[libvirt] [PATCH] qemu: add port check for iscsi host when disk type is network
Shanzhi Yu
shyu at redhat.com
Thu Nov 13 10:30:40 UTC 2014
On 11/13/2014 06:21 PM, Peter Krempa wrote:
> On 11/13/14 11:17, Shanzhi Yu wrote:
>> On 11/13/2014 05:42 PM, Peter Krempa wrote:
>>> On 11/13/14 10:28, Shanzhi Yu wrote:
>>>> For network type disk, host port is not checked when source protocol is
>>>> iscsi, so the error is not sure when with invalid port. If pass -1 to
>>>> port
>>>> the error will be
>>>> error: Failed to start domain rh6-i
>>>> error: An error occurred, but the cause is unknown
>>>>
>>>> Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1163553
>>>> Signed-off-by: Shanzhi Yu <shyu at redhat.com>
>>>> ---
>>>> src/qemu/qemu_command.c | 6 ++++++
>>>> 1 file changed, 6 insertions(+)
>>>>
>>>> diff --git a/src/qemu/qemu_command.c b/src/qemu/qemu_command.c
>>>> index f674ba9..f806225 100644
>>>> --- a/src/qemu/qemu_command.c
>>>> +++ b/src/qemu/qemu_command.c
>>>> @@ -3016,6 +3016,12 @@ qemuBuildNetworkDriveURI(int protocol,
>>>> case VIR_STORAGE_NET_PROTOCOL_FTPS:
>>>> case VIR_STORAGE_NET_PROTOCOL_TFTP:
>>>> case VIR_STORAGE_NET_PROTOCOL_ISCSI:
>>>> + if (STRNEQ_NULLABLE(hosts->port,"3260")) {
>>>> + virReportError(VIR_ERR_INTERNAL_ERROR, "%s",
>>>> + _("expected port for iscsi host
>>>> should be 3260"));
>>>> + goto cleanup;
>>>> + }
>>> Um? this would forbid to use any other port than 3260 for any of the
>>> protocols stated above. That doesn't make sense neither for iSCSI nor
>>> for the other ones.
>>>
>>> The code should make sure that the port is in range <0,65536> and don't
>>> force to use a certain port. Ohterwise we wouldn't need a port field.
>> How about make a check for every protocols above, eg FTP, HTTP. As
>> known, different protocol use certain port, if just make sure
> They use certain ports as a default. That doesn't mean the admin can't
> configure to run the service at a different port.
Yes, I see.
>
>> the port is in range <0.65535>, error info may be like
>>
>> error: Failed to start domain rh6-i
>> error: internal error: process exited while connecting to monitor:
>> 2014-11-13T10:06:57.112170Z qemu-system-x86_64: -drive
>> file=ftp://10.66.6.111:100/mnt/nfs/rhel6.img,if=none,id=drive-virtio-disk0,format=raw,cache=none:
>> could not open disk image ftp://10.66.6.111:100/mnt/nfs/rhel6.img: curl
>> block device does not support writes
> You didn't understand the error message apparently. The message says
> that the FTP backend in qemu is supported only with read-only disks, not
> that port "100" is invalid.
I misunderstand the error info. Thanks for explanation
>
> Peter
>
>
--
Regards
shyu
More information about the libvir-list
mailing list