[linux-lvm] Re: Installation Problems with 0.9
defranco at cup.hp.com
Wed Nov 29 18:51:44 UTC 2000
Thanks Heinz, one other question then, if I install
things in the following sequence:
I get two hunk failures (#3,4) in drivers/block/ll_rw_blk.c.
Are these expected or is there some other problem? If I
load the raid-2.2.17-A0 patch everything is ok, but then
after I boot that kernel I cannot create any raid devices
so I need the raid-2.2.17-A0 patch.
"Heinz J. Mauelshagen" wrote:
> Please don't use the lvm-0.9-2.2.17-new_raid.patch file.
> It has been deleted from our ftp site (it is still in the LVM tarball though).
> Go with the lvm-0.9-2.2.17-stock.patch instead.
> Sorry for the inconvenience.
> Heinz -- The LVM guy --
> On Mon, Nov 27, 2000 at 10:11:08AM -0800, John DeFranco wrote:
> > Hi,
> > Has anyone else had any problems install the
> > lvm-0.9-2.2.17-new_raid.patch? I'm using the following
> > procedure:
> > # gunzip -dc linux-2.2.17.tar.gz | tar -xvf -
> > # cd linux
> > # patch -p1 <../raid-2.2.17-A0
> > # patch -p1 <../linux-2.2.17-rawio.patch
> > # patch -p1 <../lvm-0.9-2.2.17-new_raid.patch
> > patching file `CREDITS'
> > patching file `Documentation/Configure.help'
> > Hunk #2 succeeded at 992 with fuzz 2 (offset 7 lines).
> > Hunk #3 succeeded at 1070 with fuzz 2.
> > patching file `Documentation/LVM-HOWTO'
> > patching file `drivers/block/Config.in'
> > Hunk #1 FAILED at 96.
> > 1 out of 1 hunk FAILED -- saving rejects to
> > drivers/block/Config.in.rej
> > patching file `drivers/block/Makefile'
> > Hunk #2 FAILED at 290.
> > Hunk #3 succeeded at 353 (offset 18 lines).
> > 1 out of 3 hunks FAILED -- saving rejects to
> > drivers/block/Makefile.rej
> > patching file `drivers/block/README.lvm'
> > patching file `drivers/block/genhd.c'
> > Reversed (or previously applied) patch detected! Assume -R?
> > [n]
> > .
> > .
> > .
> > There are about 5 files that have some problem. The end
> > result is not being able to build a new kernel due to
> > complication errors.
> > If I don't install the raid-2.2.17-A0 patch and then
> > install the lvm-0.9-2.2.17-stock.patch everything works
> > ok from the kernel end, but if I try to build an md
> > device I get the following:
> > analyzing super-block
> > disk 0: /dev/sdc1, 8883913kB, raid superblock at 8883840kB
> > disk 1: /dev/sdd1, 8883913kB, raid superblock at 8883840kB
> > mkraid: aborted, see the syslog and /proc/mdstat for
> > potential clues.
> > [root at ham linux]#
> > If I have the raid-2.2.17-A0 patch then this works.
> > Any clues?
> > Thanks!
> > --
> > ==========
> > Cheers
> > -jdf
> Heinz Mauelshagen Sistina Software Inc.
> Senior Consultant/Developer Bartningstr. 12
> 64289 Darmstadt
> Mauelshagen at Sistina.com +49 6151 7103 86
> FAX 7103 96
More information about the linux-lvm