Problem at booting
Vivek Mangal
vivek.mangal9685 at gmail.com
Thu Feb 14 07:22:39 UTC 2008
But, Which card ?
and how u can say that ?
tell me
On 2/13/08, Vivek Mangal <vivek.mangal9685 at gmail.com> wrote:
>
> The output of command #lspci -vv is
> ----------------------------------------
> pcilib: Resource 3 in /sys/bus/pci/devices/0000:00:00:0/resource has a
> 64-bit address, ignoring
> 00:00.0 Host bridge: ATI Technologies Inc: Unknown device 5a33 (rev 01)
> Subsystem: Intel Corporation: Unknown device d600
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort+ >SERR- <PERR-
> Latency: 64
> Region 3: Memory at <ignored> (64-bit, non-prefetchable)
>
> 00:01.0 PCI bridge: ATI Technologies Inc: Unknown device 5a3f (prog-if 00
> [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 99
> Bus: primary=00, secondary=01, subordinate=01, sec-latency=68
> I/O behind bridge: 0000e000-0000efff
> Memory behind bridge: fde00000-fdefffff
> Prefetchable memory behind bridge: f0000000-f7ffffff
> Secondary status: 66Mhz+ FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort+ <SERR- <PERR-
> BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
> Capabilities: [b0] #0d [0000]
>
> 00:11.0 IDE interface: ATI Technologies Inc ATI 437A Serial ATA Controller
> (rev 80) (prog-if 8f [Master SecP SecO PriP PriO])
> Subsystem: Intel Corporation: Unknown device d600
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 64, Cache Line Size 08
> Interrupt: pin A routed to IRQ 169
> Region 0: I/O ports at ff00 [size=8]
> Region 1: I/O ports at fe00 [size=4]
> Region 2: I/O ports at fd00 [size=8]
> Region 3: I/O ports at fc00 [size=4]
> Region 4: I/O ports at fb00 [size=16]
> Region 5: Memory at fe02f000 (32-bit, non-prefetchable) [size=512]
> Expansion ROM at fdf80000 [disabled] [size=512K]
> Capabilities: [60] Power Management version 2
> Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=2 PME-
> Capabilities: [50] Message Signalled Interrupts: 64bit- Queue=0/0
> Enable-
> Address: 00000000 Data: 0000
>
> 00:12.0 IDE interface: ATI Technologies Inc ATI 4379 Serial ATA Controller
> (rev 80) (prog-if 8f [Master SecP SecO PriP PriO])
> Subsystem: Intel Corporation: Unknown device d600
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 64, Cache Line Size 08
> Interrupt: pin A routed to IRQ 177
> Region 0: I/O ports at fa00 [size=8]
> Region 1: I/O ports at f900 [size=4]
> Region 2: I/O ports at f800 [size=8]
> Region 3: I/O ports at f700 [size=4]
> Region 4: I/O ports at f600 [size=16]
> Region 5: Memory at fe02e000 (32-bit, non-prefetchable) [size=512]
> Expansion ROM at fdf80000 [disabled] [size=512K]
> Capabilities: [60] Power Management version 2
> Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=2 PME-
> Capabilities: [50] Message Signalled Interrupts: 64bit- Queue=0/0
> Enable-
> Address: 00000000 Data: 0000
>
> 00:13.0 USB Controller: ATI Technologies Inc IXP SB400 USB Host Controller
> (rev 80) (prog-if 10 [OHCI])
> Subsystem: Intel Corporation: Unknown device d600
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 64, Cache Line Size 20
> Interrupt: pin A routed to IRQ 185
> Region 0: Memory at fe02d000 (32-bit, non-prefetchable) [size=4K]
> Capabilities: [d0] Message Signalled Interrupts: 64bit- Queue=0/0
> Enable-
> Address: 00000000 Data: 0000
>
> 00:13.1 USB Controller: ATI Technologies Inc IXP SB400 USB Host Controller
> (rev 80) (prog-if 10 [OHCI])
> Subsystem: Intel Corporation: Unknown device d600
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 64, Cache Line Size 20
> Interrupt: pin A routed to IRQ 185
> Region 0: Memory at fe02c000 (32-bit, non-prefetchable) [size=4K]
> Capabilities: [d0] Message Signalled Interrupts: 64bit- Queue=0/0
> Enable-
> Address: 00000000 Data: 0000
>
> 00:13.2 USB Controller: ATI Technologies Inc IXP SB400 USB2 Host
> Controller (rev 80) (prog-if 20 [EHCI])
> Subsystem: Intel Corporation: Unknown device d600
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 64, Cache Line Size 20
> Interrupt: pin A routed to IRQ 185
> Region 0: Memory at fe02b000 (32-bit, non-prefetchable) [size=4K]
> Capabilities: [dc] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
> PME(D0+,D1+,D2+,D3hot+,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> Bridge: PM- B3+
> Capabilities: [d0] Message Signalled Interrupts: 64bit- Queue=0/0
> Enable-
> Address: 00000000 Data: 0000
>
> 00:14.0 SMBus: ATI Technologies Inc IXP SB400 SMBus Controller (rev 82)
> Subsystem: Intel Corporation: Unknown device d600
> Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Region 0: I/O ports at 0b00 [size=16]
> Region 1: Memory at fe02a000 (32-bit, non-prefetchable) [size=1K]
>
> 00:14.1 IDE interface: ATI Technologies Inc Standard Dual Channel PCI IDE
> Controller ATI (rev 80) (prog-if 8a [Master SecP PriP])
> Subsystem: Intel Corporation: Unknown device d600
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 64
> Interrupt: pin A routed to IRQ 193
> Region 0: I/O ports at <unassigned>
> Region 1: I/O ports at <unassigned>
> Region 2: I/O ports at <unassigned>
> Region 3: I/O ports at <unassigned>
> Region 4: I/O ports at f400 [size=16]
> Capabilities: [70] Message Signalled Interrupts: 64bit- Queue=0/0
> Enable-
> Address: 00000000 Data: 0000
>
> 00:14.2 Class 0403: ATI Technologies Inc: Unknown device 437b (rev 01)
> Subsystem: Intel Corporation: Unknown device d600
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 64, Cache Line Size 08
> Interrupt: pin ? routed to IRQ 193
> Region 0: Memory at fe024000 (64-bit, non-prefetchable) [size=16K]
> Capabilities: [50] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA
> PME(D0+,D1-,D2-,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [60] Message Signalled Interrupts: 64bit+ Queue=0/0
> Enable-
> Address: 0000000000000000 Data: 0000
>
> 00:14.3 ISA bridge: ATI Technologies Inc IXP SB400 PCI-ISA Bridge (rev 80)
> Subsystem: Intel Corporation: Unknown device d600
> Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
>
> 00:14.4 PCI bridge: ATI Technologies Inc IXP SB400 PCI-PCI Bridge (rev 80)
> (prog-if 01 [Subtractive decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop+ ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 64
> Bus: primary=00, secondary=02, subordinate=02, sec-latency=64
> I/O behind bridge: 0000d000-0000dfff
> Memory behind bridge: fdd00000-fddfffff
> Prefetchable memory behind bridge: fdc00000-fdcfffff
> Secondary status: 66Mhz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort+ <SERR- <PERR-
> BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
>
> 01:05.0 VGA compatible controller: ATI Technologies Inc: Unknown device
> 5a61 (prog-if 00 [VGA])
> Subsystem: Intel Corporation: Unknown device d600
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 64 (2000ns min), Cache Line Size 08
> Interrupt: pin A routed to IRQ 201
> Region 0: Memory at f0000000 (32-bit, prefetchable) [size=128M]
> Region 1: I/O ports at ee00 [size=256]
> Region 2: Memory at fdef0000 (32-bit, non-prefetchable) [size=64K]
> Capabilities: [50] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [80] Message Signalled Interrupts: 64bit- Queue=0/0
> Enable-
> Address: 00000000 Data: 0000
>
> 02:02.0 Ethernet controller: Realtek Semiconductor Co., Ltd.
> RTL-8139/8139C/8139C+ (rev 10)
> Subsystem: Intel Corporation: Unknown device d600
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 64 (8000ns min, 16000ns max)
> Interrupt: pin A routed to IRQ 209
> Region 0: I/O ports at de00 [size=256]
> Region 1: Memory at fddff000 (32-bit, non-prefetchable) [size=256]
> Capabilities: [50] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
> PME(D0-,D1+,D2+,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 02:04.0 Serial controller: Exar Corp. XR17C158 Octal UART (rev 09)
> (prog-if 02 [16550])
> Subsystem: Unknown device 2205:2004
> Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Interrupt: pin A routed to IRQ 201
> Region 0: Memory at fddfe000 (32-bit, non-prefetchable) [size=4K]
> ------------------------------------
>
>
> On 2/12/08, Vivek Mangal <vivek.mangal9685 at gmail.com> wrote:
> >
> > hello all,
> > My new PC show a message all time at the booting
> > i can not under stand what is the problem ?
> > and how can i recover it ?
> > problem is that
> >
> > PCI: cannot allocate resource region 3 of devices 0000:00:00:0
> >
> > if any have any idea then please tell me.
> >
>
>
More information about the redhat-list
mailing list