[Date Prev][Date Next]   [Thread Prev][Thread Next]   [Thread Index] [Date Index] [Author Index]

RE: RHEL3U8 pxe install: no driver for Broadcom NIC?



Not sure why you are having this issue then.  I would go back to Sun and tell them you need a driver disk (both IBM and HP supply driver disks in this scenario).  You then simply load the driver during the build: dd=http://path_to/disk.img
 
Chip


From: kickstart-list-bounces redhat com [mailto:kickstart-list-bounces redhat com] On Behalf Of Doug Rylaarsdam
Sent: Friday, April 06, 2007 12:24 PM
To: 'Discussion list about Kickstart'
Subject: RE: RHEL3U8 pxe install: no driver for Broadcom NIC?

Yes, I’m using the same setup as my RHEL3U3 kickstarts. I’m using the same DHCP and tftp server. I’ve added the RHEL3U8 distribution to the kickstart server, and added a target in the pxelinux configuration with the vmlinuz kernel and initrd.img from the U8 distribution. For the network setup, the kickstart server uses a second NIC to support the kickstart clients. I simply connect the client machine directly to an unmanaged layer2 switch (Linksys EF4124), which is where the second interface on the kickstart server is also located.

 

Doug

 


From: Shabazian, Chip [mailto:Chip Shabazian bankofamerica com]
Sent: Friday, April 06, 2007 2:01 PM
To: Discussion list about Kickstart
Subject: RE: RHEL3U8 pxe install: no driver for Broadcom NIC?

 

Are you on the same switch and subnet that you have previously had good kickstarts from?  This is USUALLY an error related to portfast and Cisco switches.  The fact that the install works fine using the included driver when you build from CD adds to my suspicion that this is network, not NIC related.

 

Chip

 


From: kickstart-list-bounces redhat com [mailto:kickstart-list-bounces redhat com] On Behalf Of Doug Rylaarsdam
Sent: Friday, April 06, 2007 11:36 AM
To: kickstart-list redhat com
Subject: RHEL3U8 pxe install: no driver for Broadcom NIC?

Hi,

 

I am having a NIC driver problem with pxe kickstart of RHEL3 update 8 on some new hardware (Sun X2100 M2).

 

The vendor documentation indicates that RHEL3 U7 or later has compatible drivers for this server. When I install RHEL3 U8 from CD, it works ok. When I attempt a pxe kickstart, it appears that the NIC driver is not compatible. I get the “no network device in choosenetworkinterface” message. I have been kickstarting RHEL3U3 for some time (on older hardware), so I think in general that I have a working pxe kickstart server environment.

 

The NIC is a Broadcom device. The server vendor supplies the Broadcom drivers, but not in binary form for RHEL3 U8. Based on my limited understanding of how this works, I would need to build the tg3 driver from source against the boot kernel (2.4.21-47.ELBOOT) if I want to use the Broadcom NIC for a network install. Then I would need to add the new driver to the initrd image, or make it available as a driver disk. When I look inside the initrd image, the tg3.o driver is definitely not identical to the tg3.o driver from the CD install, although that doesn’t prove that the tg3 driver available during kickstart is incompatible with my hardware.

 

Does it seem likely that RHEL3 U8 would contain a compatible driver for the Broadcom NIC for the 2.4.21-47.EL kernel, but that the driver for the boot kernel is not compatible? That seemed odd to me, so I thought I would ask the question before proceeding with building the driver from source, somewhat unfamiliar territory for me (especially building for boot kernels). Or might there be another cause to this problem?

 

Thanks,

 

Doug


[Date Prev][Date Next]   [Thread Prev][Thread Next]   [Thread Index] [Date Index] [Author Index]