Kudzu segmentation fault. Core5 Test3 upto date as of March 4, 2006
Jason Montleon
monty19 at hotmail.com
Sun Mar 5 06:06:33 UTC 2006
I am suffering the same problem with seg faults using kudzu. My system is a
Dell Inspiron 8000 (PIII 700 Mhz laptop). 'kudzu -s' does not cause a seg
fault. I can file a bug if the other gentleman has not already done so and
add this information along with whatever else you need.
lspci -vv lists the following hardware:
00:00.0 Host bridge: Intel Corporation 82815 815 Chipset Host Bridge and
Memory Controller Hub (rev 02)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Region 0: Memory at e8000000 (32-bit, prefetchable) [size=64M]
Capabilities: [88] Vendor Specific Information
Capabilities: [a0] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64-
HTrans- 64bit- FW- AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW-
Rate=<none>
00:01.0 PCI bridge: Intel Corporation 82815 815 Chipset AGP Bridge (rev 02)
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: fc000000-fdffffff
Prefetchable memory behind bridge: d8000000-e7ffffff
Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR+
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 03)
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=02, subordinate=10, sec-latency=32
I/O behind bridge: 0000d000-0000ffff
Memory behind bridge: f2000000-fbffffff
Prefetchable memory behind bridge: 20000000-23ffffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
00:1f.0 ISA bridge: Intel Corporation 82801BAM ISA Bridge (LPC) (rev 03)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:1f.1 IDE interface: Intel Corporation 82801BAM IDE U100 (rev 03) (prog-if
80 [Master])
Subsystem: Intel Corporation Unknown device 4541
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Region 4: I/O ports at bfa0 [size=16]
00:1f.2 USB Controller: Intel Corporation 82801BA/BAM USB (Hub #1) (rev 03)
(prog-if 00 [UHCI])
Subsystem: Intel Corporation Unknown device 4541
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 10
Region 4: I/O ports at bce0 [size=32]
01:00.0 VGA compatible controller: nVidia Corporation NV17 [GeForce4 440 Go]
(rev a3) (prog-if 00 [VGA])
Subsystem: Dell Unknown device 00a4
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop+ ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (1250ns min, 250ns max)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at fc000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at e0000000 (32-bit, prefetchable) [size=128M]
Region 2: Memory at dff80000 (32-bit, prefetchable) [size=512K]
Expansion ROM at d8000000 [disabled] [size=128K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [44] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA- ITACoh- GART64-
HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW-
Rate=<none>
02:03.0 Multimedia audio controller: ESS Technology ES1983S Maestro-3i PCI
Audio Accelerator (rev 10)
Subsystem: Dell Unknown device 00a4
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 5
Region 0: I/O ports at dc00 [size=256]
Region 1: Memory at f6ffe000 (32-bit, non-prefetchable) [size=8K]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
PME(D0-,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME+
02:06.0 PCI bridge: Actiontec Electronics Inc Mini-PCI bridge (rev 11)
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size 08
Bus: primary=02, secondary=08, subordinate=08, sec-latency=32
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: f8000000-f9ffffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Bridge: PM- B3+
Capabilities: [90] #06 [0000]
02:0f.0 CardBus bridge: Texas Instruments PCI4451 PC card Cardbus Controller
Subsystem: Dell Unknown device 00a4
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 168, Cache Line Size 20
Interrupt: pin A routed to IRQ 10
Region 0: Memory at f6000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=02, secondary=09, subordinate=0c, sec-latency=176
Memory window 0: 20000000-21fff000 (prefetchable)
Memory window 1: f2000000-f3fff000
I/O window 0: 0000d000-0000d0ff
I/O window 1: 0000d400-0000d4ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+
PostWrite+
16-bit legacy interface ports at 0001
02:0f.1 CardBus bridge: Texas Instruments PCI4451 PC card Cardbus Controller
Subsystem: Dell Unknown device 00a4
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 168, Cache Line Size 20
Interrupt: pin A routed to IRQ 10
Region 0: Memory at f6001000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=02, secondary=0d, subordinate=10, sec-latency=176
Memory window 0: 22000000-23fff000 (prefetchable)
Memory window 1: f4000000-f5fff000
I/O window 0: 0000d800-0000d8ff
I/O window 1: 00001000-000010ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+
PostWrite+
16-bit legacy interface ports at 0001
02:0f.2 FireWire (IEEE 1394): Texas Instruments PCI4451 IEEE-1394 Controller
(prog-if 10 [OHCI])
Subsystem: Dell Unknown device 00a4
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (500ns min, 1000ns max), Cache Line Size 08
Interrupt: pin A routed to IRQ 10
Region 0: Memory at f6ffd800 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at f6ff8000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA
PME(D0-,D1-,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
08:04.0 Ethernet controller: Intel Corporation 82557/8/9 [Ethernet Pro 100]
(rev 08)
Subsystem: Actiontec Electronics Inc EtherExpress PRO/100B (TX)
(MiniPCI Ethernet+Modem)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2000ns min, 14000ns max), Cache Line Size 08
Interrupt: pin A routed to IRQ 10
Region 0: Memory at f8fff000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at ecc0 [size=64]
Region 2: Memory at f8e00000 (32-bit, non-prefetchable) [size=1M]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
08:08.0 Communication controller: Agere Systems WinModem 56k (rev 01)
Subsystem: Actiontec Electronics Inc LT WinModem 56k (MiniPCI
Ethernet+Modem)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (63000ns min, 3500ns max)
Interrupt: pin A routed to IRQ 10
Region 0: Memory at f8ffec00 (32-bit, non-prefetchable) [size=256]
Region 1: I/O ports at ecb8 [size=8]
Region 2: I/O ports at e800 [size=256]
Capabilities: [f8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2+ AuxCurrent=0mA
PME(D0-,D1-,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
----- Original Message -----
From: "Jonathan Berry" <berryja at gmail.com>
To: "For testers of Fedora Core development releases"
<fedora-test-list at redhat.com>
Sent: Sunday, March 05, 2006 12:52 PM
Subject: Re: Kudzu segmentation fault. Core5 Test3 upto date as of March
4,2006
> On 3/4/06, Leslie Satenstein <lsatenstein at yahoo.com> wrote:
>> -rwxr-xr-x 1 root root 157444 Feb 28 15:00 kudzu
>
> And yet you refuse to give us any more information regarding your
> system. What hardware do you have? What architecture are you
> running? Are you using Xen? Please be helpful. Just saying that
> something isn't working is not being helpful.
>
> Jonathan
>
> --
> fedora-test-list mailing list
> fedora-test-list at redhat.com
> To unsubscribe:
> https://www.redhat.com/mailman/listinfo/fedora-test-list
>
More information about the fedora-test-list
mailing list