kernel-2.6.27-0.284.rc4.git6.fc10.i686 doesn't boot
Antonio Olivares
olivares14031 at yahoo.com
Sat Aug 30 14:44:32 UTC 2008
--- On Sat, 8/30/08, Antonio M <antonio.montagnani at gmail.com> wrote:
> From: Antonio M <antonio.montagnani at gmail.com>
> Subject: Re: kernel-2.6.27-0.284.rc4.git6.fc10.i686 doesn't boot
> To: "For testers of Fedora Core development releases" <fedora-test-list at redhat.com>
> Date: Saturday, August 30, 2008, 7:03 AM
> 2008/8/29 Andrew Gormanly <a.gormanly at ucl.ac.uk>:
> > More output, the battery failed before I could
> transcribe the top couple of
> > pages though.
> >
> > Andrew Gormanly wrote:
> >>
> >> Same here, 2.6.27-0.287.rc4.git7.fc10.i686 does
> not boot but
> >> 2.6.27-0.244.rc4.git1.fc10.i686 is ok
> >>
> >> Without rhgb but with quiet the messages are:
> >>
> >> stabilized: stat /proc/bus/usb/devices: No such
> file or directory
> >> mount: error mounting /dev/root on /sysroot as
> ext3: No such file or
> >> directory
> >> setuproot: moving /dev failed: No such file or
> directory
> >> setuproot: error mounting /proc: No such file or
> directory
> >> setuproot: error mounting /sys: No such file or
> directory
> >> Mount failed for selinuxfs on /selinux: No such
> file or directory
> >> switchroot: mount failed: No such file or
> directory
> >> sd 0:0:0:0: [sda] Assuming drive cache: write
> through
> >> sd 0:0:0:0: [sda] Assuming drive cache: write
> through
> >>
> >> I'll copy out the full messages from the
> kernel and post when I have them.
> >> This will take ages though.
> >>
> >> Hardware is an Asus Eee PC 4G with rawhide
> installed on an 8GB SDHC card
> >> in the built-in reader. Fedora 9 kernels were ok
> as was
> >> 2.6.27-0.244.rc4.git1.fc10
> >>
> >
> >
> > --
> > Andrew Gormanly
> > London Centre for Nanotechnology
> > University College London
> Tel: 020 7679 3400
> > 17-19 Gordon Street
> Fax: 020 7679 0595
> > London WC1H 0AJ
> a.gormanly AT ucl.ac.uk
> >
> > pci 0000:00:1c.1: IO window: disabled
> > pci 0000:00:1c.1: MEM window: 0xfbf00000-0xfbffffff
> > pci 0000:00:1c.1: PREFETCH window: disabled
> > pci 0000:00:1c.2: PCI bridge, secondary bus 0000:01
> > pci 0000:00:1c.2: IO window: disabled
> > pci 0000:00:1c.2: MEM window: 0xf8000000-0xfbefffff
> > pci 0000:00:1c.2: PREFETCH window:
> 0x000000f0000000-0x000000f6ffffff
> > pci 0000:00:1e.0: PCI bridge, secondary bus 0000:05
> > pci 0000:00:1e.0: IO window: disabled
> > pci 0000:00:1e.0: MEM window: disabled
> > pci 0000:00:1e.0: PREFETCH window: disabled
> > pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low)
> -> IRQ 16
> > pci 0000:00:1c.0: setting latency timer to 64
> > pci 0000:00:1c.1: PCI INT B -> GSI 17 (level, low)
> -> IRQ 17
> > pci 0000:00:1c.1: setting latency timer to 64
> > pci 0000:00:1c.2: PCI INT C -> GSI 18 (level, low)
> -> IRQ 18
> > pci 0000:00:1c.2: setting latency timer to 64
> > pci 0000:00:1e.0: setting latency timer to 64
> > bus: 00 index 0 io port: [0, ffff]
> > bus: 00 index 1 mmio: [0, ffffffffffffffff]
> > bus: 04 index 0 mmio: [0, 0]
> > bus: 04 index 1 mmio: [0, 0]
> > bus: 04 index 2 mmio: [0, 0]
> > bus: 04 index 3 mmio: [0, 0]
> > bus: 03 index 0 mmio: [0, 0]
> > bus: 03 index 1 mmio: [fbf00000, fbffffff]
> > bus: 03 index 2 mmio: [0, 0]
> > bus: 03 index 3 mmio: [0, 0]
> > bus: 01 index 0 mmio: [0, 0]
> > bus: 01 index 1 mmio: [f8000000, fbefffff]
> > bus: 01 index 2 mmio: [f0000000, f6ffffff]
> > bus: 01 index 3 mmio: [0, 0]
> > bus: 05 index 0 mmio: [0, 0]
> > bus: 05 index 1 mmio: [0, 0]
> > bus: 05 index 2 mmio: [0, 0]
> > bus: 05 index 3 io port: [0, ffff]
> > bus: 05 index 4 mmio: [0, ffffffffffffffff]
> > NET: Registered protocol family 2
> > IP route cache hash table entries: 32768 (order: 5,
> 131072 bytes)
> > TCP established has table entriesL 131072 (order: 8,
> 1048576 bytes)
> > TCP bind hash table entriesL 65536 (order: 9, 2359296
> bytes)
> > TCP: Hash tables configured (established 131072 bind
> 65536)
> > TCP reno registered
> > NET: Registered protocol family 1
> > checking if image is initramfs... it is
> > Switched to high resolution on CPU 0
> > debug: unmapping init memory f7d5e000..f7ff0000
> > apm: BIOS version 1.2 Flags 0x03 (Driver version
> 1.16ac)
> > apm: overridden by ACPI
> > audit: initializing netlink socket (disabled)
> > type=2000 audit(1220021774.217:1): initialized
> > highmem bounce pool size: 64 pages
> > HugeTLB registered 4 MB page size, pre-allocated 0
> pages
> > VFS: Disk quotas dquot_6.5.1
> > Dquot-cache hash table entries: 1024 (order 0, 4096
> bytes)
> > msgmni has been set to 1704
> > SELinux: Registering netfilter hooks
> > Block layer SCSI generic (bsg) driver version 0.4
> loaded (major 252)
> > io scheduler noop registered
> > io scheduler anticipatory registered
> > io scheduler deadline registered
> > io scheduler cfg registered (default)
> > pci 0000:00:02.0: Boot video device
> > pci 0000:00:1d.0: uhci_check_and_reset_hc: legsup =
> 0x0f30
> > pci 0000:00:1d.0: Performing full reset
> > pci 0000:00:1d.1: uhci_check_and_reset_hc: legsup =
> 0x0030
> > pci 0000:00:1d.1: Performing full reset
> > pci 0000:00:1d.2: uhci_check_and_reset_hc: legsup =
> 0x0030
> > pci 0000:00:1d.2: Performing full reset
> > pci 0000:00:1d.3: uhci_check_and_reset_hc: legsup =
> 0x0030
> > pci 0000:00:1d.3: Performing full reset
> > pcieport-driver 0000:00:1c.0: setting latency timer to
> 64
> > pcieport-driver 0000:00:1c.0: found MSI capability
> > pci_express 0000:00:1c.0:pcie00: allocate port service
> > pci_express 0000:00:1c.0:pcie02: allocate port service
> > pci_express 0000:00:1c.0:pcie03: allocate port service
> > pcieport-driver 0000:00:1c.1: setting latency timer to
> 64
> > pcieport-driver 0000:00:1c.1: found MSI capability
> > pci_express 0000:00:1c.1:pcie00: allocate port service
> > pci_express 0000:00:1c.1:pcie02: allocate port service
> > pci_express 0000:00:1c.1:pcie03: allocate port service
> > pcieport-driver 0000:00:1c.2: setting latency timer to
> 64
> > pcieport-driver 0000:00:1c.2: found MSI capability
> > pci_express 0000:00:1c.2:pcie00: allocate port service
> > pci_express 0000:00:1c.2:pcie02:allocate port service
> > pci_express 0000:00:1c.2:pcie03:allocate port service
> > pci_hotplug: PCI Hot Plug PCI Core version: 0.5
> > input: Power Button (FF) as
> /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
> > ACPI: Power Button (FF) [PWRF]
> > input: Lid Switch as
> /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input1
> > ACPI: EC: non-query interrupt received, switching to
> interrupt mode
> > ACPI: Lid Switch [LID]
> > input: Sleep Buttion (CM) as
> > /devices/LNXSYSTM:00/device:00/PP0C0E:00/input/input2
> > ACPI: Sleep Button (CM) [SLPB]
> > input: Power Button (CM) as
> > /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input3
> > ACPI: Power Button (CM) [PWRB]
> > ACPI: CPU0 (power statesL C1[C1] C2[C2] C3[C3])
> > processor ACPI0007:00: registered as cooling_device0
> > ACPI: Processor [CPU1] (supports 8 throttling states)
> > thermal LNXTHERM:01: registered as thermal_zone0
> > ACPI: Thermal Zone [TZ00] (35 C)
> > isapnp: Scanning for PnP cards...
> > isapnp: No Plug & Play device found
> > Non-volatile memory driver v1.2
> > Linux agpgart interface v0.103
> > agpgart-intel 0000:00:00.0: Intel 915GM Chipset
> > agpgart-intel 0000:00:00.0: detected 7932K stolen
> memory
> > agpgart-intel 0000:00:00.0: AGP aperture is 256M @
> 0xd0000000
> > Serial: 8250/16550 driver4 ports, IRQ sharing enabled
> > brd: module loaded
> > input: Macintosh mouse button emulation as
> /devices/virtual/input/input4
> > Driver 'sd' needs updating - please use
> bus_type methods
> > ehci_hcd: block sizes: qh 128 qtd 96 itd 160 sitd 96
> > ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level,
> low) -> IRQ 23
> > ehci_hcd 0000:00:1d.7: setting latency timer to 64
> > ehci_hcd 0000:00:1d.7: EHCI Host Controller
> > drivers/usb/core/inode.c: creating file
> 'devices'
> > drivers/usb/core/inode.c: creating file '001'
> > ehci_hcd 0000:00:1d.7: new USB bus registered,
> assigned bus number 1
> > ehci_hcd 0000:00:1d.7: reset hcs_params 0x104208 dbg=1
> cc=4 pcc=2 ordered
> > !ppc ports=8
> > ehci_hcd 0000:00:1d.7: reset hcc_params 6871 thresh 7
> uframes 1024 64 bit
> > addr
> > ehci_hcd 0000:00:1d.7: reset command 080002 (park)=0
> ithresh=8 period=1024
> > Reset HALT
> > ehci_hcd 0000:00:1d.7: debug port 1
> > ehci_hcd 0000:00:1d.7: cache line size of 32 is not
> supported
> > ehci_hcd 0000:00:1d.7: supports USB remote wakeup
> > ehci_hcd 0000:00:1d.7: irq 23, io mem 0xf7eb7c00
> > ehci_hcd 0000:00:1d.7: reset command 080002 (park)=0
> ithresh=8 period=1024
> > Reset HALT
> > ehci_hcd 0000:00:1d.7: init command 010001 (park)=0
> ithresh=1 period-1024
> > RUN
> > ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00,
> driver 10 Dec 2004
> > usb usb1: default language 0x409
> > usb usb1: uevent
> > usb usb1: usb_probe_device
> > usb usb1: configuration #1 chosen from 1 choice
> > usb usb1: adding 1-0:1.0 (config #1, interface 0)
> > usb 1-0:1.0: uevent
> > hub 1-0:1.0: usb_probe_interface
> > hub 1-0:1.0: usb_probe_interface - got id
> > hub 1-0:1.0: USB hub found
> > hub 1-0:1.0: 8 ports detected
> > hub 1-0:1.0: standalone hub
> > hub 1-0:1.0: no power switching (usb 1.0)
> > hub 1-0:1.0: individual port over-current protection
> > hub 1-0:1.0: power on to power good time: 20ms
> > hub 1-0:1.0: local power source is good
> > hub 1-0:1.0: trying to enable port power on
> non-switchable hub
> > ehci_hcd 0000:00:1d.7: GetStatus port 5 status 001803
> POWER sig=j CSC
> > CONNECT
> > hub 1-0:1.0: port 5: status 0501 change 0001
> > hub 1-0:1.0: state 7 ports 8 chg 0020 evt 0000
> > drivers/usb/core/inode.c: creating file '001'
> > hub 1-0:1.0: port 5, status 0501, change 0000, 480
> Mb/s
> > usb usb1: New USB device found, idVendor=1d6b,
> idProduct=0002
> > usb usb1: New USB device strings: Mfr=3, Product=2,
> SerialNumber=1
> > usb usb1: Product: EHCI Host Controller
> > usb usb1: Manufacturer: Linux
> 2.6.27-0.287.rc4.git7.fc10.i686 ehci_hcd
> > usb usb1: SerialNumber: 0000:00:1d.7
> > ohci_hcd: 2006 August 04 USB 1.1 'Open' Host
> Controller (OHCI) Driver
> > ohci_hcd: block sizes: ed 64 td 64
> > USB Universal Host Controller Interface driver v3.0
> > uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level,
> low) -> IRQ 23
> > uhci_hcd 0000:00:1d.0: setting latency timer to 64
> > uhci_hcd 0000:00:1d.0: UHCI Host Controller
> > drivers/usb/core/inode.c: creating file '002'
> > uhci_hcd 0000:00:1d.0: new USB bus registered,
> assigned bus number 2
> > uhci_hcd 0000:00:1d.0: detected 2 ports
> > uhci_hcd 0000:00:1d.0: uhci_check_and_reset_hc: cmd =
> 0x0000
> > uhci_hcd 0000:00:1d.0: Performing full reset
> > uhci_hcd 0000:00:1d.0: supports USB remote wakeup
> > uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000e400
> > usb usb3: default language 0x409
> > usb usb3: uevent
> > usb usb3: usb_probe_device
> > usb usb3: configuration #1 chosen from 1 choice
> > usb usb3: adding 2-0:1.0 (config #1, interface 0)
> > usb 2-0:1.0: uevent
> > hub 2-0:1.0: usb_probe_interface
> > hub 2-0:1.0: usb_probe_interface - got id
> > hub 2-0:1.0: USB hub found
> > hub 2-0:1.0: 2 ports detected
> > hub 2-0:1.0: standalone hub
> > hub 2-0:1.0: no power switching (usb 1.0)
> > hub 2-0:1.0: individual port over-current protection
> > hub 2-0:1.0: power on to power good time: 2ms
> > hub 2-0:1.0: local power source is good
> > hub 2-0:1.0: trying to enable port power on
> non-switchable hub
> > ehci_hcd 0000:00:1d.7: port 5 high speed
> > ehci_hcd 0000:00:1d.7: GetStatus port 5 status 001005
> POWER sig=se0 PE
> > CONNECT
> > usb 1-5: new high speed USB device using ehci_hcd and
> address 2
> > drivers/usb/core/inode.c: creating file '001'
> > usb usb2: New USB device found, idVendor=1d6b,
> idProduct=0001
> > usb usb2: New USB device strings: Mfr=3, Product=2,
> SerialNumber=1
> > usb usb2: Product: UHCI Host Controller
> > usb usb2: Manufacturer: Linux
> 2.6.27-0.287.rc4.git7.fc10.i686 uhci_hcd
> > usb usb2: SerialNumber: 0000:00:1d.0
> > uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level,
> low) -> IRQ 19
> > uhci_hcd 0000:00:1d.1: setting latency timer to 64
> > uhci_hcd 0000:00:1d.1: UHCI Host Controller
> > drivers/usb/core/inode.c: creating file '003'
> > uhci_hcd 0000:00:1d.1: new USB bus registered,
> assigned bus number 3
> > uhci_hcd 0000:00:1d.1: detected 2 ports
> > uhci_hcd 0000:00:1d.1: uhci_check_and_reset_hc: cmd =
> 0x0000
> > uhci_hcd 0000:00:1d.1: Performing full reset
> > uhci_hcd 0000:00:1d.1: supports USB remote wakeup
> > uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000e480
> > usb usb3: default language 0x409
> > usb usb3: uevent
> > usb usb3: usb_probe_device
> > usb usb3: configuration #1 chosen from 1 choice
> > usb usb3: adding 3-0:1.0 (config #1, interface 0)
> > usb 3-0:1.0: uevent
> > hub 3-0:1.0: usb_probe_interface
> > hub 3-0:1.0: usb_probe_interface - got id
> > hub 3-0:1.0: USB hub found
> > hub 3-0:1.0: 2 ports detected
> > hub 3-0:1.0: standalone hub
> > hub 3-0:1.0: no power switching (usb 1.0)
> > hub 3-0:1.0: individual port over-current protection
> > hub 3-0:1.0: power on to power good time: 2ms
> > hub 3-0:1.0: local power source is good
> > hub 3-0:1.0: trying to enable port power on
> non-switchable hub
> > ehci_hcd 0000:00:1d.7: port 5 high speed
> > ehci_hcd 0000:00:1d.7: GetStatus port 5 status 001005
> POWER sig=se0 PE
> > CONNECT
> > usb 1-5: default language 0x0409
> > usb 1-5: uevent
> > usb 1-5: usb_probe_device
> > usb 1-5: configuration #1 chosen from 1 choice
> > usb 1-5: adding 1-5:1.0 (config #1, interface 0)
> > usb 1-5:1.0: uevent
> > drivers/usb/core/inode.c: creating file '002'
> > usb 1-5: New USB device found, idVendor=0951,
> idProduct=1606
> > usb 1-5: New USB device strings: Mfr=1, Product=2,
> SerialNumber=4
> > usb 1-5: Product: UB6225
> > usb 1-5: Manufacturer: ENE
> > usb 1-5: SerialNumber: 146030377350
> > hub 2-0:1.0: state 7 ports 2 chg 0000 evt 0000
> > hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
> > drivers/usb/core/inode.c: creating file '001'
> > usb usb3: New USB device found, idVendor=1d6b,
> idProduct=0001
> > usb usb3: New USB device strings: Mfr=3, Product=2,
> SerialNumber=1
> > usb usb3: Product: UHCI Host Controller
> > usb usb3: Manufacturer: Linux
> 2.6.27-0.287.rc4.git7.fc10.i686 uhci_hcd
> > usb usb3: SerialNumber: 0000:00:1d.1
> > uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level,
> low) -> IRQ 18
> > uhci_hcd 0000:00:1d.2: setting latency timer to 64
> > uhci_hcd 0000:00:1d.2: UHCI Host Controller
> > drivers/usb/core/inode.c: creating file '004'
> > uhci_hcd 0000:00:1d.2: new USB bus registered,
> assigned bus number 4
> > uhci_hcd 0000:00:1d.2: detected 2 ports
> > uhci_hcd 0000:00:1d.2: uhci_check_and_reset_hc: cmd =
> 0x0000
> > uhci_hcd 0000:00:1d.2: Performing full reset
> > uhci_hcd 0000:00:1d.2: supports USB remote wakeup
> > uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000e800
> > usb usb4: default language 0x409
> > usb usb4: uevent
> > usb usb4: usb_probe_device
> > usb usb4: configuration #1 chosen from 1 choice
> > usb usb4: adding 4-0:1.0 (config #1, interface 0)
> > usb 4-0:1.0: uevent
> > usb 4-0:1.0: usb_probe_interface
> > usb 4-0:1.0: usb_probe_interface - got id
> > usb 4-0:1.0: USB hub found
> > usb 4-0:1.0: 2 ports detected
> > usb 4-0:1.0: standalone hub
> > usb 4-0:1.0: no power switching (usb 1.0)
> > usb 4-0:1.0: individual port over-current protection
> > usb 4-0:1.0: power on to power good time: 2ms
> > usb 4-0:1.0: local power source is good
> > usb 4-0:1.0: trying to enable port power on
> non-switchable hub
> > uhci_hcd 0000:00:1d.2: port 1 portsc 0082,00
> > usb 4-0:1.0: state 7 ports 2 chg 0000 evt 0000
> > drivers/usb/core/inode.c: creating file '001'
> > usb usb4: New USB device found, idVendor=1d6b,
> idProduct=0001
> > usb usb4: New USB device strings: Mfr=3, Product=2,
> SerialNumber=1
> > usb usb4: Product: UHCI Host Controller
> > usb usb4: Manufacturer: Linux
> 2.6.27-0.287.rc4.git7.fc10.i686 uhci_hcd
> > usb usb4: SerialNumber: 0000:00:1d.2
> > uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level,
> low) -> IRQ 16
> > uhci_hcd 0000:00:1d.3: setting latency timer to 64
> > uhci_hcd 0000:00:1d.3: UHCI Host Controller
> > drivers/usb/core/inode.c: creating file '005'
> > uhci_hcd 0000:00:1d.3: new USB bus registered,
> assigned bus number 5
> > uhci_hcd 0000:00:1d.3: detected 2 ports
> > uhci_hcd 0000:00:1d.3: uhci_check_and_reset_hc: cmd =
> 0x0000
> > uhci_hcd 0000:00:1d.3: Performing full reset
> > uhci_hcd 0000:00:1d.3: supports USB remote wakeup
> > uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000e880
> > usb usb5: default language 0x409
> > usb usb5: uevent
> > usb usb5: usb_probe_device
> > usb usb5: configuration #1 chosen from 1 choice
> > usb usb5: adding 5-0:1.0 (config #1, interface 0)
> > usb 5-0:1.0: uevent
> > usb 5-0:1.0: usb_probe_interface
> > usb 5-0:1.0: usb_probe_interface - got id
> > usb 5-0:1.0: USB hub found
> > usb 5-0:1.0: 2 ports detected
> > hub 5-0:1.0: standalone hub
> > hub 5-0:1.0: no power switching (usb 1.0)
> > hub 5-0:1.0: individual port over-current protection
> > hub 5-0:1.0: power on to power good time: 2ms
> > hub 5-0:1.0: local power source is good
> > hub 5-0:1.0: trying to enable port power on
> non-switchable hub
> > hub 5-0:1.0: state 7 ports 2 chg 0000 evt 0000
> > drivers/usb/core/inode.c: creating file '001'
> > usb usb5: New USB device found, idVendor=1d6b,
> idProduct=0001
> > usb usb5: New USB device strings: Mfr=3, Product=2,
> SerialNumber=1
> > usb usb5: Product: UHCI Host Controller
> > usb usb5: Manufacturer: Linux
> 2.6.27-0.287.rc4.git7.fc10.i686 uhci_hcd
> > usb usb5: SerialNumber: 0000:00:1d.3
> > PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at
> 0x60,0x64 irq 1,12
> > serio: i8042 KBD port at 0x60,0x64 irq 1
> > Setting up hotplug.rt at 0x60,0x64 irq 12
> > Creating block device nodes.on for all mice
> > Loading ext3 module core: registered rtc_cmos as rtc0
> > usb usb2: suspend_rh (auto-stop)et irqs
> > usb usb3: suspend_rh (auto-stop)
> > Loading usb-storage modulenu
> > Initializing USB Mass Storage driver...r hiddev
> > usb-storage 1-5:1.0: usb_probe_interface usbhid
> > usb-storage 1-5:1.0: usb_probe_interface - got id
> > scsi0 : SCSI emulation for USB Mass Storage devices
> > usbcore: registered new interface driver usb-storage
> > USB Mass Storage support registered.
> > Waiting for driver initialization.
> > stabilized: stat /proc/bus/usb/devices: No such file
> or directory
> > Creating root device. :941
> > usb-storage: device found at 207f9000..c096d000
> > usb-storage: waiting for device to settle before
> scaning
> > Mounting root filesystem.2 keyboard as
> > /devices/platform/i8042/serio/input/inpu
> > mount: error mounting /dev/root on /sysroot as ext3:
> No such file or
> > directory
> > Setting up other filesystems.
> > setuproot: moving /dev failed: No such file or
> directory
> > setuproot: error mounting /proc: No such file or
> directory
> > setuproot: error mounting /sys: No such file or
> directory
> > Mount failed for selinuxfs on /selinux: No such file
> or directory
> > Switching to new root and running init.
> > switchroot: mount failed: No such file or directory
> > Booting has failed.
> > usb usb4: suspend_rh (auto-stop)
> > Synaptics Touchpad, model: 1, fw: 6.5, id: 0x1c0b1,
> caps: 0xa04751/0xa00000
> > input: SynPS/2 Synaptics TouchPad as
> > /devices/platform/i8042/serio1/input/input6
> > usb usb5: suspend_rh (auto-stop)
> > hub 2-0:1.0: hub_suspend
> > usb usb2: bus auto-suspend
> > usb usb2: suspend_rh
> > hub 3-0:1.0: hub_suspend
> > usb usb3: bus auto-suspend
> > usb usb3: suspend_rh
> > hub 4-0:1.0: hub_suspend
> > usb usb4: bus auto-suspend
> > usb usb4: suspend_rh
> > hub 5-0:1.0: hub_suspend
> > usb usb5: bus auto-suspend
> > usb usb5: suspend_rh
> > usb-storage: device scan complete
> > scsi 0:0:0:0: Direct-Access USB2.0 CardReader
> SD0 0100 PQ: 0 ANSI: 0
> > sd 0:0:0:0: [sda] 15954944 512-byte hardware sectors
> (8169 MB)
> > sd 0:0:0:0: [sda] Write Protect is off
> > sd 0:0:0:0: [sda] Mode Sense: 03 00 00 00
> > sd 0:0:0:0: Assuming drive cache: write through
> > sd 0:0:0:0: 15954944 512-byte hardware sectors (8169
> MB)
> > sd 0:0:0:0: [sda] Write Protect is off
> > sd 0:0:0:0: [sda] Mode Sense: 03 00 00 00
> > sd 0:0:0:0: Assuming drive cache: write through
> > sda: sda1 sda2
> > sd 0:0:0:0: [sda] Attached SCSI removable disk
> > sd 0:0:0:0: Attached SCSI generic sg0 type 0
> > scsi_scan_0 used greatest stack depth: 1928 bytes left
> >
> > --
> > fedora-test-list mailing list
> > fedora-test-list at redhat.com
> > To unsubscribe:
> >
> https://www.redhat.com/mailman/listinfo/fedora-test-list
> >
> also 287 has exactly same problem.....that means that
> nobody read
> this thread :-( and I spent some time to install and
> de-install the
> kernel.
It happens at some point or another. I installed the 284 kernel and it worked for me. However I even installed the 290 kernel and it worked! Things like this happen to us at one point or another. I have also needed to remove several kernels that were not working for me :)
BTW, thank you for bringing up the printing problem. I am having problems printing as well. We are here and we do read the thread(s). Sorry I could not have provided advice since those kernels booted for me :(
>
>
> --
> Antonio Montagnani
> Skype : antoniomontag
>
> --
Regards,
Antonio
More information about the fedora-test-list
mailing list