Problem with printer using FC3

luya at jpopmail.com luya at jpopmail.com
Wed Mar 2 20:36:04 UTC 2005 

For some reason, I am unable to print even thought the CUPS services work fine. Here what dmesg said:



 PCI Interrupt Link [LNKB] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI interrupt 0000:00:0f.1[A] -> GSI 11 (level, low) -> IRQ 11
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1
    ide0: BM-DMA at 0xac00-0xac07, BIOS settings: hda:pio, hdb:pio
    ide1: BM-DMA at 0xac08-0xac0f, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
hda: WDC WD1200JB-00GVA0, ATA DISK drive
hdb: Maxtor 6E040L0, ATA DISK drive
elevator: using anticipatory as default io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: CR-48XATE, ATAPI CD/DVD-ROM drive
hdd: IDE DVD-ROM 16X, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 1024KiB
hda: Host Protected Area detected.
        current capacity is 234439535 sectors (120033 MB)
        native  capacity is 234441648 sectors (120034 MB)
hda: Host Protected Area disabled.
hda: 234441648 sectors (120034 MB) w/8192KiB Cache, CHS=16383/255/63, UDMA(100)
hda: cache flushes supported
 hda: hda1 hda2 hda3 < hda5 >
hdb: max request size: 128KiB
hdb: Host Protected Area detected.
        current capacity is 80291135 sectors (41109 MB)
        native  capacity is 80293248 sectors (41110 MB)
hdb: task_no_data_intr: status=0x51 { DriveReady SeekComplete Error }
hdb: task_no_data_intr: error=0x04 { DriveStatusError }
ide: failed opcode was: 0x37
hdb: 80291135 sectors (41109 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(133)
hdb: cache flushes supported
 hdb: hdb1 hdb2
hdc: ATAPI 40X CD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
hdd: ATAPI 48X DVD-ROM drive, 512kB Cache, UDMA(33)
ide-floppy driver 0.99.newide
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard on isa0060/serio0
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
NET: Registered protocol family 2
IP: routing cache hash table of 1024 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 9362)
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
ACPI wakeup devices:
PCI0 USB0 USB1 USB2 USB6 USB7 USB8 USB9 UAR1 ECP1
ACPI: (supports S0 S1 S4 S5)
Freeing unused kernel memory: 160k freed
device-mapper: 4.3.0-ioctl (2004-09-30) initialised: dm-devel at redhat.com
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
SELinux:  Disabled at runtime.
SELinux:  Unregistering netfilter hooks
SCSI subsystem initialized
libata version 1.10 loaded.
sata_via version 1.0
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
ACPI: PCI interrupt 0000:00:0f.0[B] -> GSI 11 (level, low) -> IRQ 11
sata_via(0000:00:0f.0): routed to hard irq line 11
ata1: SATA max UDMA/133 cmd 0x9400 ctl 0x9802 bmdma 0xA400 irq 11
ata2: SATA max UDMA/133 cmd 0x9C00 ctl 0xA002 bmdma 0xA408 irq 11
ata1: no device found (phy stat 00000000)
scsi0 : sata_via
ata2: no device found (phy stat 00000000)
scsi1 : sata_via
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
Linux Tulip driver version 1.1.13 (May 11, 2002)
ACPI: PCI interrupt 0000:00:0a.0[A] -> GSI 11 (level, low) -> IRQ 11
tulip0:  MII transceiver #1 config 3100 status 7869 advertising 05e1.
tulip0:  MII transceiver #2 config 1000 status 786d advertising 05e1.
tulip0:  MII transceiver #3 config 1000 status 786d advertising 05e1.
tulip0:  MII transceiver #4 config 1000 status 786d advertising 05e1.
divert: allocating divert_blk for eth0
eth0: ADMtek Comet rev 17 at e083c000, 00:04:5A:73:D0:B0, IRQ 11.
ACPI: PCI interrupt 0000:00:11.5[C] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:11.5 to 64
ACPI: PCI interrupt 0000:00:10.4[C] -> GSI 11 (level, low) -> IRQ 11
ehci_hcd 0000:00:10.4: EHCI Host Controller
ehci_hcd 0000:00:10.4: irq 11, pci mem 0xeb01a000
ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:10.4: USB 2.0 initialized, EHCI 1.00, driver 26 Oct 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
USB Universal Host Controller Interface driver v2.2
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI interrupt 0000:00:10.0[A] -> GSI 10 (level, low) -> IRQ 10
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: irq 10, io base 0xb000
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:10.1[A] -> GSI 10 (level, low) -> IRQ 10
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: irq 10, io base 0xb400
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:10.2[B] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: irq 11, io base 0xb800
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:10.3[B] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:10.3: UHCI Host Controller
uhci_hcd 0000:00:10.3: irq 11, io base 0xbc00
uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 5
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
usb 2-1: new full speed USB device using uhci_hcd and address 2
hub 2-1:1.0: USB hub found
hub 2-1:1.0: 4 ports detected
usb 2-2: new full speed USB device using uhci_hcd and address 3
usb 4-1: new low speed USB device using uhci_hcd and address 2
input: USB HID v1.00 Joystick [SAITEK P880] on usb-0000:00:10.2-1
NET: Registered protocol family 10
Disabled Privacy Extensions on device c03697c0(lo)
IPv6 over IPv4 tunneling driver
divert: not allocating divert_blk for non-ethernet device sit0
usb 5-1: new low speed USB device using uhci_hcd and address 2
usbhid: probe of 5-1:1.0 failed with error -5
usb 2-1.1: new low speed USB device using uhci_hcd and address 4
input: USB HID v1.10 Mouse [Logitech Optical USB Mouse] on usb-0000:00:10.0-1.1
usb 2-1.4: new full speed USB device using uhci_hcd and address 5
drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 3 if 0 alt 1 proto 2 vid 0x067B pid 0x2305
Initializing USB Mass Storage driver...
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
input: Wacom Graphire2 4x5 on usb-0000:00:10.3-1
usbcore: registered new driver wacom
drivers/usb/input/wacom.c: v1.30:USB Wacom Graphire and Wacom Intuos tablet driver
scsi2 : SCSI emulation for USB Mass Storage devices
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 5
usb-storage: waiting for device to settle before scanning
  Vendor: Generic   Model: USB Storage-SMC   Rev: 0090
  Type:   Direct-Access                      ANSI SCSI revision: 00
  Vendor: Generic   Model: USB Storage-CFC   Rev: 0090
  Type:   Direct-Access                      ANSI SCSI revision: 00
  Vendor: Generic   Model: USB Storage-MMC   Rev: 0090
  Type:   Direct-Access                      ANSI SCSI revision: 00
  Vendor: Generic   Model: USB Storage-MSC   Rev: 0090
  Type:   Direct-Access                      ANSI SCSI revision: 00
usb-storage: device scan complete
Attached scsi removable disk sda at scsi2, channel 0, id 0, lun 0
Attached scsi removable disk sdb at scsi2, channel 0, id 0, lun 1
Attached scsi removable disk sdc at scsi2, channel 0, id 0, lun 2
Attached scsi removable disk sdd at scsi2, channel 0, id 0, lun 3
ACPI: Power Button (FF) [PWRF]
ibm_acpi: ec object not found
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.

It seems the problem is related to PCI. How should I fix it.
-- 
_______________________________________________
Get your free email from http://mymail.jp.popstarmail.org

Powered by Outblaze

More information about the fedora-test-list mailing list