Kernel 2.6.24.x boot problem
Nicolae Ghimbovschi
xfreebird at gmail.com
Fri Apr 4 10:28:51 UTC 2008
Anyone , Any idea ?
On Wed, Apr 2, 2008 at 1:06 AM, Nicolae Ghimbovschi <xfreebird at gmail.com>
wrote:
> Hello,
>
> Starting with kernel 2.6.24.3-34.fc8 Fedora fails to boot.
>
> It works well with 2.6.23.15-137.fc8 and lower versions.
>
> The error messages are listed below:
> ...
> Loading pata_via.ko module
> ACPI: Unable to derive IRQ for device 0000:00:11.1
> scsi0: pata_via
> scsi1: pata_via
> ata1: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmda 0xfc00 irq 14
> ata2: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmda 0xfc08 irq 14
> ata1.00 ATA-7: Maxtor 6Y80L0, YAR41BW0, max UDMA/133
> ata1.00: 160086528 sectors, multi 16: LBA48
> ata1.00: configured for UDMA/133
> ata2.00: ATAPI: ASUS CRW-5232AS, 1.03, max UDMA/33
> ata2.01: ATAPI: CDU5211, YYS7, max UDMA/33
> ata2.00: configured for UDMA/33
> ata2.01: configured for UDMA/33
> scsi 0:0:0:0: Direct-Access ATA Maxtor 6Y80L0 YAR4 PQ: 0 ANSI: 5
> sd 0:0:0:0: [sda] 160086528 512-byte hardware sectors (81964 MB)
> sd 0:0:0:0: [sda] Write protect is off
> sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't
> support DPO or FUA
> sda:<3>ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
> ata1.00: BMDMA stat 0x24
> ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
> res 51/84:00:00:00:00/00:00:00:00:00/e0 Emask 0x10 (ATA bus
> error)
> ata1.00: status: { DRDY ERR }
> ata1.00: error: { ICRC ABRT }
> ata1: soft resetting link
> ata1.00: configured for UDMA/133
> ata1: EH complete
> ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
> ata1.00: BMDMA stat 0x24
> ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
> res 51/84:00:00:00:00/00:00:00:00:00/e0 Emask 0x10 (ATA bus
> error)
> ata1.00: status: { DRDY ERR }
> ata1.00: error: { ICRC ABRT }
> ata1: soft resetting link
> ata1.00: configured for UDMA/133
> ata1: EH complete
> ata1.00: limiting speed to UDMA/100:PI04
> ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
> ata1.00: BMDMA stat 0x24
> ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
> res 51/84:00:00:00:00/00:00:00:00:00/e0 Emask 0x10 (ATA bus
> error)
> ata1.00: status: { DRDY ERR }
> ata1.00: error: { ICRC ABRT }
> ata1: soft resetting link
> ata1.00: configured for UDMA/100
> ata1: EH complete
> ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
> ata1.00: BMDMA stat 0x24
> ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
> res 51/84:00:00:00:00/00:00:00:00:00/e0 Emask 0x10 (ATA bus
> error)
> ata1.00: status: { DRDY ERR }
> ata1.00: error: { ICRC ABRT }
> ata1: soft resetting link
> ata1.00: configured for UDMA/100
> sd 0:0:0:0 [sda] Result: hostbyte=DID_OK
> driverbyte=DRIVER_SENSE,SUGGEST_OK
> sd 0:0:0:0 [sda] Sense Key : Aborted Command [current] [descriptor]
> Descriptor sense data with sense descriptor (in hex):
> 72 0b 47 00 00 00 00 0c 00 0a 80 00 00 00 00 00
> 00 00 00 00
> sd 0:0:0: [sda] Add. Sense: Scsi parity error
> end_request: I/O error, dev sda, sector 0
> Buffer I/O error on device sda, logical block 0
> ata1: EH complete
> .....
> Dev sda: unable to read RDB block 0
> unable to read partition table
> .....
> Unable to access resume device (LABEL=SWAP-sda3)
> mount: could not find filesystem '/dev/root'
> setuproot: moving /dev/failed: No such file or directory
> setuproot: error mounting /proc: No such file or directory
> setuproot: error mounting /sys: No such file or directory
> switchroot: mount failed: No such file or directory
> Boot has failed.
>
>
>
> *******************************************************************
> My system:
>
> 00:11.1 IDE interface [0101]: VIA Technologies, Inc.
> VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE [1106:0571] (rev 06)
> Kernel driver in use: pata_via
> Kernel modules: pata_via
>
> /dev/sda:
>
> ATA device, with non-removable media
> Model Number: Maxtor 6Y080L0
> Serial Number: Y26DPFZE
> Firmware Revision: YAR41BW0
> Standards:
> Used: ATA/ATAPI-7 T13 1532D revision 0
> Supported: 7 6 5 4
> Configuration:
> Logical max current
> cylinders 16383 4047
> heads 16 16
> sectors/track 63 255
> --
> CHS current addressable sectors: 16511760
> LBA user addressable sectors: 160086528
> LBA48 user addressable sectors: 160086528
> device size with M = 1024*1024: 78167 MBytes
> device size with M = 1000*1000: 81964 MBytes (81 GB)
> Capabilities:
> LBA, IORDY(can be disabled)
> Standby timer values: spec'd by Standard, no device specific
> minimum
> R/W multiple sector transfer: Max = 16 Current = 16
> Advanced power management level: unknown setting (0x0000)
> Recommended acoustic management value: 192, current value: 254
> DMA: mdma0 mdma1 mdma2 udma0 udma1 *udma2 udma3 udma4 udma5 udma6
> Cycle time: min=120ns recommended=120ns
> PIO: pio0 pio1 pio2 pio3 pio4
> Cycle time: no flow control=120ns IORDY flow control=120ns
> Commands/features:
> Enabled Supported:
> * SMART feature set
> Security Mode feature set
> * Power Management feature set
> * Write cache
> * Look-ahead
> * Host Protected Area feature set
> * WRITE_VERIFY command
> * WRITE_BUFFER command
> * READ_BUFFER command
> * NOP cmd
> * DOWNLOAD_MICROCODE
> Advanced Power Management feature set
> SET_MAX security extension
> * Automatic Acoustic Management feature set
> * 48-bit Address feature set
> * Device Configuration Overlay feature set
> * Mandatory FLUSH_CACHE
> * FLUSH_CACHE_EXT
> * SMART error logging
> * SMART self-test
> Security:
> Master password revision code = 65534
> supported
> not enabled
> not locked
> not frozen
> not expired: security count
> not supported: enhanced erase
> HW reset results:
> CBLID- above Vih
> Device num = 0 determined by the jumper
> Checksum: correct
> ***********************************************************
>
> dmesg from the working kernel :
>
> Linux version 2.6.23.15-137.fc8 (mockbuild at xenbuilder2.fedora.redhat.com)
> (gcc version 4.1.2 20070925 (Red Hat 4.1.2-33)) #1 SMP Sun Feb 10 17:48:34
> EST 2008
> BIOS-provided physical RAM map:
> BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
> BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
> BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
> BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
> BIOS-e820: 000000001fff0000 - 000000001fff8000 (ACPI data)
> BIOS-e820: 000000001fff8000 - 0000000020000000 (ACPI NVS)
> BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
> BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
> BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
> 0MB HIGHMEM available.
> 511MB LOWMEM available.
> found SMP MP-table at 000fb820
> Using x86 segment limits to approximate NX protection
> Entering add_active_range(0, 0, 131056) 0 entries of 256 used
> Zone PFN ranges:
> DMA 0 -> 4096
> Normal 4096 -> 131056
> HighMem 131056 -> 131056
> Movable zone start PFN for each node
> early_node_map[1] active PFN ranges
> 0: 0 -> 131056
> On node 0 totalpages: 131056
> DMA zone: 32 pages used for memmap
> DMA zone: 0 pages reserved
> DMA zone: 4064 pages, LIFO batch:0
> Normal zone: 991 pages used for memmap
> Normal zone: 125969 pages, LIFO batch:31
> HighMem zone: 0 pages used for memmap
> Movable zone: 0 pages used for memmap
> DMI 2.3 present.
> Using APIC driver default
> ACPI: RSDP 000FA4A0, 0014 (r0 AMI )
> ACPI: RSDT 1FFF0000, 002C (r1 AMIINT VIA_K7 10 MSFT 97)
> ACPI: FACP 1FFF0030, 0081 (r1 AMIINT VIA_K7 11 MSFT 97)
> ACPI: DSDT 1FFF0120, 30F2 (r1 VIA VIA_K7 1000 MSFT 100000D)
> ACPI: FACS 1FFF8000, 0040
> ACPI: APIC 1FFF00C0, 0054 (r1 AMIINT VIA_K7 9 MSFT 97)
> ACPI: PM-Timer IO Port: 0x808
> ACPI: Local APIC address 0xfee00000
> ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
> Processor #0 6:8 APIC version 16
> ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
> IOAPIC[0]: apic_id 2, version 3, address 0xfec00000, GSI 0-23
> ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
> ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
> ACPI: IRQ0 used by override.
> ACPI: IRQ2 used by override.
> ACPI: IRQ9 used by override.
> Enabling APIC mode: Flat. Using 1 I/O APICs
> Using ACPI (MADT) for SMP configuration information
> Allocating PCI resources starting at 30000000 (gap: 20000000:dec00000)
> swsusp: Registered nosave memory region: 000000000009f000 -
> 00000000000a0000
> swsusp: Registered nosave memory region: 00000000000a0000 -
> 00000000000f0000
> swsusp: Registered nosave memory region: 00000000000f0000 -
> 0000000000100000
> Built 1 zonelists in Zone order. Total pages: 130033
> Kernel command line: ro root=LABEL=/1 rhgb quiet
> mapped APIC to ffffb000 (fee00000)
> mapped IOAPIC to ffffa000 (fec00000)
> Enabling fast FPU save and restore... done.
> Enabling unmasked SIMD FPU exception support... done.
> Initializing CPU#0
> CPU 0 irqstacks, hard=c07a9000 soft=c0789000
> PID hash table entries: 2048 (order: 11, 8192 bytes)
> Detected 1666.449 MHz processor.
> Console: colour VGA+ 80x25
> console [tty0] enabled
> Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
> Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
> Memory: 511596k/524224k available (2187k kernel code, 11944k reserved,
> 1118k data, 280k init, 0k highmem)
> virtual kernel memory layout:
> fixmap : 0xffc53000 - 0xfffff000 (3760 kB)
> pkmap : 0xff800000 - 0xffc00000 (4096 kB)
> vmalloc : 0xe0800000 - 0xff7fe000 ( 495 MB)
> lowmem : 0xc0000000 - 0xdfff0000 ( 511 MB)
> .init : 0xc0740000 - 0xc0786000 ( 280 kB)
> .data : 0xc0622d15 - 0xc073a544 (1118 kB)
> .text : 0xc0400000 - 0xc0622d15 (2187 kB)
> Checking if this processor honours the WP bit even in supervisor mode...
> Ok.
> SLUB: Genslabs=22, HWalign=32, Order=0-1, MinObjects=4, CPUs=1, Nodes=1
> Calibrating delay using timer specific routine.. 3335.44 BogoMIPS
> (lpj=1667720)
> Security Framework v1.0.0 initialized
> SELinux: Initializing.
> SELinux: Starting in permissive mode
> selinux_register_security: Registering secondary module capability
> Capability LSM initialized as secondary
> Mount-cache hash table entries: 512
> CPU: After generic identify, caps: 0383fbff c1c3fbff 00000000 00000000
> 00000000 00000000 00000000 00000000
> CPU: CLK_CTL MSR was 6003d22f. Reprogramming to 2003d22f
> CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
> CPU: L2 Cache: 256K (64 bytes/line)
> CPU: After all inits, caps: 0383f3ff c1c3fbff 00000000 00000420 00000000
> 00000000 00000000 00000000
> Intel machine check architecture supported.
> Intel machine check reporting enabled on CPU#0.
> Compat vDSO mapped to ffffe000.
> Checking 'hlt' instruction... OK.
> SMP alternatives: switching to UP code
> Freeing SMP alternatives: 14k freed
> ACPI: Core revision 20070126
> CPU0: AMD Athlon(tm) XP 2000+ stepping 01
> Total of 1 processors activated (3335.44 BogoMIPS).
> ENABLING IO-APIC IRQs
> ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
> Brought up 1 CPUs
> sizeof(vma)=84 bytes
> sizeof(page)=32 bytes
> sizeof(inode)=336 bytes
> sizeof(dentry)=132 bytes
> sizeof(ext3inode)=488 bytes
> sizeof(buffer_head)=56 bytes
> sizeof(skbuff)=180 bytes
> sizeof(task_struct)=1552 bytes
> Booting paravirtualized kernel on bare hardware
> Time: 0:19:32 Date: 04/02/08
> NET: Registered protocol family 16
> No dock devices found.
> ACPI: bus type pci registered
> PCI: PCI BIOS revision 2.10 entry at 0xfdaf1, last bus=1
> PCI: Using configuration type 1
> Setting up standard PCI resources
> ACPI: EC: Look up EC in DSDT
> ACPI: Interpreter enabled
> ACPI: (supports S0 S1 S4 S5)
> ACPI: Using IOAPIC for interrupt routing
> ACPI: PCI Root Bridge [PCI0] (0000:00)
> PCI quirk: region 0800-087f claimed by vt8235 PM
> PCI quirk: region 0400-040f claimed by vt8235 SMB
> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
> ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11 12 14 15)
> ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
> ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15)
> ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 *11 12 14 15)
> ACPI: Power Resource [URP1] (off)
> ACPI: Power Resource [URP2] (off)
> ACPI: Power Resource [FDDP] (off)
> ACPI: Power Resource [LPTP] (off)
> Linux Plug and Play Support v0.97 (c) Adam Belay
> pnp: PnP ACPI init
> ACPI: bus type pnp registered
> pnp: PnP ACPI: found 11 devices
> ACPI: ACPI bus type pnp unregistered
> usbcore: registered new interface driver usbfs
> usbcore: registered new interface driver hub
> usbcore: registered new device driver usb
> PCI: Using ACPI for IRQ routing
> PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a
> report
> NetLabel: Initializing
> NetLabel: domain hash size = 128
> NetLabel: protocols = UNLABELED CIPSOv4
> NetLabel: unlabeled traffic allowed by default
> Time: tsc clocksource has been installed.
> pnp: 00:01: iomem range 0xfee00000-0xfee00fff could not be reserved
> PCI: Bridge: 0000:00:01.0
> IO window: disabled.
> MEM window: dde00000-dfefffff
> PREFETCH window: cdd00000-ddcfffff
> PCI: Setting latency timer of device 0000:00:01.0 to 64
> NET: Registered protocol family 2
> IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
> TCP established hash table entries: 16384 (order: 5, 196608 bytes)
> TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
> TCP: Hash tables configured (established 16384 bind 16384)
> TCP reno registered
> checking if image is initramfs... it is
> Freeing initrd memory: 2963k freed
> apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
> apm: overridden by ACPI.
> audit: initializing netlink socket (disabled)
> audit(1207095572.455:1): initialized
> Total HugeTLB memory allocated, 0
> VFS: Disk quotas dquot_6.5.1
> Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
> SELinux: Registering netfilter hooks
> ksign: Installing public key data
> Loading keyring
> - Added public key 433CDEB37FB53040
> - User ID: Red Hat, Inc. (Kernel Module GPG key)
> Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
> io scheduler noop registered
> io scheduler anticipatory registered
> io scheduler deadline registered
> io scheduler cfq registered (default)
> PCI: VIA PCI bridge detected. Disabling DAC.
> Boot video device is 0000:01:00.0
> pci_hotplug: PCI Hot Plug PCI Core version: 0.5
> ACPI: Processor [CPU1] (supports 16 throttling states)
> isapnp: Scanning for PnP cards...
> Switched to high resolution mode on CPU 0
> isapnp: No Plug & Play device found
> Real Time Clock Driver v1.12ac
> Non-volatile memory driver v1.2
> Linux agpgart interface v0.102
> agpgart: Detected VIA KM400/KM400A chipset
> agpgart: AGP aperture is 64M @ 0xe0000000
> Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
> serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
> 00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
> RAMDISK driver initialized: 16 RAM disks of 16384K size 4096 blocksize
> input: Macintosh mouse button emulation as /class/input/input0
> PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
> serio: i8042 KBD port at 0x60,0x64 irq 1
> serio: i8042 AUX port at 0x60,0x64 irq 12
> mice: PS/2 mouse device common for all mice
> input: AT Translated Set 2 keyboard as /class/input/input1
> cpuidle: using governor menu
> usbcore: registered new interface driver hiddev
> usbcore: registered new interface driver usbhid
> drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
> TCP cubic registered
> Initializing XFRM netlink socket
> NET: Registered protocol family 1
> NET: Registered protocol family 17
> powernow-k8: Processor cpuid 681 not supported
> Using IPI No-Shortcut mode
> Magic number: 4:403:303
> hash matches device tty32
> Freeing unused kernel memory: 280k freed
> Write protecting the kernel read-only data: 850k
> input: GenPS/2 Genius Mouse as /class/input/input2
> ACPI: PCI Interrupt 0000:00:10.3[D] -> GSI 21 (level, low) -> IRQ 16
> ehci_hcd 0000:00:10.3: EHCI Host Controller
> ehci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 1
> ehci_hcd 0000:00:10.3: irq 16, io mem 0xdffff700
> ehci_hcd 0000:00:10.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
> usb usb1: configuration #1 chosen from 1 choice
> hub 1-0:1.0: USB hub found
> hub 1-0:1.0: 6 ports detected
> ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
> USB Universal Host Controller Interface driver v3.0
> ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 16
> uhci_hcd 0000:00:10.0: UHCI Host Controller
> uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2
> uhci_hcd 0000:00:10.0: irq 16, io base 0x0000e000
> usb usb2: configuration #1 chosen from 1 choice
> hub 2-0:1.0: USB hub found
> hub 2-0:1.0: 2 ports detected
> ACPI: PCI Interrupt 0000:00:10.1[B] -> GSI 21 (level, low) -> IRQ 16
> uhci_hcd 0000:00:10.1: UHCI Host Controller
> uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
> uhci_hcd 0000:00:10.1: irq 16, io base 0x0000e400
> usb usb3: configuration #1 chosen from 1 choice
> hub 3-0:1.0: USB hub found
> hub 3-0:1.0: 2 ports detected
> ACPI: PCI Interrupt 0000:00:10.2[C] -> GSI 21 (level, low) -> IRQ 16
> uhci_hcd 0000:00:10.2: UHCI Host Controller
> uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4
> uhci_hcd 0000:00:10.2: irq 16, io base 0x0000e800
> usb usb4: configuration #1 chosen from 1 choice
> hub 4-0:1.0: USB hub found
> hub 4-0:1.0: 2 ports detected
> SCSI subsystem initialized
> libata version 2.21 loaded.
> pata_via 0000:00:11.1: version 0.3.2
> ACPI: Unable to derive IRQ for device 0000:00:11.1
> scsi0 : pata_via
> scsi1 : pata_via
> ata1: PATA max UDMA/133 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x0001fc00 irq
> 14
> ata2: PATA max UDMA/133 cmd 0x00010170 ctl 0x00010376 bmdma 0x0001fc08 irq
> 15
> usb 2-2: new full speed USB device using uhci_hcd and address 2
> ata1.00: ATA-7: Maxtor 6Y080L0, YAR41BW0, max UDMA/133
> ata1.00: 160086528 sectors, multi 16: LBA48
> ata1.00: limited to UDMA/33 due to 40-wire cable
> ata1.00: configured for UDMA/33
> usb 2-2: configuration #1 chosen from 1 choice
> ata2.00: ATAPI: ASUS CRW-5232AS, 1.03, max UDMA/33
> ata2.01: ATAPI: CDU5211, YYS7, max UDMA/33
> ata2.00: configured for UDMA/33
> ata2.01: configured for UDMA/33
> scsi 0:0:0:0: Direct-Access ATA Maxtor 6Y080L0 YAR4 PQ: 0 ANSI:
> 5
> sd 0:0:0:0: [sda] 160086528 512-byte hardware sectors (81964 MB)
> sd 0:0:0:0: [sda] Write Protect is off
> sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
> sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't
> support DPO or FUA
> sd 0:0:0:0: [sda] 160086528 512-byte hardware sectors (81964 MB)
> sd 0:0:0:0: [sda] Write Protect is off
> sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
> sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't
> support DPO or FUA
> sda: sda1 sda2 sda3 sda4 < sda5 >
> sd 0:0:0:0: [sda] Attached SCSI disk
> scsi 1:0:0:0: CD-ROM ASUS CRW-5232AS 1.03 PQ: 0 ANSI:
> 5
> scsi 1:0:1:0: CD-ROM SONY CD-ROM CDU5211 YYS7 PQ: 0 ANSI:
> 5
> kjournald starting. Commit interval 5 seconds
> EXT3-fs: mounted filesystem with ordered data mode.
> SELinux: Disabled at runtime.
> SELinux: Unregistering netfilter hooks
> audit(1207095578.532:2): selinux=0 auid=4294967295
> sr0: scsi3-mmc drive: 52x/52x writer cd/rw xa/form2 cdda tray
> Uniform CD-ROM driver Revision: 3.20
> sr 1:0:0:0: Attached scsi CD-ROM sr0
> sr1: scsi3-mmc drive: 52x/52x cd/rw xa/form2 cdda tray
> sr 1:0:1:0: Attached scsi CD-ROM sr1
> sd 0:0:0:0: Attached scsi generic sg0 type 0
> sr 1:0:0:0: Attached scsi generic sg1 type 5
> sr 1:0:1:0: Attached scsi generic sg2 type 5
> usblp0: USB Bidirectional printer dev 2 if 0 alt 0 proto 2 vid 0x03F0 pid
> 0xC302
> usbcore: registered new interface driver usblp
> input: Power Button (FF) as /class/input/input3
> ACPI: Power Button (FF) [PWRF]
> input: Power Button (CM) as /class/input/input4
> ACPI: Power Button (CM) [PWRB]
> input: Sleep Button (CM) as /class/input/input5
> ACPI: Sleep Button (CM) [SLPB]
> via-rhine.c:v1.10-LK1.4.3 2007-03-06 Written by Donald Becker
> ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 23 (level, low) -> IRQ 17
> eth0: VIA Rhine II at 0xdffff600, 00:30:1b:2b:a1:c1, IRQ 17.
> eth0: MII PHY found at address 1, status 0x786d advertising 01e1 Link
> 45e1.
> input: PC Speaker as /class/input/input6
> NET: Registered protocol family 23
> Floppy drive(s): fd0 is 1.44M
> FDC 0 is a post-1991 82077
> nvidia: module license 'NVIDIA' taints kernel.
> parport_pc 00:0a: reported by Plug and Play ACPI
> parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE]
> ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 18
> NVRM: loading NVIDIA Linux x86 Kernel Module 96.43.05 Tue Jan 22
> 19:36:58 PST 2008
> ACPI: PCI Interrupt 0000:00:11.5[C] -> GSI 22 (level, low) -> IRQ 19
> PCI: Setting latency timer of device 0000:00:11.5 to 64
> NET: Registered protocol family 10
> lo: Disabled Privacy Extensions
> agpgart: Found an AGP 3.5 compliant device at 0000:00:00.0.
> agpgart: BIOS bug. AGP bridge claims to only support x4 rateFixing up
> support for x2 & x1
> agpgart: Device is in legacy mode, falling back to 2.x
> agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode
> agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x mode
> device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised:
> dm-devel at redhat.com
> device-mapper: multipath: version 1.0.5 loaded
> EXT3 FS on sda2, internal journal
> Adding 1020116k swap on /dev/sda3. Priority:-1 extents:1 across:1020116k
> ip6_tables: (C) 2000-2006 Netfilter Core Team
> Netfilter messages via NETLINK v0.30.
> nf_conntrack version 0.5.0 (8192 buckets, 32768 max)
> ip_tables: (C) 2000-2006 Netfilter Core Team
> eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
> fuse init (API version 7.8)
> audit(1207084803.854:3): audit_pid=1749 old=0 by auid=4294967295
> Bluetooth: Core ver 2.11
> NET: Registered protocol family 31
> Bluetooth: HCI device and connection manager initialized
> Bluetooth: HCI socket layer initialized
> Bluetooth: L2CAP ver 2.8
> Bluetooth: L2CAP socket layer initialized
> Bluetooth: RFCOMM socket layer initialized
> Bluetooth: RFCOMM TTY layer initialized
> Bluetooth: RFCOMM ver 1.8
> eth0: no IPv6 routers present
> agpgart: Found an AGP 3.5 compliant device at 0000:00:00.0.
> agpgart: BIOS bug. AGP bridge claims to only support x4 rateFixing up
> support for x2 & x1
> agpgart: Device is in legacy mode, falling back to 2.x
> agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode
> agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x mode
> eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
> ISO 9660 Extensions: Microsoft Joliet Level 1
> ISOFS: changing to secondary root
> eth0: no IPv6 routers present
>
>
> --
> Be the change you want to see in the world !
--
Be the change you want to see in the world !
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://listman.redhat.com/archives/fedora-list/attachments/20080404/3900dafa/attachment-0001.htm>
More information about the fedora-list
mailing list