IPTables and forward

Wed Oct 27 20:56:37 UTC 2004

Ok, I was wrong, I look it the error on Iptables (because I’m new using it I
thought that I put something wrong), well that I found is RX (reception)
errors on the eth0.

This is that ifconfig show:
eth0      Link encap:Ethernet  HWaddr 00:C0:9F:46:25:97
          inet addr:101.32.212.53  Bcast:101.32.212.255  Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:4329 errors:2843 dropped:0 overruns:0 frame:1590
          TX packets:6536 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:309036 (301.7 Kb)  TX bytes:2020769 (1.9 Mb)
          Interrupt:18 Base address:0xece0 Memory:fe1e0000-fe200000

As you can see, there is 3843 errors. On the RX, the streigs think, it’s
that I can received smaller files then 700b, greater files are loosing, and
other smaller files pass but they arrive empty.

First I change the network cable, but it not work..

There is two equal cards eth0 and eth1, when eth1 is working perfectly, so I
try to found any difference on the driver, PCI or IRQ configuration, but the
only difference found is that the eth0 (bad card) appear in the  /proc/pci
file as No bursts and the eth1 (good) card appear as Latency=32, and don’t
know what it mean or how can I change it.

Any one know some about it?

This are some related files.

/proc/pci report:
    Ethernet controller: PCI device 8086:1075 (Intel Corp.) (rev 0).
      IRQ 18.
      Master Capable.  No bursts.  Min Gnt=255.
      Non-prefetchable 32 bit memory at 0xfe1e0000 [0xfe1fffff].
      I/O at 0xece0 [0xecff].
  Bus  3, device   2, function  0:
    Ethernet controller: PCI device 8086:1076 (Intel Corp.) (rev 0).
      IRQ 21.
      Master Capable.  Latency=32.  Min Gnt=255.
      Non-prefetchable 32 bit memory at 0xfdee0000 [0xfdefffff].
      I/O at 0xdcc0 [0xdcff].
  Bus  3, device   3, function  0:
    Ethernet controller: Davicom Semiconductor, Inc. Ethernet 100/10 MBit
(rev 49).

/proc/interrupts report:
           CPU0       CPU1
  0:    4243967    4241237    IO-APIC-edge  timer
  1:          4          0    IO-APIC-edge  keyboard
  2:          0          0          XT-PIC  cascade
  8:          1          0    IO-APIC-edge  rtc
 12:         28          0    IO-APIC-edge  PS/2 Mouse
 14:         21          0    IO-APIC-edge  ide0
 15:      62241      52518    IO-APIC-edge  libata
 16:          0          0   IO-APIC-level  usb-uhci
 18:      10959      41562   IO-APIC-level  eth0
 19:          0          0   IO-APIC-level  usb-uhci
 21:     208689          0   IO-APIC-level  eth1
 22:          8     197601   IO-APIC-level  eth2
 23:          0          0   IO-APIC-level  ehci-hcd
NMI:          1          0
LOC:    8484883    8484882
ERR:          0
MIS:          0

/proc/ioports report:
d400-d4ff : ATI Technologies Inc Rage XL
d800-d8ff : Davicom Semiconductor, Inc. Ethernet 100/10 MBit
  d800-d8ff : dmfe
dcc0-dcff : PCI device 8086:1076 (Intel Corp.) (good card)
  dcc0-dcff : e1000
e000-efff : PCI Bus #01
  ece0-ecff : PCI device 8086:1075 (Intel Corp.) (bad card)
    ece0-ecff : e1000

Thank you so much.

Regards.

-----Original Message-----
From: redhat-list-bounces at redhat.com
[mailto:redhat-list-bounces at redhat.com]On Behalf Of Marco A. Ramos
Sent: Wednesday, 13 October, 2004 11:37 AM
To: redhat-list at redhat.com
Subject: IPTables and forward

Hello, every one!

I have a problem using Iptables and Forward.

First some data to explain the problem

OS: RedHat Enterprice 3 WS

Use of service: transmit small text files using sockets, the sofware contact
the remote server, transmit the file and disconnect it.

Connection: From a Linux Server to a Remote Unix Server using Frame Relay
Technology.

This schemes was working perfectly for two year:

Server –Router -----FrameRelay----Router---Other equipment—Server

         <--------- Transmitting and receiving connections --------->

But for some requirements we have to add en LinuxServer before the remote
other equipment:

Server –Router --FrameRelay--Router--New Linux Server---Other
equiment—Server

         <--------- Transmitting and receiving
connections ---------------------------->

The new Linux server, must to make NAT, forward and redirect connections,
using IPtables.

The problems is, since we add the new server, we start to have tree
problems: 1) loose some connections; 2) The connection some time is slowly;
and 3) some files are transmit it empty.

I reduce the function of the New Linux Server to just make forward (the
connection get in from one network card and get out from other) with out any
security rule, but the problem still happen.

Any idea?

Thank you so much, regards.
 Marco Antonio Ramos
 Centro de Prevalidación
 mramos at sanyoval.net
  (664) 647-44-66/25/44
  Fax: (664) 647-44-33

--
redhat-list mailing list
unsubscribe mailto:redhat-list-request at redhat.com?subject=unsubscribe
https://www.redhat.com/mailman/listinfo/redhat-list