[Ovirt-devel] Re: Fw: Install problems on fresh F10
daniel at sml.se
daniel at sml.se
Fri Dec 26 09:11:21 UTC 2008
I did post to ovirt-devel but I am not a registered user, so a moderator need to review my posting before it becomes available.
I will register, but right now I only have a few seconds to spare.
I try to add use "Add Virtual Machine" but the "Storage" is empty. My iSCSI and NFS storage says "State: pending_setup". What am I doing wrong?
Sincerely,
/bs66
----------------------------------------
From: Perry Myers <pmyers at redhat.com>
Sent: Friday, December 26, 2008 5:01 AM
To: daniel at sml.se, ovirt-devel at redhat.com
Subject: Re: Fw: Install problems on fresh F10
daniel at sml.se wrote:
> Thank you for your help.
No problem. Can you email ovirt-devel at redhat.com instead of me
individually? I don't mind getting the emails at all :) But it is better
if we keep discussions like this on the list, since there may be others
that could benefit from what we're discussing/figuring out.
> I got no errors issuing the commands, and I can now reach
> http://192.168.50.2/ovirt
>
> I am pretty sure I followed the install instructions, so I guess
> something more should be changed in there to get the install working
> smoothly.
The issues you were having had to do with the fact that you had to disable
NetworkManager. This is covered in the install instructions in the
section "Installing and Running the Appliance":
> NOTE: Fedora 10 uses NetworkManager by default to configure network interfaces. We recommend disabling NetworkManager and using the standard network scripts and network service. However, if you want to try running with NetworkManager enabled you can override the check with the -f flag to the create-ovirt-network script
We didn't explicitly list the instructions for disabling NetworkManager in
Fedora as there are plenty of resources for Fedora users in regards to
network configuration. For example, a quick Google search found this as
the #1 link when searching for "Fedora 10 disable NetworkManager":
http://www.mjmwired.net/resources/mjm-fedora-f10.html#network
But since this will probably be a common case for users of oVirt, I'll
incorporate the steps described in the above link into our Wiki and
provide a link to the Wiki page from the install instructions page.
The other problem you had was that libvirtd service was not started
properly. This is handled in the installation instructions under the
section "Getting oVirt RPMs" in step 4. That step should ensure that
libvirtd is running properly after upgrading/installing the daemon.
Thanks,
Perry
> Please find below the console output fyi.
>
> Thanks again.
> bs66
>
>
>
>
> [root at localhost network-scripts]# sudo service network restart
> Shutting down loopback interface: [ OK ]
> Disabling IPv4 packet forwarding: net.ipv4.ip_forward = 0
> [ OK ]
> Bringing up loopback interface: [ OK ]
> Bringing up interface eth0:
> Determining IP information for eth0... done.
> [ OK ]
> [root at localhost network-scripts]# ifconfig
> eth0 Link encap:Ethernet HWaddr 00:17:31:3F:20:85
> inet addr:192.168.0.205 Bcast:192.168.0.255 Mask:255.255.255.0
> inet6 addr: fe80::217:31ff:fe3f:2085/64 Scope:Link
> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
> RX packets:8 errors:0 dropped:0 overruns:0 frame:0
> TX packets:23 errors:0 dropped:0 overruns:0 carrier:0
> collisions:0 txqueuelen:1000
> RX bytes:1028 (1.0 KiB) TX bytes:5223 (5.1 KiB)
> Interrupt:19
>
> lo Link encap:Local Loopback
> inet addr:127.0.0.1 Mask:255.0.0.0
> inet6 addr: ::1/128 Scope:Host
> UP LOOPBACK RUNNING MTU:16436 Metric:1
> RX packets:40 errors:0 dropped:0 overruns:0 frame:0
> TX packets:40 errors:0 dropped:0 overruns:0 carrier:0
> collisions:0 txqueuelen:0
> RX bytes:11587 (11.3 KiB) TX bytes:11587 (11.3 KiB)
>
> ovirtbr0 Link encap:Ethernet HWaddr CE:86:E6:CF:A4:B5
> inet addr:192.168.50.1 Bcast:192.168.50.255 Mask:255.255.255.0
> inet6 addr: fe80::cc86:e6ff:fecf:a4b5/64 Scope:Link
> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
> RX packets:0 errors:0 dropped:0 overruns:0 frame:0
> TX packets:35 errors:0 dropped:0 overruns:0 carrier:0
> collisions:0 txqueuelen:0
> RX bytes:0 (0.0 b) TX bytes:5324 (5.1 KiB)
>
> virbr0 Link encap:Ethernet HWaddr FE:72:75:99:D3:E3
> inet addr:192.168.122.1 Bcast:192.168.122.255 Mask:255.255.255.0
> inet6 addr: fe80::fc72:75ff:fe99:d3e3/64 Scope:Link
> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
> RX packets:0 errors:0 dropped:0 overruns:0 frame:0
> TX packets:29 errors:0 dropped:0 overruns:0 carrier:0
> collisions:0 txqueuelen:0
> RX bytes:0 (0.0 b) TX bytes:5122 (5.0 KiB)
>
> [root at localhost network-scripts]# sudo service libvirtd restart
> Stopping libvirtd daemon: [ OK ]
> Starting libvirtd daemon: [ OK ]
> [root at localhost network-scripts]# sudo virsh net-list --all
> Name State Autostart
> -----------------------------------------
> default active yes
> ovirtbr0 active yes
>
> [root at localhost network-scripts]# sudo create-ovirt-network
> Currently active bridges:
> -------------------------
> bridge name bridge id STP enabled interfaces
> ovirtbr0 8000.000000000000 no
> pan0 8000.000000000000 no
> virbr0 8000.000000000000 yes
>
> Currently defined libvirt networks:
> -----------------------------------
> Name State Autostart
> -----------------------------------------
> default active yes
> ovirtbr0 active yes
>
>
> Removing ovirtbr0
> Network ovirtbr0 destroyed
>
> Network ovirtbr0 has been undefined
>
> Done Removing ovirtbr0
> Network ovirtbr0 defined from /tmp/tmp.mYuVHglF21
>
> Network ovirtbr0 started
>
> Network ovirtbr0 marked as autostarted
>
> net.ipv4.ip_forward = 1
> augtool> set /files/etc/sysctl.conf/net.ipv4.ip_forward 1
> augtool> save
> augtool>
> Shutting down dnsmasq: [ OK ]
> Starting dnsmasq: [ OK ]
> Currently active bridges:
> -------------------------
> bridge name bridge id STP enabled interfaces
> ovirtbr0 8000.000000000000 no
> pan0 8000.000000000000 no
> virbr0 8000.000000000000 yes
>
> Currently defined libvirt networks:
> -----------------------------------
> Name State Autostart
> -----------------------------------------
> default active yes
> ovirtbr0 active yes
>
>
> [root at localhost network-scripts]#
>
--
|=- Red Hat, Engineering, Emerging Technologies, Boston -=|
|=- Email: pmyers at redhat.com -=|
|=- Office: +1 412 474 3552 Mobile: +1 703 362 9622 -=|
|=- GnuPG: E65E4F3D 88F9 F1C9 C2F3 1303 01FE 817C C5D2 8B91 E65E 4F3D -=|
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://listman.redhat.com/archives/ovirt-devel/attachments/20081226/fef06f49/attachment-0001.htm>
More information about the ovirt-devel
mailing list