Turtle Beach Daytona sound card on 7.3
Bob Kinney
bc98kinney at yahoo.com
Fri Aug 20 19:54:09 UTC 2004
Hello--
I'm running RHL 7.3 on an HP Vectra VL6. I couldn't find support for
its Aztech card, so I put in a Turtle Beach Daytona I had laying around.
I installed Alsa, following the instructions here,
http://www.alsa-project.org/alsa-doc/doc-php/template.php?company=Turtle+Beach&card=Daytona&chip=SonicVibes+PCI&module=sonicvibes#opt
and here,
http://myweb.cableone.net/eviltwin69/ALSA.html
Running alsaconfig got me closer, but I still can't get any
sound from this setup. I know that I'm close, because the speakers pop from
time to time (on startup and shutdown, running gmix, and usually, but not
always, when I try to run aplay). I don't really know any good way to test
the card--I've been trying to run aplay or Gnome's sound event applet.
Any help, or a pointer to some decent troubleshooting would be appreciated.
-bc
Some hardware info:
[bob at vectra bob]$ cat /etc/modules.conf
alias parport_lowlevel parport_pc
alias eth0 pcnet32
alias usb-controller usb-uhci
# ALSA portion
alias char-major-116 snd
alias snd-card-0 snd-sonicvibes
# module options should go here
options isapnp=no
# OSS/Free portion
alias char-major-14 soundcore
alias sound-slot-0 snd-card-0
# card #1
alias sound-service-0-0 snd-mixer-oss
alias sound-service-0-1 snd-seq-oss
alias sound-service-0-3 snd-pcm-oss
alias sound-service-0-8 snd-seq-oss
alias sound-service-0-12 snd-pcm-oss
# --- BEGIN: Generated by ALSACONF, do not edit. ---
# --- ALSACONF verion 1.0.6 ---
alias char-major-116 snd
alias char-major-14 soundcore
alias sound-service-0-0 snd-mixer-oss
alias sound-service-0-1 snd-seq-oss
alias sound-service-0-3 snd-pcm-oss
alias sound-service-0-8 snd-seq-oss
alias sound-service-0-12 snd-pcm-oss
alias snd-card-0 snd-sonicvibes
alias sound-slot-0 snd-sonicvibes
# --- END: Generated by ALSACONF, do not edit. ---
[bob at vectra bob]$
[bob at vectra bob]$ ls /usr/src/alsa
alsa-driver-1.0.6a alsa-lib-1.0.6.tar alsa-utils-1.0.6.tar
alsa-driver-1.0.6a.tar alsa-tools-1.0.6.tar
alsa-lib-1.0.6 alsa-utils-1.0.6
[bob at vectra bob]$
[bob at vectra bob]$ aplay -D hw:0,0 espresso.wav
Playing WAVE 'espresso.wav' : Unsigned 8 bit, Rate 11025 Hz, Mono
aplay: pcm_write:1115: write error: Input/output error
[bob at vectra bob]$ aplay espresso.wav
Playing WAVE 'espresso.wav' : Unsigned 8 bit, Rate 11025 Hz, Mono
aplay: pcm_write:1115: write error: Input/output error
[bob at vectra bob]$
>From /var/log/messages:
Aug 20 14:18:59 vectra exiting on signal 15
Aug 20 14:20:43 vectra syslogd 1.4.1: restart.
Aug 20 14:20:43 vectra syslog: syslogd startup succeeded
Aug 20 14:20:43 vectra kernel: klogd 1.4.1, log source = /proc/kmsg started.
Aug 20 14:20:43 vectra syslog: klogd startup succeeded
Aug 20 14:20:43 vectra kernel: Linux version 2.4.20-28.7
(bhcompile at porky.devel.redhat.com) (gcc version 2.96 20000731 (Red Hat Linux
7.3 2.96-126)) #1 Thu Dec 18 11:31:59 EST 2003
Aug 20 14:20:43 vectra kernel: BIOS-provided physical RAM map:
Aug 20 14:20:43 vectra kernel: BIOS-e820: 0000000000000000 - 000000000009f800
(usable)
Aug 20 14:20:43 vectra kernel: BIOS-e820: 000000000009f800 - 00000000000a0000
(reserved)
Aug 20 14:20:43 vectra kernel: BIOS-e820: 00000000000ebc00 - 0000000000100000
(reserved)
Aug 20 14:20:43 vectra kernel: BIOS-e820: 0000000000100000 - 0000000010000000
(usable)
Aug 20 14:20:43 vectra kernel: BIOS-e820: 00000000fffe0000 - 0000000100000000
(reserved)
Aug 20 14:20:43 vectra kernel: 0MB HIGHMEM available.
Aug 20 14:20:43 vectra kernel: 256MB LOWMEM available.
Aug 20 14:20:43 vectra kernel: On node 0 totalpages: 65536
Aug 20 14:20:43 vectra kernel: zone(0): 4096 pages.
Aug 20 14:20:43 vectra kernel: zone(1): 61440 pages.
Aug 20 14:20:43 vectra kernel: zone(2): 0 pages.
Aug 20 14:20:43 vectra kernel: Kernel command line: ro root=/dev/hda3
hdd=ide-scsi
Aug 20 14:20:43 vectra kernel: ide_setup: hdd=ide-scsi
Aug 20 14:20:43 vectra kernel: Initializing CPU#0
Aug 20 14:20:43 vectra kernel: Detected 267.277 MHz processor.
Aug 20 14:20:43 vectra kernel: Console: colour VGA+ 80x25
Aug 20 14:20:43 vectra kernel: Calibrating delay loop... 532.48 BogoMIPS
Aug 20 14:20:43 vectra kernel: Memory: 253356k/262144k available (1175k kernel
code, 6352k reserved, 986k data, 120k init, 0k highmem)
Aug 20 14:20:43 vectra kernel: Dentry cache hash table entries: 32768 (order:
6, 262144 bytes)
Aug 20 14:20:43 vectra kernel: Inode cache hash table entries: 16384 (order: 5,
131072 bytes)
Aug 20 14:20:43 vectra kernel: Mount cache hash table entries: 512 (order: 0,
4096 bytes)
Aug 20 14:20:43 vectra kernel: Buffer-cache hash table entries: 16384 (order:
4, 65536 bytes)
Aug 20 14:20:43 vectra kernel: Page-cache hash table entries: 65536 (order: 6,
262144 bytes)
Aug 20 14:20:43 vectra kernel: CPU: L1 I cache: 16K, L1 D cache: 16K
Aug 20 14:20:43 vectra kernel: CPU: L2 cache: 512K
Aug 20 14:20:43 vectra kernel: Intel machine check architecture supported.
Aug 20 14:20:43 vectra kernel: Intel machine check reporting enabled on CPU#0.
Aug 20 14:20:43 vectra kernel: CPU: Intel Pentium II (Klamath) stepping 04
Aug 20 14:20:43 vectra kernel: Checking 'hlt' instruction... OK.
Aug 20 14:20:43 vectra kernel: POSIX conformance testing by UNIFIX
Aug 20 14:20:43 vectra kernel: mtrr: v1.40 (20010327) Richard Gooch
(rgooch at atnf.csiro.au)
Aug 20 14:20:43 vectra kernel: mtrr: detected mtrr type: Intel
Aug 20 14:20:43 vectra kernel: PCI: PCI BIOS revision 2.10 entry at 0xfd9c9,
last bus=1
Aug 20 14:20:43 vectra kernel: PCI: Using configuration type 1
Aug 20 14:20:43 vectra kernel: PCI: Probing PCI hardware
Aug 20 14:20:43 vectra kernel: PCI: Using IRQ router PIIX [8086/7110] at
00:04.0
Aug 20 14:20:43 vectra kernel: Limiting direct PCI/PCI transfers.
Aug 20 14:20:43 vectra kernel: isapnp: Scanning for PnP cards...
Aug 20 14:20:43 vectra kernel: isapnp: No Plug & Play device found
Aug 20 14:20:43 vectra kernel: Linux NET4.0 for Linux 2.4
Aug 20 14:20:43 vectra kernel: Based upon Swansea University Computer Society
NET3.039
Aug 20 14:20:43 vectra kernel: Initializing RT netlink socket
Aug 20 14:20:43 vectra kernel: apm: BIOS version 1.2 Flags 0x03 (Driver version
1.16)
Aug 20 14:20:43 vectra kernel: Starting kswapd
Aug 20 14:20:43 vectra kernel: VFS: Disk quotas vdquot_6.5.1
Aug 20 14:20:43 vectra kernel: pty: 2048 Unix98 ptys configured
Aug 20 14:20:43 vectra kernel: Serial driver version 5.05c (2001-07-08) with
MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI ISAPNP enabled
Aug 20 14:20:43 vectra kernel: ttyS0 at 0x03f8 (irq = 4) is a 16550A
Aug 20 14:20:43 vectra kernel: Real Time Clock Driver v1.10e
Aug 20 14:20:43 vectra kernel: Floppy drive(s): fd0 is 1.44M
Aug 20 14:20:43 vectra kernel: FDC 0 is a National Semiconductor PC87306
Aug 20 14:20:43 vectra kernel: NET4: Frame Diverter 0.46
Aug 20 14:20:43 vectra kernel: RAMDISK driver initialized: 16 RAM disks of
4096K size 1024 blocksize
Aug 20 14:20:43 vectra portmap: portmap startup succeeded
Aug 20 14:20:43 vectra kernel: Uniform Multi-Platform E-IDE driver Revision:
7.00beta3-.2.4
Aug 20 14:20:43 vectra kernel: ide: Assuming 33MHz system bus speed for PIO
modes; override with idebus=xx
Aug 20 14:20:43 vectra kernel: PIIX4: IDE controller at PCI slot 00:04.1
Aug 20 14:20:43 vectra kernel: PIIX4: chipset revision 1
Aug 20 14:20:43 vectra kernel: PIIX4: not 100%% native mode: will probe irqs
later
Aug 20 14:20:43 vectra kernel: ide0: BM-DMA at 0xfcb0-0xfcb7, BIOS
settings: hda:pio, hdb:DMA
Aug 20 14:20:43 vectra kernel: ide1: BM-DMA at 0xfcb8-0xfcbf, BIOS
settings: hdc:DMA, hdd:DMA
Aug 20 14:20:43 vectra kernel: hda: ST380021A, ATA DISK drive
Aug 20 14:20:43 vectra kernel: hdb: ST34321A, ATA DISK drive
Aug 20 14:20:43 vectra kernel: blk: queue c0378440, I/O limit 4095Mb (mask
0xffffffff)
Aug 20 14:20:43 vectra kernel: blk: queue c0378584, I/O limit 4095Mb (mask
0xffffffff)
Aug 20 14:20:43 vectra kernel: hdc: MATSHITA CR-588, ATAPI CD/DVD-ROM drive
Aug 20 14:20:43 vectra kernel: hdd: AOPEN CD-RW CRW2440, ATAPI CD/DVD-ROM drive
Aug 20 14:20:43 vectra kernel: ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Aug 20 14:20:43 vectra kernel: ide1 at 0x170-0x177,0x376 on irq 15
Aug 20 14:20:43 vectra kernel: hda: attached ide-disk driver.
Aug 20 14:20:43 vectra kernel: hda: host protected area => 1
Aug 20 14:20:43 vectra kernel: hda: 156301488 sectors (80026 MB) w/2048KiB
Cache, CHS=9729/255/63, UDMA(33)
Aug 20 14:20:43 vectra kernel: hdb: attached ide-disk driver.
Aug 20 14:20:43 vectra kernel: hdb: task_no_data_intr: status=0x51 { DriveReady
SeekComplete Error }
Aug 20 14:20:43 vectra kernel: hdb: task_no_data_intr: error=0x04 {
DriveStatusError }
Aug 20 14:20:43 vectra kernel: hdb: 8405775 sectors (4304 MB) w/128KiB Cache,
CHS=555/240/63, UDMA(33)
Aug 20 14:20:43 vectra kernel: ide-floppy driver 0.99.newide
Aug 20 14:20:43 vectra kernel: Partition check:
Aug 20 14:20:43 vectra kernel: hda: [DM6:DDO] [remap +63] [9729/255/63] hda1
hda2 hda3 hda4 < hda5 >
Aug 20 14:20:43 vectra kernel: hdb: hdb1 hdb2 < hdb5 >
Aug 20 14:20:43 vectra kernel: ide-floppy driver 0.99.newide
Aug 20 14:20:43 vectra kernel: md: md driver 0.90.0 MAX_MD_DEVS=256,
MD_SB_DISKS=27
Aug 20 14:20:43 vectra kernel: md: Autodetecting RAID arrays.
Aug 20 14:20:43 vectra kernel: md: autorun ...
Aug 20 14:20:43 vectra kernel: md: ... autorun DONE.
Aug 20 14:20:43 vectra kernel: NET4: Linux TCP/IP 1.0 for NET4.0
Aug 20 14:20:43 vectra kernel: IP Protocols: ICMP, UDP, TCP, IGMP
Aug 20 14:20:43 vectra kernel: IP: routing cache hash table of 2048 buckets,
16Kbytes
Aug 20 14:20:43 vectra kernel: TCP: Hash tables configured (established 16384
bind 32768)
Aug 20 14:20:43 vectra kernel: Linux IP multicast router 0.06 plus PIM-SM
Aug 20 14:20:43 vectra kernel: NET4: Unix domain sockets 1.0/SMP for Linux
NET4.0.
Aug 20 14:20:43 vectra kernel: RAMDISK: Compressed image found at block 0
Aug 20 14:20:43 vectra kernel: Freeing initrd memory: 119k freed
Aug 20 14:20:43 vectra kernel: VFS: Mounted root (ext2 filesystem).
Aug 20 14:20:43 vectra kernel: Journalled Block Device driver loaded
Aug 20 14:20:43 vectra kernel: kjournald starting. Commit interval 5 seconds
Aug 20 14:20:43 vectra kernel: EXT3-fs: mounted filesystem with ordered data
mode.
Aug 20 14:20:43 vectra kernel: Freeing unused kernel memory: 120k freed
Aug 20 14:20:43 vectra kernel: Adding Swap: 522072k swap-space (priority -1)
Aug 20 14:20:43 vectra kernel: usb.c: registered new driver usbdevfs
Aug 20 14:20:43 vectra kernel: usb.c: registered new driver hub
Aug 20 14:20:43 vectra kernel: usb-uhci.c: $Revision: 1.275 $ time 11:37:26 Dec
18 2003
Aug 20 14:20:43 vectra kernel: usb-uhci.c: High bandwidth mode enabled
Aug 20 14:20:43 vectra kernel: PCI: Found IRQ 9 for device 00:04.2
Aug 20 14:20:43 vectra kernel: PCI: Sharing IRQ 9 with 00:0c.0
Aug 20 14:20:43 vectra kernel: usb-uhci.c: USB UHCI at I/O 0xfce0, IRQ 9
Aug 20 14:20:43 vectra kernel: usb-uhci.c: Detected 2 ports
Aug 20 14:20:43 vectra kernel: usb.c: new USB bus registered, assigned bus
number 1
Aug 20 14:20:43 vectra kernel: hub.c: USB hub found
Aug 20 14:20:43 vectra kernel: hub.c: 2 ports detected
Aug 20 14:20:43 vectra kernel: usb-uhci.c: v1.275:USB Universal Host Controller
Interface driver
Aug 20 14:20:43 vectra kernel: hub.c: new USB device 00:04.2-1, assigned
address 2
Aug 20 14:20:43 vectra kernel: usb.c: USB device 2 (vend/prod 0x3f0/0x1411) is
not claimed by any active driver.
Aug 20 14:20:43 vectra kernel: usb.c: registered new driver usblp
Aug 20 14:20:43 vectra kernel: printer.c: usblp0: USB Bidirectional printer dev
2 if 0 alt 1 proto 2 vid 0x03F0 pid 0x1411
Aug 20 14:20:43 vectra kernel: printer.c: v0.11: USB Printer Device Class
driver
Aug 20 14:20:43 vectra kernel: EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,3),
internal journal
Aug 20 14:20:43 vectra kernel: kjournald starting. Commit interval 5 seconds
Aug 20 14:20:43 vectra kernel: EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,2),
internal journal
Aug 20 14:20:43 vectra kernel: EXT3-fs: mounted filesystem with ordered data
mode.
Aug 20 14:20:43 vectra kernel: hdc: attached ide-cdrom driver.
Aug 20 14:20:43 vectra kernel: hdc: ATAPI 32X CD-ROM drive, 128kB Cache, DMA
Aug 20 14:20:43 vectra kernel: Uniform CD-ROM driver Revision: 3.12
Aug 20 14:20:43 vectra kernel: SCSI subsystem driver Revision: 1.00
Aug 20 14:20:43 vectra kernel: hdd: attached ide-scsi driver.
Aug 20 14:20:43 vectra kernel: scsi0 : SCSI host adapter emulation for IDE
ATAPI devices
Aug 20 14:20:43 vectra kernel: Vendor: AOPEN Model: CD-RW CRW2440
Rev: 2.08
Aug 20 14:20:43 vectra kernel: Type: CD-ROM
ANSI SCSI revision: 02
Aug 20 14:20:43 vectra kernel: hdc: DMA disabled
Aug 20 14:20:43 vectra kernel: hdd: DMA disabled
Aug 20 14:20:43 vectra kernel: parport0: PC-style at 0x378 (0x778)
[PCSPP,TRISTATE,EPP]
Aug 20 14:20:43 vectra kernel: parport0: irq 7 detected
Aug 20 14:20:43 vectra kernel: ip_conntrack version 2.1 (2048 buckets, 16384
max) - 292 bytes per conntrack
Aug 20 14:20:43 vectra kernel: pcnet32.c:v1.27a 10.02.2002
tsbogend at alpha.franken.de
Aug 20 14:20:43 vectra kernel: PCI: Found IRQ 11 for device 00:06.0
Aug 20 14:20:43 vectra kernel: pcnet32: PCnet/FAST 79C971 at 0xfcc0, 00 60 b0
ed 14 0a
Aug 20 14:20:43 vectra kernel: tx_start_pt(0x0c00):~220 bytes,
BCR18(9861):BurstWrEn BurstRdEn NoUFlow
Aug 20 14:20:43 vectra nfslock: rpc.statd startup succeeded
Aug 20 14:20:43 vectra kernel: SRAMSIZE=0x7f00, SRAM_BND=0x3f00, assigned
IRQ 11.
Aug 20 14:20:44 vectra kernel: eth0: registered as PCnet/FAST 79C971
Aug 20 14:20:44 vectra kernel: pcnet32: 1 cards_found.
Aug 20 14:20:44 vectra rpc.statd[830]: Version 0.3.3 Starting
Aug 20 14:20:44 vectra keytable: Loading keymap: succeeded
Aug 20 14:20:44 vectra keytable: Loading system font: succeeded
Aug 20 14:20:44 vectra random: Initializing random number generator: succeeded
Aug 20 14:20:45 vectra netfs: Mounting other filesystems: succeeded
Aug 20 14:20:45 vectra apmd[942]: Version 3.0.2 (APM BIOS 1.2, Linux driver
1.16)
Aug 20 14:20:45 vectra apmd: apmd startup succeeded
Aug 20 14:20:45 vectra autofs: automount startup succeeded
Aug 20 14:20:46 vectra sshd: Starting sshd:
Aug 20 14:20:46 vectra sshd: succeeded
Aug 20 14:20:46 vectra sshd:
Aug 20 14:20:46 vectra rc: Starting sshd: succeeded
Aug 20 14:20:46 vectra apmd[942]: Charge: * * * (-1% unknown)
Aug 20 14:20:48 vectra xinetd[1030]: xinetd Version 2.3.11 started with libwrap
loadavg options compiled in.
Aug 20 14:20:48 vectra xinetd[1030]: Started working: 1 available service
Aug 20 14:20:50 vectra xinetd: xinetd startup succeeded
Aug 20 14:20:51 vectra lpd: lpd startup succeeded
Aug 20 14:20:52 vectra sendmail: sendmail startup succeeded
Aug 20 14:20:53 vectra gpm: gpm startup succeeded
Aug 20 14:20:53 vectra FreeWnn: Starting FreeWnn:
Aug 20 14:20:53 vectra FreeWnn:
Aug 20 14:20:53 vectra rc: Starting FreeWnn: succeeded
Aug 20 14:20:54 vectra cWnn: Starting cWnn:
Aug 20 14:20:54 vectra cWnn:
Aug 20 14:20:54 vectra rc: Starting cWnn: succeeded
Aug 20 14:20:55 vectra canna: cannaserver startup succeeded
Aug 20 14:20:55 vectra crond: crond startup succeeded
Aug 20 14:20:56 vectra kWnn: Starting kWnn:
Aug 20 14:20:56 vectra kWnn:
Aug 20 14:20:56 vectra rc: Starting kWnn: succeeded
Aug 20 14:20:56 vectra tWnn: Starting tWnn:
Aug 20 14:20:56 vectra tWnn:
Aug 20 14:20:56 vectra rc: Starting tWnn: succeeded
Aug 20 14:20:58 vectra xfs: listening on port 7100
Aug 20 14:20:58 vectra xfs: xfs startup succeeded
Aug 20 14:20:58 vectra anacron: anacron startup succeeded
Aug 20 14:20:58 vectra atd: atd startup succeeded
Aug 20 14:20:58 vectra xfs: ignoring font path element
/usr/X11R6/lib/X11/fonts/cyrillic (unreadable)
Aug 20 14:20:58 vectra xfs: ignoring font path element
/usr/X11R6/lib/X11/fonts/local (unreadable)
Aug 20 14:20:58 vectra rhnsd: rhnsd startup succeeded
Aug 20 14:20:59 vectra rhnsd[1358]: Red Hat Network Services Daemon starting
up.
Aug 20 14:20:59 vectra linuxconf: Running Linuxconf hooks: succeeded
Aug 20 14:21:16 vectra gdm(pam_unix)[1396]: session opened for user bob by
(uid=0)
Aug 20 14:21:19 vectra kernel: PCI: Found IRQ 10 for device 00:0a.0
Aug 20 14:21:19 vectra kernel: ALSA ../alsa-kernel/pci/sonicvibes.c:1257: BIOS
did not allocate DDMA channel A i/o, allocated at 0x7a00
Aug 20 14:21:19 vectra kernel: ALSA ../alsa-kernel/pci/sonicvibes.c:1262: BIOS
did not allocate DDMA channel C i/o, allocated at 0x7a10
Aug 20 14:21:25 vectra gnome-name-server[1529]: starting
Aug 20 14:21:25 vectra gnome-name-server[1530]: starting
Aug 20 14:21:25 vectra gnome-name-server[1529]: name server starting
Aug 20 14:21:25 vectra gnome-name-server[1530]: name server was running on
display, exiting
Aug 20 14:21:25 vectra kernel: Attached scsi CD-ROM sr0 at scsi0, channel 0, id
0, lun 0
Aug 20 14:21:25 vectra kernel: sr0: scsi3-mmc drive: 40x/40x writer cd/rw
xa/form2 cdda tray
Aug 20 14:21:26 vectra gconfd (bob-1539): starting (version 1.0.9), pid 1539
user 'bob'
Aug 20 14:21:33 vectra kernel: cdrom: This disc doesn't have any tracks I
recognize!
Aug 20 14:21:43 vectra login(pam_unix)[1379]: session opened for user bob by
LOGIN(uid=0)
Aug 20 14:21:43 vectra -- bob[1379]: LOGIN ON tty1 BY bob
Aug 20 14:25:58 vectra modprobe: modprobe: Can't locate module sound-slot-1
Aug 20 14:25:58 vectra modprobe: modprobe: Can't locate module
sound-service-1-0
Aug 20 14:26:40 vectra su(pam_unix)[1758]: session opened for user root by
bob(uid=500)
__________________________________
Do you Yahoo!?
Yahoo! Mail - 50x more storage than other providers!
http://promotions.yahoo.com/new_mail
More information about the Redhat-install-list
mailing list