[libvirt-users] attaching storage pool error
John Ferlan
jferlan at redhat.com
Wed Sep 7 13:00:51 UTC 2016
On 09/03/2016 01:00 PM, Johan Kragsterman wrote:
>
> Hi again!
>
>
> Need to add here, since I been investigating a bit further, that it seems to be possible to add an NPIV vhba to the guest, using vdsm hooks. I've seen the reference to "host device assignments", which Dan pointed me too, but I didn't really understand the meaning of it at that moment.
>
> It would be interesting to hear from someone that have been doing it, how it would look like in the xml dump.
>
> From libvirt documentation you can add this:
>
>
> <devices>
> <hostdev mode='subsystem' type='scsi' sgio='filtered' rawio='yes'>
> <source>
> <adapter name='scsi_host0'/>
> <address bus='0' target='0' unit='0'/>
> </source>
> <readonly/>
> <address type='drive' controller='0' bus='0' target='0' unit='0'/>
> </hostdev>
> </devices>
>
>
> Question is what will happen if I add this, and nothing more? Using the scsi_host belonging to my vhba. I am sure it will need some more than this?
>
As I pointed out to you in the other response, this is on my list of
things to look at...
> So how would this be combined with perhaps a virtio-scsi controller, with an NPIV pool, if needed, etc? What would be a working configuration?
>
The <address> has a "controller" field that is the "index" of whichever
scsi controller you want to use, e.g.:
<controller type='scsi' index='0' model='virtio-scsi'>
...
</controller>
> Questions to ask is like:
>
> Would the NPIV vhba survive a reboot without an NPIV pool config?
And that's the issue with using vHBA directly - the 'scsi_hostM' changes
between reboots. The good news is that you can hotplug a scsi_hostM...
> Would the guest vm bring up the vhba and make the lun's accessible for the vm firmware to be able to read the data from the disk, and to boot from it?
Well that would be my assumption... But I haven't configured/used it
this way during my limited testing.
> Would it need to be some disks, volumes or LUN's configured in the source path here? If so, it would not be optimal, since you would like to be able to have a dynamic LUN provisioning. If I provision a LUN to a guest, I would like the LUN to have the number I give it in the scsi target appliance, so that it boots from LUN0, and number the LUN's according to the target numbering.
>
> So, any one that can continue the discussion here?
I think you're the first one to take this option, so you're blazing
through new ground here. Obviously from a libvirt side I'm interested,
but it's not my 100% task either. There's also one other individual on
this list that's dabbled in vHBA/NPIV recently - Nitesh Konkar. There's
a posting on libvir-list that has some details of issues found with the
/dev/disk/by-id/:
http://www.redhat.com/archives/libvir-list/2016-July/msg00524.html
John
>
> Regards Johan
>
>
>
>
> -----libvirt-users-bounces at redhat.com skrev: -----
> Till: John Ferlan <jferlan at redhat.com>
> Från: Johan Kragsterman
> Sänt av: libvirt-users-bounces at redhat.com
> Datum: 2016-09-03 13:16
> Kopia: libvirt-users at redhat.com, Yuan Dan <dyuan at redhat.com>
> Ärende: [libvirt-users] Ang: Ang: Re: Ang: Ang: Re: Ang: Re: attaching storage pool error
>
> Hi!
>
>
> Report from my multipath tests today.
>
>
> My test virtual machine, that runs from an NPIV pool, is not able to use multipath.
>
> When I pulled the cable from one of the targets, it crashed.
>
> But, strangely, it could boot up again on that other path, that it just crashed on.
>
> That tells me it can use both paths, and is not limited to one of them only, but because the multipath layer isn't there, it can not survive a path failure, but can come up again on a reboot.
>
> The question is, WHY doesn't an NPIV pool support multipath? It is sort of the idea behind FC to be redundant and to always have multiple paths to failover to. Why was the NPIV pool designed like this?
>
> If we could use the underlying devices and pass them directly to the guest, then we could implement multipath in the guest.
>
> But I sort of lean to that not use the NPIV anymore, since it only seems to complicate things. In VmWare they can attach the NPIV directly to the guest, which means that the NPIV, and whith that the LUN's are easily transfered across the SAN hosts. Here, with libvirt/qemu/kvm, we can not attach an NPIV to the guest, which sort of makes the whole idea fall. Especially if this is the case, that there is no multipath support. Better then to map the LUN's directly to the host, and use the multipath devices for the guests.
>
> If anyone else has opinions on this, or ideas that are better than mine, I would very much like to hear them.
>
> Regards Johan
>
>
>
>
> -----libvirt-users-bounces at redhat.com skrev: -----
> Till: John Ferlan <jferlan at redhat.com>
> Från: Johan Kragsterman
> Sänt av: libvirt-users-bounces at redhat.com
> Datum: 2016-09-03 08:36
> Kopia: libvirt-users at redhat.com, Yuan Dan <dyuan at redhat.com>
> Ärende: [libvirt-users] Ang: Re: Ang: Ang: Re: Ang: Re: attaching storage pool error
>
> Hi, John, and thank you!
>
> This was a very thorough and welcome response, I was wondering where all the storage guys were...
>
> I will get back to you with more details later, specifically about multipath, since this needs to be investigated thoroughly.
>
> I have, with trial and error method, during the elapsed time, been able to attach the NPIV pool LUN to a virtio-scsi controller, and it seems it already uses multipath, when I look at the volumes in the host.
>
> It seems for me a little bit confusing with this multipath pool procedure, since an NPIV vhba by nature always is multipath. I will do a very simple test later today, the best test there is: Just pulling a cable, first from one of the FC targets, and put it back again, and then do the same with the other one. This will give me the answer if it runs on multipath or not.
>
> The considerations I got was, whether I would implement multipath on the guest or on the host, and I don't know which I would prefer. Simplicity is always to prefer, so if it is working fine on the host, I guess I'd prefer that.
>
> Get back to you later...
>
> /Johan
>
>
> -----John Ferlan <jferlan at redhat.com> skrev: -----
> Till: Johan Kragsterman <johan.kragsterman at capvert.se>, Yuan Dan <dyuan at redhat.com>
> Från: John Ferlan <jferlan at redhat.com>
> Datum: 2016-09-02 20:51
> Kopia: libvirt-users at redhat.com
> Ärende: Re: [libvirt-users] Ang: Ang: Re: Ang: Re: attaching storage pool error
>
>
> On 08/24/2016 06:31 AM, Johan Kragsterman wrote:
>>
>> Hi again!
>>
>
> I saw this last week while I was at KVM Forum, but just haven't had the
> time until now to start thinking about this stuff again ... as you point
> out with your questions and replies - NPIV/vHBA is tricky and
> complicated... I always have try to "clear the decks" of anything else
> before trying to page how this all works back into the frontal cortex.
> Once done, I quickly do a page flush.
>
> It was also a bit confusing with respect to how the responses have been
> threaded - so I just took the most recent one and started there.
>
>> -----libvirt-users-bounces at redhat.com skrev: -----
>> Till: Yuan Dan <dyuan at redhat.com>
>> Från: Johan Kragsterman
>> Sänt av: libvirt-users-bounces at redhat.com
>> Datum: 2016-08-24 07:52
>> Kopia: libvirt-users at redhat.com
>> Ärende: [libvirt-users] Ang: Re: Ang: Re: attaching storage pool error
>>
>> Hi and thanks for your important input,Dan!
>>
>>
>>>>
>>>>
>>>> System centos7, system default libvirt version.
>>>>
>>>> I've succeeded to create an npiv storage pool, which I could start without
>>>> problems. Though I couldn't attach it to the vm, it throwed errors when
>>>> trying. I want to boot from it, so I need it working from start. I read one
>>>> of Daniel Berrange's old(2010) blogs about attaching an iScsi pool, and
>>>> draw
>>>> my conclusions from that. Other documentation I haven't found. Someone can
>>>> point me to a more recent documentation of this?
>>>>
>>>> Are there other mailing list in the libvirt/KVM communities that are more
>>>> focused on storage? I'd like to know about these, if so, since I'm a
>>>> storage
>>>> guy, and fiddle around a lot with these things...
>>>>
>>>> There are quite a few things I'd like to know about, that I doubt this list
>>>> cares about, or have knowledge about, like multipath devices/pools,
>>>> virtio-scsi in combination with npiv-storagepool, etc.
>>>>
>>>> So anyone that can point me further....?
>>>
>>> http://libvirt.org/formatstorage.html
>>> https://access.redhat.com/documentation/en-US/Red_Hat_Enterprise_Linux/7/html/Virtualization_Deployment_and_Administration_Guide/sect-NPIV_storage.html
>>>
>
> The Red Hat documentation is most up-to-date - it was sourced (more or
> less) from:
>
> http://wiki.libvirt.org/page/NPIV_in_libvirt
>
> There's some old stuff in there and probably needs a cleanse to provide
> all the "supported" options.
>
>
>>> Hope it can help you to get start with it.
>>>
>>>
>>> Unfortunatly I have already gone through these documents, several times as
>>> well, but these are only about the creation of storage pools, not how you
>>> attach them to the guest.
>>
>> If the pool is ready, here are kinds of examples http://libvirt.org/formatdomain.html#elementsDisks
>>
>> you can use it in guest like this:
>> <disk type='volume' device='disk'>
>> <driver name='qemu' type='raw'/>
>> <source pool='iscsi-pool' volume='unit:0:0:1' mode='host'/>
>> <auth username='myuser'>
>> <secret type='iscsi' usage='libvirtiscsi'/>
>> </auth>
>> <target dev='vdb' bus='virtio'/>
>> </disk>
>>
>
> This is an 'iscsi' pool format, but something similar can be crafted for
> the 'scsi' pool used for fc_host devices.
>
>>
>>
>> As I described above, I created an npiv pool for my FC backend. I'd also like to get scsi pass through, which seems to be possible only if I use "device=lun". Can I NOT use "device=lun", and then obviously NOT get "scsi pass through", if I use an npiv storage pool? Is the only way to get "scsi pass through" to NOT use a storage pool, but instead use the host lun's?
>>
>
> So for the purposes of taking the right steps, I assume you used 'virsh
> nodedev-list --cap vports' in order to find FC capable scsi_host#'s.
>
> Then you created your vHBA based on the FC capable fc_host, using XML
> such as:
>
> <device>
> <parent>scsi_hostN</parent>
> <capability type='scsi_host'>
> <capability type='fc_host'>
> </capability>
> </capability>
> </device>
>
> where scsi_hostN and 'N' in particular is the FC capable fc_host
>
> Then creation of the node device :
>
> #virsh nodedev-create vhba.xml
> Node device scsi_hostM created from vhba.xml
>
> where 'M' is whatever the next available scsi_host# is on your host.
>
> If you 'virsh nodedev-dumpxml scsi_hostM' you'll see the wwnn/wwpn details.
>
> You can then create a vHBA scsi pool from that in order to ensure the
> persistence of the vHBA. Although it's not required - the vHBA scsi
> pool just allows you to provide a source pool and volume by unit # for
> your guest rather than having to edit guests between host reboots or
> other such conditions which cause
>>
>> What do you think about this?:
>>
>> <disk type='volume' device='disk'>
>> <driver name='qemu' type='raw'/>
>> <source pool='vhbapool_host8' volume='unit:0:0:1'/>
>> <target dev='hda' bus='ide'/>
>> </disk>
>>
>>
>> But I'd prefer to be able to use something like this instead:
>>
>>
>>
>> <disk type='volume' device='lun'>
>> <driver name='qemu' type='raw'/>
>> <source pool='vhbapool_host8' volume='unit:0:0:1'/>
>> <target dev='vda' bus='scsi'/>
>> </disk>
>>
>> But that might not be possible...?
>>
>
> The "volume" and "disk" or "volume" and "lun" syntax can be used
> somewhat interchangeably. As your point out the features for disk and
> lun are slightly different. Usage of the 'lun' syntax allows addition
> of the attribute "sgio='unfiltered'"
>
>>
>>
>> A couple of additional questions here:
>>
>> * Since the target device is already defined in the pool, I don't see the reason for defining it here as well, like in your example with the iscsi pool?
>
> Let's forget about iscsi
>
>> * I'd like to use virtio-scsi combined with the pool, is that possible?
>
> Works on my test guest (ok not the order from dumpxml):
>
> ...
> <controller type='scsi' index='0' model='virtio-scsi'>
> <alias name='scsi0'/>
> <address type='pci' domain='0x0000' bus='0x00' slot='0x05'
> function='0x0'/>
> </controller>
> ...
> <disk type='volume' device='lun'>
> <driver name='qemu' type='raw'/>
> <source pool='vhbapool_host3' volume='unit:0:4:0'/>
> <backingStore/>
> <target dev='sda' bus='scsi'/>
> <shareable/>
> <alias name='scsi0-0-0-0'/>
> <address type='drive' controller='0' bus='0' target='0' unit='0'/>
> </disk>
> ...
>
>> * If so, how do I define that? I understand I can define a controller separatly, but how do I tell the guest to use that specific controller in combination with that pool?
>
> See above... The controller has a "type", "index", and "model"... Then
> when adding the disk, use the type='drive' controller='#', where # is
> the index number from your virtio-scsi controller.
>
>> * Since the npiv pool obviously is a pool based on an fc initiator, the fc target can/will provision more lun's to that initiator, how will that effect the pool and the guest's access to new lun's? In this example the volume says 'unit:0:0:1', and I guess that will change if there will be more lun's in there? Or is that "volume unit" the "scsi target device", and can hold multiple lun's?
>>
>
> You can use 'virsh pool-refresh $poolname' - it will find new luns...
> Err, it *should* find new luns ;-) Existing 'unit:#:#:#' values
> shouldn't change - they should be "tied to" the same wwnn. Use "virsh
> vol-list $poolname" to see the Path. So when new ones are added they are
> given new unit number's. Reboots should find the same order.
>
>> ...more...
>>
>>
>> I've found something here in the RHEL7 virt guide:
>>
>>
>> <disk type='volume' device='lun' sgio='unfiltered'>
>> <driver name='qemu' type='raw'/>
>> <source pool='vhbapool_host3' volume='unit:0:0:0'/>
>> <target dev='sda' bus='scsi'/>
>> <shareable />
>> </disk>
>>
>
> Fair warning, use of sgio='unfiltered' does require some specific
> kernels... There were many "issues" with this - mostly related to kernel
> support. If not supported by the kernel, you are advised :
>
> error: Requested operation is not valid: unpriv_sgio is not supported by
> this kernel
>
>>
>>
>>
>> Question that shows up here is the multipath question. Since this is fibre channel it is of coarse multipath. The "target dev" says 'sda'. In a multipath dev list it should say "/dev/mapper/mpatha".
>>
>> How to handle that?
>>
>
> Uhh... multipath... Not my strong suit... I'm taking an example from a
> bz that you won't be able to read because it's marked private.
>
> Once you have your vHBA and scsi_hostM for that vHBA on the host you can
> use 'lsscsi' (you may have to yum/dnf install it - it's a very useful
> tool)...
>
>
> # lsscsi
> ...
> //assume scsi_host6 is the new vHBA created as follow
> [6:0:0:0] disk IBM 1726-4xx FAStT 0617 -
> [6:0:1:0] disk IBM 1726-4xx FAStT 0617 -
> [6:0:2:0] disk IBM 1726-4xx FAStT 0617 /dev/sdf
> [6:0:3:0] disk IBM 1726-4xx FAStT 0617 /dev/sdg
>
>
> You'll need an mpath pool:
>
> # virsh pool-dumpxml mpath
> <pool type='mpath'>
> <name>mpath</name>
> <source>
> </source>
> <target>
> <path>/dev/mapper</path>
> <permissions>
> <mode>0755</mode>
> <owner>-1</owner>
> <group>-1</group>
> </permissions>
> </target>
> </pool>
>
> # virsh pool-define mpath
> # virsh pool-start mpath
>
> # virsh vol-list mpath
> Name Path
> -----------------------------------------
> dm-0 /dev/mapper/3600a0b80005adb0b0000ab2d4cae9254
> dm-5 /dev/mapper/3600a0b80005ad1d700002dde4fa32ca8
> <=== this one is from vhba scsi_host6
>
> Then using something like:
>
> <disk type='block' device='lun' sgio='unfiltered'>
> <driver name='qemu' type='raw'/>
> <source dev='/dev/mapper/3600a0b80005ad1d700002dde4fa32ca8'/>
> <target dev='sda' bus='scsi'/>
> <alias name='scsi0-0-0-0'/>
> <address type='drive' controller='0' bus='0' target='0' unit='0'/>
> </disk>
>
> HTH,
>
> John
>
> (FWIW: I'm not sure how the leap of faith was taken that dm-5 is the
> vHBA for scsi_host6... Although I think it's from the wwnn for a volume
> in the vHBA as seen when using a virsh vol-list from a pool created
> using the vHBA within the bz).
>
>
>
>
> _______________________________________________
> libvirt-users mailing list
> libvirt-users at redhat.com
> https://www.redhat.com/mailman/listinfo/libvirt-users
>
>
>
>
> _______________________________________________
> libvirt-users mailing list
> libvirt-users at redhat.com
> https://www.redhat.com/mailman/listinfo/libvirt-users
>
>
>
More information about the libvirt-users
mailing list