SSH in/out extremely slow(PAINFUL) FC2

[Sean Bruno]

Interesting followup on this one.

Ping is returning a time of 15ms with is within tolerance of another
machine sitting on the same physical and logical network.

However, I am not receiving all of the packet responses, eg:
64 bytes from jrea-pdx.metro1.com (192.168.3.26): icmp_seq=1 ttl=61
time=15.4 ms
64 bytes from jrea-pdx.metro1.com (192.168.3.26): icmp_seq=7 ttl=61
time=16.3 ms
64 bytes from jrea-pdx.metro1.com (192.168.3.26): icmp_seq=8 ttl=61
time=16.0 ms
64 bytes from jrea-pdx.metro1.com (192.168.3.26): icmp_seq=10 ttl=61
time=15.5 ms
64 bytes from jrea-pdx.metro1.com (192.168.3.26): icmp_seq=12 ttl=61
time=15.6 ms 

I don't see any errors on my broadcom(tg3) via ifconfig -a:
eth0      Link encap:Ethernet  HWaddr 00:06:5B:F7:9B:DA
          inet addr:192.168.3.26  Bcast:192.168.3.255
	Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:635 errors:0 dropped:0 overruns:0 frame:0
          TX packets:179 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:66438 (64.8 Kb)  TX bytes:24385 (23.8 Kb)
          Interrupt:5
                                                                                   
eth1      Link encap:Ethernet  HWaddr 00:06:5B:F7:9B:DB
          BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)
          Interrupt:4
                                                                                   
lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:1525 errors:0 dropped:0 overruns:0 frame:0
          TX packets:1525 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:1799788 (1.7 Mb)  TX bytes:1799788 (1.7 Mb)


I have booted NON-SMP on this box, to no effect.

I have disabled Hyperthreading and booted non-smp, no change.

Any help would be appreciated...I have been stracing sshd, but nothing
has shown up that would be considered obvious.

On Sat, 2004-04-03 at 14:11, Sean Bruno wrote:
> I just did a fresh install of FC2T2 on a Dell PE 2650(dual P4 2.6Ghz
> with Hyper Threading Turned on).
> 
> I have not done any updates to any packages on the machine.
> 
> The machine is responsive from the console, but it is slow to respond
> when connecting in from a remote box(and connecting out to another
> machine).
> 
> I thought immediately that this was a DNS issue, but the shell after
> logging in is slow as well.
> 
> Running FC1 the machine behaves well and does not exhibit these issues.
> 
> I saw another post about strange behaviour in regards to POP3 and IMAP
> stuff and wondered if this was something similar?
> 
> -- 
> Sean Bruno
> Telecommunications Engineer
> Metro One Telecommunications
> Desk (503)524-1632
> Cell (503)358-6832
> -- 
> Sean Bruno
> Telecommunications Engineer
> Metro One Telecommunications
> Desk (503)524-1632
> Cell (503)358-6832
-- 
Sean Bruno
Telecommunications Engineer
Metro One Telecommunications
Desk (503)524-1632
Cell (503)358-6832