabled HT MSI Mapping on 0000:00:00.0
PCI: Found disabled HT MSI Mapping on 0000:00:0c.0
PCI: Found enabled HT MSI Mapping on 0000:00:00.0
PCI: Found disabled HT MSI Mapping on 0000:00:0d.0
PCI: Found enabled HT MSI Mapping on 0000:00:00.0
PCI: Found disabled HT MSI Mapping on 0000:00:0e.0
PCI: Found enabled HT MSI Mapping on 0000:00:00.0
PCI: Setting latency timer of device 0000:00:0b.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0b.0:pcie00]
PCI: Setting latency timer of device 0000:00:0c.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0c.0:pcie00]
PCI: Setting latency timer of device 0000:00:0d.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0d.0:pcie00]
PCI: Setting latency timer of device 0000:00:0e.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0e.0:pcie00]
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI Exception (processor_core-0781): AE_NOT_FOUND, Processor Device is not present [20070126]
Generic RTC Driver v1.07
Non-volatile memory driver v1.2
Linux agpgart interface v0.102 (c) Dave Jones
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
?serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:0c: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 16384K size 4096 blocksize
input: Macintosh mouse button emulation as /class/input/input0
PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
PNP: PS/2 controller doesn't have AUX irq; using default 12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input1
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
powernow-k8: Found 1 AMD Opteron(tm) Processor 144 processors (version 2.00.00)
powernow-k8: 0 : fid 0xa (1800 MHz), vid 0x6
powernow-k8: 1 : fid 0x2 (1000 MHz), vid 0x12
drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
Freeing unused kernel memory: 312k freed
Write protecting the kernel read-only data: 1060k
Red Hat nash version 6.0.9 starting
Mounting proc filesystem
Mounting sysfs filesystem
Creating /dev
Creating initial device nodes
Setting up hotplug.
Creating block device nodes.
LoUSB Universal Host Controller Interface driver v3.0
ading uhci-hcd.ko module
Loadinohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
g ohci-hcd.ko moACPI: PCI Interrupt Link [LUS0] enabled at IRQ 22
dule
ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LUS0] -> GSI 22 (level, low) -> IRQ 22
PCI: Setting latency timer of device 0000:00:02.0 to 64
ohci_hcd 0000:00:02.0: OHCI Host Controller
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:02.0: irq 22, io mem 0xdebfc000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 10 ports detected
Loading ehci-hcd.ko module
ACPI: PCI Interrupt Link [LUS2] enabled at IRQ 21
ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [LUS2] -> GSI 21 (level, low) -> IRQ 21
PCI: Setting latency timer of device 0000:00:02.1 to 64
ehci_hcd 0000:00:02.1: EHCI Host Controller
ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:02.1: debug port 1
PCI: cache line size of 64 is not supported by device 0000:00:02.1
ehci_hcd 0000:00:02.1: irq 21, io mem 0xfeb00000
ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 10 ports detected
input: ImPS/2 Generic Wheel Mouse as /class/input/input2
Loading mbcache.ko module
Loading jbd.ko module
Loading ext3.ko module
Loading scsi_mod.ko module
SCSI subsystem initialized
Loading sd_mod.ko module
Loading scsi_transport_spi.ko module
Loading aic79xx.ko moduleACPI: PCI Interrupt Link [LNKD] enabled at IRQ 19
ACPI: PCI Interrupt 0000:03:04.0[A] -> Link [LNKD] -> GSI 19 (level, low) -> IRQ 19
scsi0 : Adaptec AIC79XX PCI-X SCSI HBA DRIVER, Rev 3.0
<Adaptec 29320LP Ultra320 SCSI adapter>
aic7901A: Ultra320 Wide Channel A, SCSI Id=7, PCI-X 67-100Mhz, 512 SCBs
Loading shpchp.ko module
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
Loading libata.ko module
libata version 2.21 loaded.
Loading sata_nv.ko module
sata_nv 0000:00:07.0: version 3.4
ACPI: PCI Interrupt Link [LTID] enabled at IRQ 20
ACPI: PCI Interrupt 0000:00:07.0[A] -> Link [LTID] -> GSI 20 (level, low) -> IRQ 20
sata_nv 0000:00:07.0: Using ADMA mode
PCI: Setting latency timer of device 0000:00:07.0 to 64
scsi1 : sata_nv
scsi2 : sata_nv
ata1: SATA max UDMA/133 cmd 0xffffc200005e6480 ctl 0xffffc200005e64a0 bmdma 0x0000000000019800 irq 20
ata2: SATA max UDMA/133 cmd 0xffffc200005e6580 ctl 0xffffc200005e65a0 bmdma 0x0000000000019808 irq 20
scsi 0:0:1:0: Direct-Access SEAGATE ST336754LC 0003 PQ: 0 ANSI: 3
target0:0:1: asynchronous
scsi0:A:1:0: Tagged Queuing enabled. Depth 4
target0:0:1: Beginning Domain Validation
target0:0:1: wide asynchronous
target0:0:1: FAST-160 WIDE SCSI 320.0 MB/s DT IU QAS RDSTRM WRFLOW PCOMP (6.25 ns, offset 63)
target0:0:1: Ending Domain Validation
scsi 0:0:2:0: Direct-Access SEAGATE ST336754LC 0003 PQ: 0 ANSI: 3
target0:0:2: asynchronous
scsi0:A:2:0: Tagged Queuing enabled. Depth 4
target0:0:2: Beginning Domain Validation
target0:0:2: wide asynchronous
target0:0:2: FAST-160 WIDE SCSI 320.0 MB/s DT IU QAS RDSTRM WRFLOW PCOMP (6.25 ns, offset 63)
target0:0:2: Ending Domain Validation
ata1: SATA link down (SStatus 0 SControl 300)
ata2: SATA link down (SStatus 0 SControl 300)
ACPI: PCI Interrupt Link [LTIE] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [LTIE] -> GSI 22 (level, low) -> IRQ 22
sata_nv 0000:00:08.0: Using ADMA mode
PCI: Setting latency timer of device 0000:00:08.0 to 64
scsi3 : sata_nv
scsi4 : sata_nv
ata3: SATA max UDMA/133 cmd 0xffffc200005e8480 ctl 0xffffc200005e84a0 bmdma 0x000000000001b400 irq 22
ata4: SATA max UDMA/133 cmd 0xffffc200005e8580 ctl 0xffffc200005e85a0 bmdma 0x000000000001b408 irq 22
ata3: SATA link down (SStatus 0 SControl 300)
ata4: SATA link down (SStatus 0 SControl 300)
Waiting for driver initialization.
sd 0:0:1:0: [sda] 71687372 512-byte hardware sectors (36704 MB)
sd 0:0:1:0: [sda] Write Protect is off
sd 0:0:1:0: [sda] Mode Sense: ab 00 10 08
sd 0:0:1:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
sd 0:0:1:0: [sda] 71687372 512-byte hardware sectors (36704 MB)
sd 0:0:1:0: [sda] Write Protect is off
sd 0:0:1:0: [sda] Mode Sense: ab 00 10 08
sd 0:0:1:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
sda: sda1 sda2
sd 0:0:1:0: [sda] Attached SCSI disk
sd 0:0:2:0: [sdb] 71687372 512-byte hardware sectors (36704 MB)
sd 0:0:2:0: [sdb] Write Protect is off
sd 0:0:2:0: [sdb] Mode Sense: ab 00 10 08
sd 0:0:2:0: [sdb] Write cache: enabled, read cache: enabled, supports DPO and FUA
sd 0:0:2:0: [sdb] 71687372 512-byte hardware sectors (36704 MB)
sd 0:0:2:0: [sdb] Write Protect is off
sd 0:0:2:0: [sdb] Mode Sense: ab 00 10 08
sd 0:0:2:0: [sdb] Write cache: enabled, read cache: enabled, supports DPO and FUA
sdb: sdb1 sdb2
sd 0:0:2:0: [sdb] Attached SCSI disk
Loading pata_amd.ko module
pata_amd 0000:00:06.0: version 0.3.8
PCI: Setting latency timer of device 0000:00:06.0 to 64
scsi5 : pata_amd
scsi6 : pata_amd
ata5: PATA max UDMA/133 cmd 0x00000000000101f0 ctl 0x00000000000103f6 bmdma 0x0000000000013000 irq 14
ata6: PATA max UDMA/133 cmd 0x0000000000010170 ctl 0x0000000000010376 bmdma 0x0000000000013008 irq 15
ata5.01: ATAPI: LITE-ON CD-ROM LTN-5291S, NS08, max UDMA/33
ata5.01: configured for UDMA/33
scsi 5:0:1:0: CD-ROM LITE-ON CD-ROM LTN-5291S NS08 PQ: 0 ANSI: 5
Waiting for driver initialization.
Loading dm-mod.ko module
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel at redhat.com
Loading dm-mirror.ko module
Loading dm-zero.ko module
Loading dm-snapshot.ko module
Making device-mapper control node
Scanning logical volumes
Reading all physical volumes. This may take a while...
Found volume group "VolGroup00" using metadata type lvm2
Activating logical volumes
2 logical volume(s) in volume group "VolGroup00" now active
Trying to resume from /dev/VolGroup00/LogVol01
No suspend signature on swap, not resuming.
Creating root device.
Mounting root filesystem.
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting. Commit interval 5 seconds
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
Setting up other filesystems.
Setting up new root fs
no fstab.sys, mounting internal defaults
Switching to new root and running init.
unmounting old /dev
unmounting old /proc
unmounting old /sys
security: 3 users, 6 roles, 1827 types, 80 bools, 1 sens, 1024 cats
security: 61 classes, 68491 rules
SELinux: Completing initialization.
SELinux: Setting up existing superblocks.
SELinux: initialized (dev dm-0, type ext3), uses xattr
SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev debugfs, type debugfs), uses genfs_contexts
SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts
SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs
SELinux: initialized (dev hugetlbfs, type hugetlbfs), uses genfs_contexts
SELinux: initialized (dev devpts, type devpts), uses transition SIDs
SELinux: initialized (dev inotifyfs, type inotifyfs), uses genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev futexfs, type futexfs), uses genfs_contexts
SELinux: initialized (dev anon_inodefs, type anon_inodefs), not configured for labeling
SELinux: initialized (dev pipefs, type pipefs), uses task SIDs
SELinux: initialized (dev sockfs, type sockfs), uses task SIDs
SELinux: initialized (dev cpuset, type cpuset), uses genfs_contexts
SELinux: initialized (dev proc, type proc), uses genfs_contexts
SELinux: initialized (dev bdev, type bdev), uses genfs_contexts
SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts
SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
audit(1191363903.172:2): policy loaded auid=4294967295
INIT: version 2.86 booting
Welcome to Fedora
Press 'I' to enter interactive startup.
Setting clock (utc): Tue Oct 2 18:25:06 EDT 2007 [ OK ]
Starting udev: sd 0:0:1:0: Attached scsi generic sg0 type 0
sd 0:0:2:0: Attached scsi generic sg1 type 0
scsi 5:0:1:0: Attached scsi generic sg2 type 5
sr0: scsi3-mmc drive: 0x/52x cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
Floppy drive(s): fd0 is 1.44M
sr 5:0:1:0: Attached scsi CD-ROM sr0
FDC 0 is a post-1991 82077
i2c-adapter i2c-0: nForce2 SMBus adapter at 0x4c00
i2c-adapter i2c-1: nForce2 SMBus adapter at 0x4c40
rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one year, y3k
parport_pc 00:06: reported by Plug and Play ACPI
parport0: PC-style at 0x378, irq 7 [PCSPP]
tg3.c:v3.77 (May 31, 2007)
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 18
ACPI: PCI Interrupt 0000:05:00.0[A] -> Link [LNKB] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:05:00.0 to 64
eth0: Tigon3 [partno(BCM95721) rev 4101 PHY(5750)] (PCI Express) 10/100/1000Base-T Ethernet 00:15:f2:d0:d9:2d
eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] WireSpeed[1] TSOcap[1]
eth0: dma_rwctrl[76180000] dma_mask[64-bit]
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 17
ACPI: PCI Interrupt 0000:04:00.0[A] -> Link [LNKA] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:04:00.0 to 64
eth1: Tigon3 [partno(BCM95721) rev 4101 PHY(5750)] (PCI Express) 10/100/1000Base-T Ethernet 00:15:f2:d0:d8:65
eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] WireSpeed[1] TSOcap[1]
eth1: dma_rwctrl[76180000] dma_mask[64-bit]
QLogic Fibre Channel HBA Driver
ACPI: PCI Interrupt 0000:03:00.0[A] -> Link [LNKD] -> GSI 19 (level, low) -> IRQ 19
qla2xxx 0000:03:00.0: Found an ISP2312, irq 19, iobase 0xffffc200005ea000
qla2xxx 0000:03:00.0: Configuring PCI space...
qla2xxx 0000:03:00.0: Configure NVRAM parameters...
qla2xxx 0000:03:00.0: Verifying loaded RISC code...
qla2xxx 0000:03:00.0: Allocated (412 KB) for firmware dump...
qla2xxx 0000:03:00.0: LIP reset occured (fd5a).
scsi7 : qla2xxx
qla2xxx 0000:03:00.0:
QLogic Fibre Channel HBA Driver: 8.01.07-k7
QLogic QLA2340 - 133MHz PCI-X to 2Gb FC, Single Channel
ISP2312: PCI-X (100 MHz) @ 0000:03:00.0 hdma-, host#=7, fw=3.03.20 IPX
[ OK ]
loop: module loaded
qla2xxx 0000:03:00.0: LIP occured (f7f7).
qla2xxx 0000:03:00.0: LOOP UP detected (2 Gbps).
lp0: using parport0 (interrupt-driven).
lp0: console ready
Loading default keymap (us): [ OK ]
Setting hostname don2: [ OK ]
No dock devices found.
input: Power Button (FF) as /class/input/input3
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input4
ACPI: Power Button (CM) [PWRB]
device-mapper: multipath: version 1.0.5 loaded
scsi 7:0:0:0: Sequential-Access QUANTUM SDLT320 V62 PQ: 0 ANSI: 3
scsi 7:0:0:1: Medium Changer STK L700 3.05 PQ: 0 ANSI: 3
scsi 7:0:0:2: Sequential-Access IBM ULTRIUM-TD2 333K PQ: 0 ANSI: 3
scsi 7:0:0:3: Sequential-Access IBM ULTRIUM-TD2 333K PQ: 0 ANSI: 3
scsi 7:0:0:4: Sequential-Access IBM ULTRIUM-TD1 18N2 PQ: 0 ANSI: 3
scsi 7:0:0:5: Sequential-Access IBM ULTRIUM-TD1 18N2 PQ: 0 ANSI: 3
scsi 7:0:0:6: Sequential-Access IBM ULTRIUM-TD1 18N2 PQ: 0 ANSI: 3
scsi 7:0:0:7: Sequential-Access IBM ULTRIUM-TD1 18N2 PQ: 0 ANSI: 3
scsi 7:0:0:0: Attached scsi generic sg3 type 1
scsi 7:0:0:1: Attached scsi generic sg4 type 8
scsi 7:0:0:2: Attached scsi generic sg5 type 1
scsi 7:0:0:3: Attached scsi generic sg6 type 1
scsi 7:0:0:4: Attached scsi generic sg7 type 1
scsi 7:0:0:5: Attached scsi generic sg8 type 1
scsi 7:0:0:6: Attached scsi generic sg9 type 1
scsi 7:0:0:7: Attached scsi generic sg10 type 1
st: Version 20070203, fixed bufsize 32768, s/g segs 256
st 7:0:0:0: Attached scsi tape st0
st 7:0:0:0: st0: try direct i/o: yes (alignment 512 B)
st 7:0:0:2: Attached scsi tape st1
st 7:0:0:2: st1: try direct i/o: yes (alignment 512 B)
st 7:0:0:3: Attached scsi tape st2
st 7:0:0:3: st2: try direct i/o: yes (alignment 512 B)
osst :I: Tape driver with OnStream support version 0.99.4
osst :I: $Id: osst.c,v 1.73 2005/01/01 21:13:34 wriede Exp $
st 7:0:0:4: Attached scsi tape st3
st 7:0:0:4: st3: try direct i/o: yes (alignment 512 B)
st 7:0:0:5: Attached scsi tape st4
st 7:0:0:5: st4: try direct i/o: yes (alignment 512 B)
st 7:0:0:6: Attached scsi tape st5
st 7:0:0:6: st5: try direct i/o: yes (alignment 512 B)
st 7:0:0:7: Attached scsi tape st6
st 7:0:0:7: st6: try direct i/o: yes (alignment 512 B)
Setting up Logical Volume Management: 2 logical volume(s) in volume group "VolGroup00" now active
[ OK ]
Checking filesystems
Checking all file systems.
[/sbin/fsck.ext3 (1) -- /] fsck.ext3 -a /dev/VolGroup00/LogVol00
/dev/VolGroup00/LogVol00: clean, 281817/8421376 files, 2220679/8413184 blocks
[/sbin/fsck.ext3 (1) -- /boot] fsck.ext3 -a /dev/sda1
/boot: recovering journal
/boot: clean, 39/26104 files, 25972/104388 blocks
[ OK ]
Remounting root filesystem in read-write mode: EXT3 FS on dm-0, internal journal
[ OK ]
Mounting local filesystems: kjournald starting. Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev sda1, type ext3), uses xattr
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
[ OK ]
Enabling local filesystem quotas: [ OK ]
Enabling /etc/fstab swaps: Adding 2031608k swap on /dev/VolGroup00/LogVol01. Priority:-1 extents:1 across:2031608k
[ OK ]
SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses genfs_contexts
INIT: Entering runlevel: 5
Entering non-interactive startup
Starting background readahead (early, fast mode): [ OK ]
Checking for hardware changes [ OK ]
Enabling ondemand cpu frequency scaling: [ OK ]
Applying iptables firewall rules: ip_tables: (C) 2000-2006 Netfilter Core Team
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (4095 buckets, 32760 max)
[ OK ]
Loading additional iptables modules: ip_conntrack_netbios_ns [ OK ]
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
Mobile IPv6
Bringing up loopback interface: [ OK ]
Bringing up interface eth0:
Determining IP information for eth0...ADDRCONF(NETDEV_UP): eth0: link is not ready
Marking TSC unstable due to cpufreq changes
Time: acpi_pm clocksource has been installed.
tg3: eth0: Link is up at 1000 Mbps, full duplex.
tg3: eth0: Flow control is on for TX and on for RX.
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
tg3: eth0: Link is down.
tg3: eth0: Link is up at 1000 Mbps, full duplex.
tg3: eth0: Flow control is on for TX and on for RX.
done.
[ OK ]
Starting auditd: audit(1191363929.780:3): audit_pid=2153 old=0 by auid=4294967295 subj=system_u:system_r:auditd_t:s0
[ OK ]
Starting restorecond: [ OK ]
Starting system logger: [ OK ]
Starting kernel logger: [ OK ]
Starting irqbalance: [ OK ]
Starting mcstransd: [ OK ]
Starting rpcbind: [ OK ]
eth0: no IPv6 routers present
Starting setroubleshootd: [ OK ]
Starting NFS statd: [ OK ]
Starting RPC idmapd: SELinux: initialized (dev rpc_pipefs, type rpc_pipefs), uses genfs_contexts
[ OK ]
Starting kdump:[ OK ]
Starting system message bus: [ OK ]
Mounting other filesystems: [ OK ]
Starting PC/SC smart card daemon (pcscd): [ OK ]
Starting hidd: Bluetooth: Core ver 2.11
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ OK ]
Starting autofs: Loading autofs4: [ OK ]
Starting automount: SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
[ OK ]
[ OK ]
Starting hpiod: [ OK ]
Starting hpssd: [ OK ]
Starting sshd: [ OK ]
ntpd: Synchronizing with time server: [ OK ]
Starting ntpd: [ OK ]
Starting postgresql service: [ OK ]
Starting sendmail: [ OK ]
Starting sm-client: [ OK ]
Starting ConsoleKit: [ OK ]
Starting crond: [ OK ]
Enabling monthly Smolt checkin: [ OK ]
Starting xfs: [ OK ]
Starting anacron: [ OK ]
Starting atd: [ OK ]
Starting background readahead (later, fast mode): [ OK ]
Starting dhcdbd:[ OK ]
Starting Avahi daemon... [ OK ]
Starting HAL daemon: [ OK ]
Starting smartd: [ OK ]
More information about the fedora-list
mailing list