Crete Volgroup from anaconda ks using the whole disk

[Francisco Javier Lloreda Sanchez]

Thanks MAtthew for your answer but this is exactly what I'm triying to 
avoid... :)

I would like to have the equivalent to :
     pvcreate /dev/vdb
     vgcreate test /dev/vdb
     lvcreate -n lv_test -L 10G test

So at the end of the installation I would have a vg over no partition 
(not the whole disk but over the disk device).

Thanks

--
Francisco Javier Lloreda
Red Hat Consultant
( RHCA , RHCDS , RHCVA ) #110-651-718
flloreda at redhat.com
Mobile: 0034 600 48 39 73

c/ Jose Bardasano Baos, No. 9
Edificio Gorbea 3
Madrid, 28016 SPAIN

El 18/01/13 18:37, Conley, Matthew M CTR JXSNM, JSORD escribió:
> Like this?
>
> #Clean install, remove all exisiting partitions
> clearpart --all --initlabel
>
> #create partitions for boot and swap
> part /boot 	--fstype ext3	--size=100	--ondisk=sda
>
> #This is a cheat to allow the partition for the logical volume to grow and consume the rest of the disk
>
> part pv.0  	--size=1 --encrypted --passphrase=PASSPHRASE --grow --ondisk=sda
>
> part pv.1  	--size=1 --encrypted --passphrase=PASSPHRASE --grow --ondisk=sdb
>
> #create volume group vg0
> #then create logical volumes for root, home, and log
> volgroup vg0 pv.0
> logvol   /		--fstype=ext4   --name=lv_root	--vgname=vg0	--size=10000
> logvol  swap  		--fstype=swap	--name=lv_swap	--vgname=vg0	--size=4096
> logvol	 /home		--fstype=ext4	--name=lv_home	--vgname=vg0	--size=1000	--grow
> logvol	 /var/log	--fstype=ext4	--name=lv_log	--vgname=vg0	--size=5000
>
> volgroup vg1 pv.1
> logvol	 /var/lib/mysql	--fstype=ext4	--name=lv_lib	--vgname=vg1	--size=85000
> logvol	 /var/files	--fstype=ext4	--name=lv_data	--vgname=vg1	--size=20000	--grow
>
>
> Regards
> Matthew M. Conley Linux+, A+, Net+, LPIC1
> Systems Engineer
> Next Wave Systems
> 912.398.6704
>
>
>
> -----Original Message-----
> From: Francisco Javier Lloreda Sanchez [mailto:flloreda at redhat.com]
> Sent: Fri 1/18/2013 6:31 AM
> To: kickstart-list at redhat.com
> Subject: Crete Volgroup from anaconda ks using the whole disk
>   
> Hi all,
>
> Has someone managed to create a volume group from a kickstart that uses
> the whole disk and not a partition ?
>
> I tried to create the pv, vg and lv from a pre script and then use the
> --useexisting flag for logvol and anaconda complains about the vg is not
> created and I guess is because I didn't use the volgroup command in the
> partitioning section.
> If I use the volgroup tag with --useexisting in the partitioning section
> I'm forced to use a list of partitions that is what I'm triying to
> avoid....
>
> So any suggestions?
>
> Thanks
>